SMART-AVI QKVM-DP User manual

QKVM-DP
Quick Start Guide
A full Manual can be downloaded from
www.smartavi.com/QKVM-DP/
TECHNICAL SPECIFICATIONS
VIDEO
Format DP
Maximum Pixel
Clock Single-link 340MHz [10.2Gbps]
Input Interface (4) DP
Output Interface DP
Resolution 800 x 600 up to 3840 x 2160
DDC 5 volts p-p (TTL)
Input Equalization Automatic
Input Cable Length Up to 20 ft.
Output Cable
Length Up to 20 ft.
USB
Signal Type USB 2.0, 1.1, and 1.0
Input Interface (4) USB Type B
Output Interface
(2) USB 1.1 Type A for KVM Devices
(2) USB 2.0 Type A Transparent
AUDIO
Input (4) 3.5 mm Stereo Audio
Output (1) 3.5 mm Stereo Audio
POWER
Power Require-
ments External 100-240 VAC/12VDC3A @ 36W
ENVIRONMENT
Operating Temp 32° to 104° F (0° to 40° C)
Storage Temp -4° to 140° F (-20° to 60° C)
Humidity 0-80% RH, non-condensing
CONTROL
Front Panel Push Buttons with LED indicators
RS-232 Via Serial @ 115200 bps
Hot Keys Via Keyboard
OTHER
Emulation Keyboard, Mouse and Video
WHAT’S IN THE BOX
PART NO. QTY DESCRIPTION
SM-QKVMDP-S 1
4-Port DP, USB 2.0 KVM Switch with
Multiview Preview Screen and Audio
Support.
PS12VD3A 1 12V DC, 2A power adapter with
center-pin positive polarity.
1 Quick Start Guide
NOTICE
The information contained in this document is subject
to change without notice. SMART-AVI makes no war-
ranty of any kind with regard to this material, includ-
ing but not limited to, implied warranties of merchant-
ability and fitness for particular purpose. SMART-AVI
will not be liable for errors contained herein or for
incidental or consequential damages in connection
with the furnishing, performance or use of this materi-
al. No part of this document may be photocopied,
reproduced, or translated into another language with-
out prior written consent from SMART-AVI, Inc.
Toll Free: (800) AVI-2123
Phone: [phone]
2455 W. Cheyenne Ave, Suite 112
North Las Vegas, NV 89032
smartavi.com
ULTRA-HD QUADRUPLE VIEW KVM
SWITCH 4-PORT DP, USB 2.0 KVM
SWITCH WITH MULTIVIEW PREVIEW
SCREEN TO VIEW ALL 4 VIDEO
SOURCES SIMULTANEOUSLY
4x2 Multiviewer KVM switch

HARDWARE INSTALLATION
1. Ensure that power is turned off or disconnected from the unit and the computers.
2. Use DP cables to connect the DP output ports from each computer to the corresponding DP-I IN ports of the
unit.
3. Use a USB cable (Type-A to Type-B) to connect a USB port on each computer to the respective USB ports of the
unit.
4. Optionally connect a stereo audio cable (3.5mm to 3.5mm) to connect the audio output of the computers to the
AUDIO IN ports of the unit.
5. Connect monitors to the DP-I OUT console ports of the unit using DP cables.
6. Connect a USB keyboard and mouse in the two USB console ports.
7. Optionally connect stereo speakers to the AUDIO OUT port of the unit.
8. Finally, power on the KVM by connecting a 12VDC power supply to the power connector, and then turn on all the
computers.
EDID LEARN
The QuadKVMDP has 3 preset EDIDs that can be trig-
gered from the front panel by pressing:
 Aand 1simultaneously will invoke IPG—1080p
 Aand 2simultaneously will invoke IPG - 4K
SYSTEM CONTROL
There are four ways to control the QKVM-DP: Key-
board HotKeys, RS-232 Serial Commands, OSD Menu
and Front Panel Buttons.
The settings for the serial connection are as follows:
Baud rate: 115200; Data Bits: 8; Parity: None; Stop
Bits: 1; Flow Control: None.
The following commands can be used:
Command HotKey RS-232
Switch KVM [CT][CT]m[#]<CR> //m[#]<CR>
Full Screen [CT][CT]f[#]<CR> //f[#]<CR>
PiP [CT][CT]p[a][b]
<CR>
//p[a][b]
<CR>
T-Quad [CT][CT]t[#]<CR> //t[#]<CR>
Quad [CT][CT]q<CR> //q<CR>
Audio Only [CT][CT]a[#]<CR> //a[#]<CR>
KM Only [CT][CT]c[#]<CR> //c[#]<CR>
USB Only [CT][CT]u[#]<CR> //u[#]<CR>
Learn EDID [CT][CT]e<CR> //e<CR>
SW Reset [CT][CT]r//r <CR>
Status Query N/A //?? <CR>
Chart Key
[CT] = Ctrl
<CR> = Carriage Return (Enter Key)
Command HotKey
OSD ON/OFF [CT][CT]o <CR>
OSD UP
↥(UP arrow)
OSD DOWN
↧(DOWN arrow)
OSD LEFT ↤(LEFT arrow)
OSD RIGHT ↦(RIGHT arrow)
OSD Enter [ENTER]
OSD Esc [ESC]
OSD MENU
Important: When in OSD Menu, all keyboard
and mouse functionality will be blocked from
the computer and only used for the OSD com-
mands. After exiting the OSD menu, all key-
board and mouse functionality will be restored.
NOTE: When entering one of the Function com-
mands, the Enter Key must be pressed for the
function to take effect