Slingshot PHANTASM E 990/710 User manual

PHANTASM
E 990 / 710 LOWER PACKAGE

PHANTASM E 990/710 PACKAGE
The E 990/710 Lower Package was developed by our design team
using the feedback from Phantasm riders worldwide. Riders who are
looking speed and agility, but still want great confidence-inspiring
stability should look no further than the E 990 Lower Combination.
This package of E 990 Front Wing, PS 400 Rear Stabilizer and 710
Fuse is by far our most all-around performance foil set-up we make.
SKU: 1230490001
SKU: 122825019
SKU: 122826000
SKU: 122824002
SKU: 122827015
*SKU: 121237008
E 990
E990 FRONT WING
NEOPRENE COVER
PHANTASM 400 STABILIZER
NEOPRENE COVER
PHANTASM LARGE
CARRYING CASE
FRONT WING
*COMPLETE HARDWARE
PACKAGE
T30 TORX WRENCH
710 FUSELAGE
SKU: 121290710
M6 X 30mm
FLATHEAD
SCREW
M6 X 35mm
FLATHEAD
SCREW
M6 X 25mm
FLATHEAD
SCREW
M6 X 25mm
SOCKET HEAD
SCREWS
M6 X 18mm
FLATHEAD
SCREWS
PS 400
STABILIZER
*SKU: 122827015
*SKU: 122827015
*SKU: 122827015
*SKU: 122827015 *SKU: 122827015
SKU: 121237004
COMPLETE FOIL SETUP
PTM 926 / 872
PTM 926 / 710
PTM 684 / 710
PFI 835 & 928 / 710
PFI 633 & 730 / 710 PFH 767 / 710
PTM 730 / 710
PFI 730 / 872
PFI 928 / 872

FOIL ASSEMBLY
1. Coat all bolt hardware with Lanolin oil or a marine-grade grease and
wrap with Teflon tape before assembling your foil. (see maintenance
section for details)
2. Connect the front wing to the fuselage using the M6x30mm flathead
screw for the forward hole, the M6x35mm screw for the center hole and
the M6x25mm screw for the third hole.
3. Connect the rear wing to the fuselage using the two M6 x 18mm flathead
screws.
4. Position the mast so that it is vertical. Be careful of knocking the mast
over, attaching the pedestal to an upside down board can help with
stability.
5. Insert the mast foot into the fuselage slot so that the 3 holes align
and fasten with the three M6x25mm socket head screws. It may be
necessary to use a rubber mallet to fit the fuselage on and o the mast
for the first few sessions.
Coat all hardware
5
2
4
1
3

1. To attach your fully assembled foil to your board, place your board
upside down and slide the four female pieces of your mounting
hardware into slots in the tracks of your board, two on each side.
Note: Mounting hardware comes packaged with Slingshot foil
boards, and is not included in the foil package.
2. Carefully place your foil over the mounting track so the front hole
pattern in the pedestal line up with the mounting hardware. Be extra
cautious with your foil in this position; components are fragile and
can damage easily if it gets knocked down or blown over.
3. Bolt your foil to your board, tightening each bolt bit by bit until all
four are equally tight.
ATTACHING FOIL TO BOARD
s. Thi
will be a little tricky with the bolts covered in a layer of
Lanolin oil/ or marine-grade grease, but it acts as a second
SKU: 19236110
SKU: 120711033
PFI 633
NEOPRENE COVER
NEOPRENE COVER
(FRONT WING)
(FRONT WING)
(REAR WING)
GREASE KIT
T30 TORX WRENCH
M6 X 40mm M6 X 25mm
SOCKETHEAD M6 X 16mm
PS 400
STABILIZER
0012 Ti
BARRELNUT M6
THREAD
COMPLETE FOIL SETUP
SKU: 120711033
SKU: 120711033
SKU: 120711033
SKU: 120711033
710 FUSELAGE
SKU: 19711015
MAST 92 cm
SKU: 18711010
SKU: 18711010
PANTASM
KITE 633
PHANTASM KITE 633 PACKAGE
After two years of meticulous and extensive research and
development, we are proud to introduce the ALL NEW
Phantasm 633. The Phantasm 633 is a high-performance
carbon freeride foil with tons of versatility in a lightweight
premium carbon construction. The Phantasm 633 is made
from super light, stiff and effcient high-modulus carbon,
but with a larger, lower aspect front wing that gives it tons
of lift, stability and dynamic performance at lower speeds.
At higher speeds, the Phantasm 633 will track and retain
its stability which aids in setting up for jibes and tacks, but
also will prevent over-foiling. The larger surface area of the
PFI 633 front wing, combined with the effciency of carbon
means it has a huge wind and speed range. The wing’s
unique inverted gull shape provides a crazy level of dynamic
carving control and a self-centering fight you have to feel
to believe. The Phantasm 633 package was built to provide
you with maximum free ride performance. With equal parts:
Speed, Stability, Lift, and Maneuverability, this is the most
predictable and user friendly foil on the market.
WRAPWITH TEFLON TAPE:
Wrap all bolt hardware in athin layer of Tefon Tape
layer of protection to prevent your bolts from corroding
and fusing with other components of your foil. Wrap
the tape tight so it feeds through the threads of the foil
properly without peeling off.
and fusing together. Don’t forget the inside of your front
wing. A cotton swab works well for this. Lanolin, or wool’s
wax, is a natural oil that acts as a lubricant and water
repellent. If you have an allergy to wool, be sure to take
precautions or use a different oil.
WWW.SLINGSHOTSPORTS.COM
CONTACT:
[email protected]
RIDER SERVICE IN THE US:
877.775.4832
INTERNATIONAL PHONE:
509.427.4950
SHIPPING ADDRESS:
390 EVERGREEN DRIVE, SUITE NORTH F
NORTH BONNEVILLE, WA USA 98639

1. Coat all screws with lanolin oil or marine-grade grease and wrap
with Teflon tape before assembling mast.
2. Connect the pedestal to the top of the mast with the two M8 x
40mm flathead screws.
3. Connect the fuselage adapter foot to the other end of the mast with
the two M8 x 45mm socket head screws.
PHANTASM ALUMINUM MAST
ASSEMBLY INSTRUCTIONS
STANDARD
WIDE

MAINTENANCE
It is imperative to clean and lubricate your foil regularly, especially
after use in salt water. This is true for all of your gear, but especially
for your foil. Following these simple steps on a regular basis will
minimize corrosion and prevent the components of your foil from
fusing together.
1. Coat all bolt hardware with Lanolin oil or a marine-grade
grease and wrap with Teflon tape before assembling your
foil.
2. Rinse your foil well after EVERY exposure to
salt water.
3. Regularly disassemble, clean and inspect
all components.
4. Regularly lubricate foil components and hardware at all
connection points. Use a general marine-grade grease or
Lanolin oil. Lubricate where components come together to
help prevent wear and corrosion.
5. Ensure all hardware is screwed firmly in place before each
use.
6. Be careful when handling your foil and use your protective
neoprene covers whenever possible.
Foiling comes with a unique set of challenges, risks and dangers.
Know your limits, know your gear, know the conditions and use
extra caution to keep yourselves and others safe in the water. Here
are a few basic safety precautions we recommend taking.
1. The use of a helmet, wetsuit, neoprene booties, and impact
vest are highly recommended, especially when learning, to help
protect yourself from impacts with your board and foil.
2. Check all foil screws and components before every session to
ensure all connections are tight, and components are in proper
working order.
3. Use extreme caution when foiling near other people or objects.
Give yourself and others a wide berth.
4. Do not foil in shallow water.
5. Pay extra attention to wind and water conditions; always err on
the side of caution.
6. Be aware that your foil will carry speed and drift on its own faster
and farther than a regular board.
SAFETY

WRAP WITH TEFLON TAPE:
Wrap all bolt hardware in a thin layer of Teflon Tape. This will be a
little tricky with the bolts covered in a layer of Lanolin oil/ or marine-
grade grease, but it acts as a second layer of protection to prevent
your bolts from corroding and fusing with other components of your
foil. Wrap the tape tight so it feeds through the threads of the foil
properly without peeling o.
LUBRICATE HARDWARE:
In a clean, sand-free area, carefully coat all bolt hardware, bolt
holes and ALL connection points with a layer of Lanolin oil or
marine-grade grease. Coat anywhere that parts touch each other
to prevent them from corroding and fusing together. Don’t forget
the inside of your fuselage to mast slot. A cotton swab works
well for this. Lanolin, or wool’s wax, is a natural oil that acts as a
lubricant and water repellent. If you have an allergy to wool, be
sure to take precautions or use a dierent oil.

CONTACT:
[e-mail]
RIDER SERVICE IN THE US:
877.775.4832
INTERNATIONAL PHONE:
509.427.4950
SHIPPING ADDRESS:
390 EVERGREEN DRIVE, SUITE NORTH F
NORTH BONNEVILLE, WA USA 98639
WWW.SLINGSHOTSPORTS.COM