Smart view DS-912F User manual

DVI
SPLITTER
(DS-912F)
1 In 2 Out
(DS-914F)
1 In 4 Out
(DS-918F)
1 In 8 Out
USER MANUAL V1.0
DS-912F / DS-914F
/ DS-918F
Package Contents-
1 Smart View DS-912F or DS-914F or DS-918F DVI splitter
1 user manual
1 power adapter DC 12V 600mA for DS-912F, DC 12V
1.25A for DS-914F or 1 AC power cord for DS-918F
2 rack rails, 8 screws for DS-914F only
2 rack rails, 6 screws for DS-918F only
Any thing missed, please contact with your vendor.
Introduction
Through the DVI (Digital Visual Interface) splitter DS-912F,
DS-914F, DS-918F you can use one PC to display
identical image on 2,4,8 monitors or even more.
DVI splitter is ideal for:
Test bench facilities
Data Center
Help desks
Features
Use PanelLink digital technology.
Supports high-resolution display up to UXGA
(25-165MHz).
Can be cascaded.
Compliant with the specification of DVI 1.0.
Supports DVI-I Single Link.
1U rack design for DS-914F, DS-918F.
Specifications
Function DS-912F DS-914F DS-918F
Video Input Connector
(DVI Female) 1
Video Output Connector
(DVI Female) 2 4 8
Max. Resolution 1600x1200 60Hz
Cable Distance
(Device to Monitor) 10 m (Max.)
Signal Type Standard DVI Signal
Power Adapter (Min.) DC 12V
600mA
DC 12V
1.25A
AC
100~240V
Housing Metal
Weight 490 g 985 g 2530 g
Dimensions (LxWxH)
mm 153x76x46 269x105x46 440x185x45
-1-
Technical Specifications
Input/Output Signal
Pin # Signal Pin # Signal
1 T.M.D.S Data 2- 16 Hot Plug Detect
2 T.M.D.S Data 2+ 17 T.M.D.S Data 0-
3 T.M.D.S Data 2/4 Shield 18 T.M.D.S Data 0+
4 T.M.D.S Data 4- 19 T.M.D.S Data 0/5 Shield
5 T.M.D.S Data 4+ 20 T.M.D.S Data 5-
6 DDC Clock 21 T.M.D.S Data 5+
7 DDC Data 22 T.M.D.S Clock Shield
8 Analog Vert. Sync 23 T.M.D.S Clock+
9 T.M.D.S Data 1- 24 T.M.D.S Clock-
10 T.M.D.S Data 1+
11 T.M.D.S Data 1/3 Shield C1 Analog Red
12 T.M.D.S Data 3- C2 Analog Green
13 T.M.D.S Data 3+ C3 Analog Blue
14 +5V Power C4 Analog Horz Sync
15 GND C5 Analog Ground
FRONT VIEW
1. Power LED
REAR VIEW
1. Input Power Jack
2. “DVI In” Port
3. “DVI Out” Port
*There are 2/4/8 out ports for DS-912F / DS-914F /
DS-918F.
-2-

Installation
1. Turn off the PC and monitors.
2. Connect the DVI male extension cable between the PC
and the “DVI in” port of splitter.
3. Connect the DVI male/female extension cables between
the monitors and the “DVI out” ports of splitter.
4. Connect the power cord and turn on the splitter.
5. Turn on the PC and monitors.
Note:
If you install the DDC monitor for the splitter, the rest of
monitors must be the same resolution as the DDC
monitor.
Operation for cascade:
1. The function to display identical image on more
monitors, you request to attach another splitter.
2. Connect the DVI male/female extension cable
between the former splitter of the “DVI out 1” port and
the latter splitter of the “DVI in” port.
Note:
Even though you are allowed to cascade the splitter with
varied ports, the image might become unstable if cascade
too many tiers of splitter.
P.S.: The example cascades the 2 and 4 ports splitters;
however, you can cascade the DVI Splitter with demanded
Port.
-3-
© C&C TECHNIC TAIWAN CO., LTD. All rights reserved.
Trademarks:
All the companies, brand names, and product names
referred to this manual are the trademarks or
registered trademarks belonging to their respective
companies.
-4-