SMART-AVI HDMV-16X-PLUS User manual

HDMV-16X-PLUS
Quick Start Guide
A full Manual can be downloaded from
www.smartavi.com/hdmv-16x-plus-v3/
16-Port HDMI KVM Multiviewer
TECHNICAL SPECIFICATIONS
VIDEO
Format Single-link 340MHz [10.2Gbps]
Maximum Pixel Clock 165 MHz
Input Interface (16) HDMI
Output Interface HDMI
Resolution 800 x 600 up to 1920 x 1200
DDC 5 volts p-p (TTL)
Input Equalization Automatic
Input Cable Length Up to 20 ft.
Output Cable Length Up to 20 ft.
USB
Signal Type USB 2.0, 1.1, and 1.0 w/ internal
hub
Input Interface (1) 3.5 mm Stereo Audio
Output Interface
(2) USB 1.1 Type A (female)
for keyboard/mouse
AUDIO
Input (2) 3.5 mm Stereo Audio
Output (1) 3.5 mm Stereo Audio
POWER
Power Requirements 12V DC, 3A power adapter with
center-pin positive polarity
ENVIRONMENT
Operating Temp 23 to 95°F (-5 to 35°C)
Storage Temp -4 to 185 °F (-20 to 85 °C)
Humidity Up to 95% (non-condensing)
CONTROL
Front Panel Push Buttons with LED indicators
RS-232 Via Serial @ 9600 bps
Hot Keys Via Keyboard
OTHER
Emulation Keyboard, Mouse and Video
WHAT’S IN THE BOX
PART NO. QTY DESCRIPTION
HDMV16X-PLUS 1 16-Port HDMI, USB Real-Time
Multiviewer and KVM Switch.
PS12VDC3A 1 12V DC, 3A power adapter with
center-pin positive polarity.
1 Quick Start Guide
NOTICE
The information contained in this document is subject
to change without notice. SMART-AVI makes no
warranty of any kind with regard to this material,
including but not limited to, implied warranties of
merchantability and fitness for particular purpose.
SMART-AVI will not be liable for errors contained
herein or for incidental or consequential damages in
connection with the furnishing, performance or use of
this material. No part of this document may be
photocopied, reproduced, or translated into another
language without prior written consent from
SMART-AVI, Inc.
Toll Free: (800) AVI-2123
Phone: [phone]
2455 W. Cheyenne Ave, Suite 112
North Las Vegas, NV 89032
smartavi.com
16-PORT HDMI 1080P
REAL-TIME MULTIVIEWER

HARDWARE INSTALLATION
1. Ensure that power is turned off or disconnected from the unit and the computers.
2. Use HDMI cables to connect the HDMI output ports from each computer to the correspond-
ing HDMI-I IN ports of the unit.
3. Use a USB cable (Type-A to Type-B) to connect a USB port on each computer to the respec-
tive USB ports of the unit.
4. Connect monitors to the HDMI-I OUT console ports of the unit using HDMI cables.
5. Connect a USB keyboard and mouse in the two USB console ports.
6. Optionally connect stereo speakers to the AUDIO OUT port of the unit.
7. Finally, power on the KVM by connecting a 12VDC power supply to the power connector, and
then turn on all the computers.
Note: You can connect up to 16 computers to the 16 port KVM.
SYSTEM CONTROL
There are three ways to control the
HDMV-16X-PLUS: Keyboard HotKeys, RS-232
Serial Commands, and Front Panel Buttons.
The settings for the serial connection are as
follows: Baud rate: 9600; Data Bits: 8; Pari-
ty: None; Stop Bits: 1; Flow Control: None.
The following commands can be used:
Command HotKey RS-232
Switch KVM [CT][CT]m[#]<CR> //M[#]<CR>
Video Only [CT][CT]i[#]<CR> //I[#]<CR>
Full Screen
Mode
[CT][CT]x1<CR> //X1<CR>
Quad Mode [CT][CT]x 2<CR> //X2<CR>
16X Mode [CT][CT]x 3<CR> //X3<CR>
Borders ON [CT][CT]b 1<CR> -
Borders OFF [CT][CT]b 0<CR> -
Status -//?? <CR>
Chart Key
[CT] = Ctrl
<CR> = Carriage Return (Enter Key)