smart home INSTEON KeypadLinc V2 Dimmer Use and care manual

KeypadLinc™V2 Frame
and LED Color Change
Kit Replacement Steps
For Models:
KeypadLinc Color Frame Kits:
2401AL Almond
2401BK Black
2401BR Brown
2401GY Gray
2401L KeypadLinc V2 LED
Multi-Color Kit
Introduction
Depending on the kit purchased, the installer or end-
user can easily change the KeypadLinc V2 frame color
or the colors of the indicators under the buttons. The
frame and colored diffusers can be changed before or
after the KeypadLinc is installed in the wall. However,
it is easier to do the changes prior to installing the
KeypadLinc.
During the changeover process, the power and the
load may remain on and operating. There are no
dangerous voltages or unsafe areas while the button
plate is removed.
The color frame kit is compatible with older versions of
the KeypadLinc made after 2002. Earlier KeypadLinc
models with an all-plastic body cannot use the frame
kit.
Kit Contents
Frame Color Change Kits:
• Two same-color outside frames that replace the
white frame originally installed on a KeypadLinc
• Four extra screws
LED Color Change Kit:
• Eight small and two large tinted diffusers in each
of the following colors:
Green, Blue, Red, and Amber
• Four extra screws
Disassembling the KeypadLinc
1. If the KeypadLinc is installed in the wall, remove
the trim plate.
2. Remove the four Phillips screws that hold the
frame and buttons to the metal bracket.
3. Pull the entire frame straight away from the
switch. Also pull away the button plate assembly
(the plastic pieces the button caps are attached
to). You may have to wiggle the bottom of the
frame to get it free of the bottom Set Button.
Button
Plate
Center
Frame
Diffuser
Lenses
Button
Caps Frame

Frame Replacement Only
If only the frame is being changed to a different color,
the button plate and caps easily separates between
the old frame and onto the new one.
Please note:
No matter which color frame is used, the white button
plate and center frame will continue to be used. There
are not separate color parts to replace these pieces.
When paper labels are installed, users will not notice
the under-button structure or it color.
Colored Lens Diffusers
1. Remove the frame if not already done so.
2. Remove the plastic button caps by gently prying
under one corner of the cap.
3. Remove the existing diffuser.
4. Install the new tinted diffuser lens into the button
plate until the front surface is flush.
5. Snap the button cap back onto the button plate.
Installing the Frame onto the
Button Plate Assembly
1. Before installing the frame on to the button plate
assembly, take a moment to insure that both are
correctly aligned. Remove the frame if not already
done so.
2. On the backside of the frame, there are several
protrusions that will align up with the button plate.
3. Align the bottom of the frame with the two holes in
the bottom corners of the Button Plate.
4. Place the frame and button plate assembly onto the
KeypadLinc and reinstall the four screws.
Smarthome Limited Warranty
Smarthome warrants to the original consumer purchaser of this product that,
for a period of two years from the date of purchase, this product will be free
from defects in material and workmanship and will perform in substantial
conformity to the description of the product in this Owner's Manual. This
warranty shall not apply to defects or errors caused by misuse or neglect.
If the product is found to be defective in material or workmanship or if the
product does not perform as warranted above during the warranty period,
Smarthome will either repair it, replace it or refund the purchase price, at its
option, upon receipt of the product at the address below, postage prepaid, with
proof of the date of purchase and an explanation of the defect or error. The
repair, replacement, or refund that is provided for above shall be the full extent
of Smarthome's liability with respect to this product.
For repair or replacement during the warranty period, call Smarthome
customer service to receive an RA# (return authorization number), properly
package the product (with the RA# clearly printed on the outside of the
package) and send the product, along with all other required materials to:
Smarthome - ATTN: Receiving Dept.
16542 Millikan Ave. Irvine, CA 92606-5027
SwitchLinc, KeypadLinc, SignaLinc, LampLinc, PowerLinc, ToggleLinc,
BoosterLinc, ApplianceLinc, ControLinc, TesterLinc, FilterLinc,
ProbeLinc, TempLinc, TouchLinc, IR Linc, Insteon, SignaLinc RF, &
SmarthomeLive are trademarked by Smarthome, Inc.
© Copyright 2005 SmartHome, Inc. 800.SMART.HOME - 949.221.9200
rev 062105 www.smarthome.com
Button Plate
Frame alignment holes