TV One C2-1000 Series User manual

C2-1000 Series
Video Processor Operation Manual

C2-1000 SERIES OPERATION MANUAL

C2-1000 SERIES OPERATION MANUAL
Table of Contents
1 DISCLAIMER................................................................................................ 1
1.1 Regulatory Agency Acceptance...........................................................................1
1.2 FCC Statement....................................................................................................1
1.3 Manual Version Information.................................................................................2
1.4 Manual Copyright Notice.....................................................................................2
2 IMPORTANT SAFETY INSTRUCTION......................................................... 3
3 DEVICE SUMMARY ................................................................................... 13
3.1 Device Capabilities............................................................................................13
3.2 Device Features................................................................................................14
4 PRODUCT IMAGES ................................................................................... 15
5 FRONT PANEL CONTROLS...................................................................... 16
5.1 Button controls ..................................................................................................16
5.2 Multi-directional switch ......................................................................................17
5.3 Special button combinations and functions........................................................ 17
5.3.1 Locking front panel buttons & IR remote control................................................ 17
5.3.2 Factory Reset....................................................................................................17
5.3.3 Switching units between different resolutions (NTSC, PAL andDefault)............18
5.3.4 Forcing NTSC output resolution......................................................................... 18
5.3.5 Forcing PAL output resolution........................................................................... 18
5.3.6 Forcing default output resolution........................................................................18
6 AUDIO / VIDEO INPUTS AND OUTPUTS.................................................. 19
6.1 Computer & Video inputs................................................................................... 19
6.2 Computer & Video outputs................................................................................. 19
6.3 Audio inputs and outputs................................................................................... 20
7 INFRA-RED REMOTE CONTROL.............................................................. 21
8 MENU LAYOUT AND SETTINGS ADJUSTMENT...................................... 22
8.1 The High Level Menu Structure......................................................................... 23
8.2 Group Names and Descriptions......................................................................... 23
8.3 Items Associated with theAdjust outputs group................................................. 24
8.4 Items Associated with the Adjust windows group...............................................26
8.4.1 Extended scaling controls.................................................................................. 29
8.4.2 ‘Aspect adjust’ = ‘Advanced’..............................................................................30
8.4.3 ‘Aspect adjust’ = ‘Pixel’......................................................................................31
8.5 Items Associated with theAdjust keyers group.................................................. 31

C2-1000 SERIES OPERATION MANUAL
8.6 Edge Blend items within theAdjust keyers group ..............................................33
8.7 Items Associated with theAdjust sources group................................................ 34
8.7.1 Menu items common to all inputs......................................................................35
8.7.2 RGB Source Menu Items................................................................................... 37
8.7.3 CV & YC Source Menu Items............................................................................ 38
8.7.4 Testcard Source Menu Items.............................................................................38
8.8 Items associated with theAdjust transitions group.............................................39
8.9 Items associated with theAdjust resolutions group............................................40
8.10 Items Associated with theSystem group...........................................................43
9 RS232 PORT.............................................................................................. 47
9.1 Connection........................................................................................................ 47
9.2 Communications protocol.................................................................................. 47
10 RS232 / IP CONTROL SPECIFICATION.................................................... 48
10.1 Communication protocol basics.........................................................................48
10.2 Packet format....................................................................................................49
10.3 Function list.......................................................................................................51
10.4 Examples .......................................................................................................... 58
10.5 Reading and writing macros..............................................................................58
10.5.1 Reading a previously stored Macro...................................................................59
10.5.2 Writing to a macro.............................................................................................60
10.5.3 Run and Restore macros................................................................................... 60
11 COMMON OPERATIONS........................................................................... 61
11.1 Operation of the Keyer......................................................................................61
11.1.1 Preparation:.......................................................................................................61
11.1.2 Adjustment:.......................................................................................................61
12 EDGE-BLENDING SETUP......................................................................... 63
12.1 Introduction .......................................................................................................63
12.2 Edge-blending requirements..............................................................................64
12.3 Basic setup of the two projectors.......................................................................65
12.4 Connections to the scaler(s) and projectors.......................................................65
12.5 Initial setup........................................................................................................ 66
12.6 Edge-blending activation................................................................................... 67
12.7 Edge-blending overlap / size .............................................................................67
12.8 Edge-blending guide lines ................................................................................. 68
12.9 Alignment of projectors......................................................................................69
12.10 Gamma correction.............................................................................................71

C2-1000 SERIES OPERATION MANUAL
12.11 Brightness compensation.................................................................................. 71
12.12 Aspect ratio adjustment.....................................................................................72
12.13 Locking both outputs together........................................................................... 72
12.14 Other setup approaches.................................................................................... 73
13 WINDOWS CONTROL PANEL................................................................... 75
13.1 Opening screens...............................................................................................75
13.1.1 Selecting a serial port connection......................................................................75
13.1.2 Selecting an Ethernet connection......................................................................75
13.2 Connecting to a unit...........................................................................................76
13.3 Application menu’s............................................................................................78
13.3.1 File menu ..........................................................................................................78
13.3.2 Communications menu......................................................................................78
13.3.3 Tools menu .......................................................................................................79
13.3.4 Resolution menu...............................................................................................79
13.4 Scripting tool......................................................................................................79
13.5 Image Loader....................................................................................................80
13.5.1 Loading Testcards.............................................................................................81
13.5.2 Loading Logos...................................................................................................82
13.5.3 Maximum Image size – how large can my logo / Testcard be?..........................83
13.6 Resolution Editor...............................................................................................83
14 TROUBLESHOOTING AND TECHNICAL SUPPORT................................ 87
14.1 There is no picture on the Output......................................................................87
14.2 The image is shifted and not fully viewable........................................................87
14.3 The output resolutions no longer appear as expected.......................................87
14.4 There is excessive flicker on the Output............................................................88
14.5 The Output image is distorted............................................................................88
14.6 Some colors appear to be incorrect on the CV/YC output..................................88
14.7 How can I reduce color smearing on CV connections?......................................88
14.8 I can no longer adjust the Output image resolution............................................88
14.9 The picture on the video display is black and white........................................... 88
14.10 The picture on the video display is green...........................................................88
14.11 The RGB input is selected but the image is rolling or pink.................................89
14.12 The video signal from my DVD player does not appear to work......................... 89
15 RETURN PROCEDURE............................................................................. 90
15.1 Are you sure there's a fault?..............................................................................90
15.2 To return a unit for repair................................................................................... 90

C2-1000 SERIES OPERATION MANUAL
16 WARRANTY POLICY ................................................................................. 92
17 CONNECTOR PINOUTS............................................................................ 93
17.1 HD15 connector................................................................................................93
17.2 RS232 / D9 socket.............................................................................................93
17.3 4 Pin mini-DIN S-video connector (YC) input.....................................................93
17.4 Multi-way audio connector................................................................................. 94
17.5 UTP output........................................................................................................ 94
18 SPECIFICATIONS...................................................................................... 95
18.1 Video Inputs......................................................................................................95
18.2 Computer Input..................................................................................................95
18.3 Video Outputs (not present on all units).............................................................95
18.4 Computer Outputs.............................................................................................95
18.5 Audio input/output (certain models only)............................................................96
18.6 Locking/Mixing...................................................................................................96
18.7 Scaling / sampling / memory..............................................................................96
18.8 Warranty............................................................................................................96
18.9 Regulatory Compliance.....................................................................................96
18.10 Environmental...................................................................................................97
18.11 Power Requirement........................................................................................... 97
18.12 Control Methods................................................................................................97
18.13 Accessories Included.........................................................................................97
18.14 Mechanical........................................................................................................ 97
18.15 Optional Accessories.........................................................................................97
19 CONTACT INFORMATION......................................................................... 98

C2-1000 SERIES OPERATION MANUAL
1
1 DISCLAIMER
This product is intended for professional and/or home use. This product is not
intended for use in a medical environment and does not have the required
certifications for such use. Similarly, use aboard any aircraft or spacecraft while in
flight or as an adjunct to any surface, airborne or marine navigation system or any
offshore marine activity, including control of any watercraft, or any use similar to
those specifically herein mentioned is prohibited. Use in the aforementioned
circumstances would require additional testing and certification.
You have not become the owner of any software - you have merely purchased the
right to use the software. You may make one copy of the software for your own use.
Other copies will be deemed a breach of copyright.
No warranty is made either expressed or implied including but not limited to any
implied warranties of merchantability or fitness for a particular purpose. In no event
shall the supplier or manufacturer of this product be liable for errors found within, or
be liable for any direct, indirect or consequential damages or loss in connection with
the purchase or use of this hardware software or manual. The sole and exclusive
liability to the supplier and manufacturer regardless of the form of action shall not
exceed the replacement cost of the materials described herein.
By using this equipment you have indicated that you have agreed to the terms listed
above. If you do not wish to agree or the above terms are contrary to your conditions
of purchase you may return the equipment, unused, to your supplier. All trademarks
and copyrights are acknowledged. E&OE.
1.1 Regulatory Agency Acceptance
European ‘CE’ Mark Statement
Emissions: BS EN 61000-6-3:2001 (Generic Immunity Standard for Residential,
Commercial and Light Industrial)
Immunity: BS EN 61000-6-1:2001 (Generic Immunity Standard for Residential,
Commercial and Light Industrial)
1.2 FCC Statement
Class A Device: This equipment has been tested and found to comply with the limits
for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are
designed to provide a reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in
accordance with the Instruction Manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the
interference at his own expense.

C2-1000 SERIES OPERATION MANUAL
2
Caution: This equipment is intended for use in the manner prescribed in the
Instruction Manual. Any user changes or modifications not expressly approved by TV
One Multimedia Solutions could void the user’s authority to operate the equipment.
Connecting this equipment to external devices requires no specially shielded cabling
for FCC compliance. The Instruction Manual shows or describes the proper
connection of this equipment for operation that insures FCC compliance.
Direct all inquiries regarding FCC compliance to:
TV One Multimedia Solutions
1350 Jamike Drive
Erlanger, KY 41018
859.282.7303
859.282.8225 (Fax)
1.3 Manual Version Information
Version: 2.2
Release Date: July, 2008
1.4 Manual Copyright Notice
This Operation Manual is the intellectual property of TV One, ©2006, 2007, 2008. No
portion of this manual may be copied or reproduced in any manner or by any means,
including, but not limited to electronic and electro-mechanical, without the express
written permission of TV One.

C2-1000 SERIES OPERATION MANUAL
3
2 IMPORTANT SAFETY INSTRUCTION
To insure the best from this product, please read this manual carefully. Keep it in a
safe place for future reference.
To reduce the risk of electric shock, do not remove the cover from the unit.
No user serviceable parts inside. Refer servicing to qualified personnel.
2.1 Power and connections
This unit must be connected to a mains socket outlet with a protective earth
connection.
This unit is not disconnected from the AC power source as long as it is connected to
the wall outlet. The off state for this unit is called standby mode. In standby mode
the unit is designed to consume a reduced quantity of power compared to normal
operating modes.
When not using the unit for a long period of time, insure that the AC power cord is
disconnected from the wall outlet.
The AC wall outlet should be installed near to the unit and be easily accessible.
Do not plug in or attempt to operate an obviously damaged unit.
2.2 Water and moisture
To reduce the risk of fire and personal injury, operation of this device outdoors
and/or exposure to rain, water or excessive moisture is expressly prohibited.
The apparatus shall not be exposed to dripping or splashing and no objects filled
with liquids, such as vases, shall be placed on the apparatus.
2.3 General care
Do not force switches or external connections.
When moving the unit, disconnect the serial port connections first then the power
cable and finally the interconnecting cables to other devices.
Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this
may damage the unit. Use a clean dry cloth.
2.4 Location
Installation of this unit should be in a cool dry place, away from sources of excessive
heat, vibration, dust, moisture and cold.

C2-1000 SERIES OPERATION MANUAL
4
2.5 Ventilation
Slots and openings in the sides of the unit are provided for ventilation. To ensure
reliable operation, avoid obstruction of these openings and ensure the unit is
installed in a well-ventilated area.
2.6 Intellectual property
Some IC chips in this product include confidential and/or trade secret property.
Therefore you may not copy, modify, adapt, translate, distribute, reverse engineer,
reverse assemble or decompile the contents thereof.

C2-1000 SERIES OPERATION MANUAL
5
2 IMPORTANT: CONSIGNES DE SECURITE
Afin de tirer le meilleur de ce produit, merci de lire attentivement ce manuel. Gardez-
le dans un endroit sûr pour pouvoir le consulter à nouveau.
Afin de réduire le risque de choc électrique, ne retirez pas l’unité de sa protection.
Aucune pièce réparable par l’utilisateur à l’intérieur. Référez-vous à des personnes
qualifiées.
2.1 Alimentation électrique et connexions
Il faut brancher l'appareil sur une prise du secteur disposant d'une mise à la terre.
Cette unité n’est pas déconnectée de la source de courant électrique tant qu’elle est
connectée à la prise murale. Le mode éteint de cette unité est appelé mode de
veille. En mode de veille, cette unité est conçue pour consommer une quantité
réduite de courant par rapport aux modes normaux d’utilisation.
Lorsque vous n’utilisez pas l’unité pendant une longue période, assurez-vous que le
câble d’alimentation électrique est déconnecté de la prise murale.
La prise murale de courant doit être installée près de l’unité et aisément accessible.
Ne branchez pas et n’essayez pas d’utiliser une unité visiblement endommagée.
2.2 Eau et humidité
Pour réduire les risques d’incendie et de dommages corporels, l’utilisation de cet
appareil à l’extérieur et/ou son exposition à la pluie, l’eau ou une humidité excessive
est expressément interdite.
L’appareil ne doit pas être exposé aux gouttes ou aux éclaboussures et aucun objet
contenant de l’eau, comme par exemple un vase, ne doit être posé sur l’appareil.
2.3 Entretien général
Ne forcez pas les boutons ou connexions externes.
Lorsque vous déplacez l’unité, déconnectez d’abord les connexions de ports en
série puis le câble d’alimentation et enfin les câbles de connexion avec d’autres
appareils.
N’essayez pas de nettoyer l’unité avec des dissolvants chimiques ou des produits
nettoyants en aérosol, car cela peut endommager l’unité. Utilisez un chiffon propre et
sec.
2.4 Emplacement

C2-1000 SERIES OPERATION MANUAL
6
L’installation de cette unité doit se faire dans un endroit frais et sec, éloigné de
sources excessives de chaleur, de vibrations, de poussière, d’humidité et de froid.
2.5 Aération
Les rainures et les ouvertures sur les cotés de l’unité servent à l’aérer. Pour
permettre une utilisation sûre, évitez d’obstruer ces ouvertures et assurez-vous que
l’unité est installée dans un endroit bien aéré.
2.6 Propriété intellectuelle
Certaines puces IC dans ce produit contiennent des éléments propriétaires
confidentiels et/ou des secrets commerciaux. Vous ne devez donc pas copier,
modifier, adapter, traduire, distribuer, démonter, désassembler, ou décomposer leur
contenu.

C2-1000 SERIES OPERATION MANUAL
7
2 INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Para sacar el mejor provecho de este producto, léase este manual con
detenimiento. Guárdelo en un lugar seguro para poder hacerle referencia en el
futuro.
Para reducir el riesgo de calambre, no quite la cubierta del aparato.
No hay piezas utilizables dentro. Remítase todo mantenimiento a personal
cualificado.
2.1 Corriente y conexiones
Esta unidad debe estar conectada a una toma de corriente eléctrica con una
conexión a tierra de protección.
Mientras esté conectada a una toma de electricidad, el aparato seguirá conectado a
la fuente de corriente CA. A la posición de «off» de este aparato se le denomina
posición de espera. En la posición de espera, el aparato está diseñado a consumir
una cantidad reducida de electricidad en comparación con los modos de operación
normales.
Asegúrese de desconectar el cable de corriente CA de la toma de la pared cuando
no va a utilizar el aparato por un periodo largo de tiempo.
La toma CA de la pared ha de estar instalada cerca del aparato y debe ser
fácilmente accesible.
No enchufe ni intente operar un aparato que esté evidentemente dañado.
2.2 Agua y humedad
Para reducir el riesgo de fuego o de daños personales, se prohíbe la utilización de
este aparato en el exterior y/o su exposición a la lluvia, al agua o a atmósferas de
excesiva humedad.
El aparato no debe situarse cerca de zonas en las que haya riesgo de goteo o
salpicaduras. Tampoco deben colocarse objetos que contengan agua (jarrones, por
ejemplo) en el mismo.
2.3 Cuidado general
No forzar interruptores o conexiones externas.
Al mover el aparato, desconecte las conexiones del puerto en serie primero, luego el
cable de electricidad y finalmente los cables interconectados a otros aparatos.
No intente limpiar el aparato con disolventes químicos o productos de limpieza
aerosol, ya que podrían dañar el aparato. Utiliza un paño limpio y seco.

C2-1000 SERIES OPERATION MANUAL
8
2.4 Ubicación
Este aparato se debe instalar en un lugar seco y fresco, lejos de fuentes de calor
excesivas, la vibración, el polvo, la humedad y el frío.
2.5 Ventilación
El aparato viene provisto de ranuras y agujeros en los lados para la ventilación.
Para asegurar una operación eficaz, se debe evitar la obstrucción de estos agujeros
y también asegurar que el aparato se instale en una zona con adecuada ventilación.
2.6 Propiedad intelectual
Algunos chips con circuito integrado de este producto incluyen propiedad
confidencial y/o propiedad de secreto comercial. Por lo tanto queda prohibido copiar,
modificar, adaptar, traducir, distribuir, usar técnicas retroactivas, desmontar, o
recopilar los contenidos del mismo.

C2-1000 SERIES OPERATION MANUAL
9
2 WICHTIGE SICHERHEITSVORSCHRIFTEN
Lesen Sie diese Bedienungsanleitung bitte sorgfältig, um Ihr Produkt optimal nützen
zu können, und bewahren Sie sie zum späteren Nachschlagen an einem sicheren
Ort auf.
Entfernen Sie bitte keinesfalls die Abdeckung, um der Gefahr eines Stromschlags
vorzubeugen.
Im Inneren des Geräts befinden sich keine Teile, die vom Benutzer gewartet werden
können. Lassen Sie Wartungsarbeiten nur von Fachpersonal durchführen.
2.1 Stromversorgung und anschlüsse
Das Gerät muss an eine geerdete Netzsteckdose angeschlossen werden.
Solange das Gerät mit einer Steckdose verbunden ist, bleibt die Stromversorgung
aufrecht. Der Ausschaltzustand des Geräts wird als Standbymodus bezeichnet. Im
Standbymodus verbraucht das Gerät weniger Strom als in den üblichen
Betriebsarten.
Wird das Gerät über einen längeren Zeitraum hinweg nicht verwendet, ziehen Sie
bitte das Stromkabel aus der Steckdose.
Die Steckdose sollte sich in der Nähe des Geräts befinden und leicht zugänglich
sein.
Verbinden Sie ein offensichtlich beschädigtes Gerät keinesfalls mit einer Steckdose
und versuchen Sie auch nicht, es zu bedienen.
2.2 Wasser und feuchtigkeit
Um die Gefahr eines Brandes oder einer Körperverletzung zu verringern, ist es
ausdrücklich verboten, dieses Gerät im Freien in Betrieb zu nehmen und/oder es
Regen, Wasser oder hoher Feuchtigkeit auszusetzen.
Das Gerät darf keinen Tropfen oder Spritzern ausgesetzt werden und es dürfen
keine mit Flüssigkeiten gefüllte Behälter, wie Vasen, auf das Gerät gestellt werden.
2.3 Allgemeine pflege
Wenden Sie bei der Handhabung von Schaltern und Anschlüssen keine Gewalt an.
Beim Umstellen des Geräts entfernen Sie zuerst die seriellen Anschlüsse, dann das
Stromkabel und zum Schluss die Verbindungskabel zu anderen Geräten.
Versuchen Sie keinesfalls, das Gerät mit chemischen Lösungsmitteln oder
Sprayreinigern zu reinigen, da dies das Gerät beschädigen könnte. Verwenden Sie
ein sauberes, trockenes Tuch.

C2-1000 SERIES OPERATION MANUAL
10
2.3 Aufstellung
Das Gerät sollte an einem kühlen, trockenen Ort aufgestellt werden, fern von
übermäßiger Wärme, Vibrationen, Staub, Feuchtigkeit und Kälte.
2.5 Belüftung
Seitliche Schlitze und Öffnungen sorgen für die Belüftung des Geräts. Um die
ordnungsgemäße Belüftung zu gewährleisten, dürfen diese Öffnungen nicht verdeckt
werden. Sorgen Sie außerdem dafür, dass das Gerät an einem gut belüfteten Ort
aufgestellt wird.
2.6 Gewerbliches eigentum
Einige integrierte Schaltkreise in diesem Produkt enthalten vertrauliche
Informationen und/oder Betriebsgeheimnisse. Sie dürfen daher diese Inhalte nicht
kopieren, modifizieren, adaptieren, übersetzen, verteilen, rückentwickeln,
rückassemblieren oder dekompilieren.

C2-1000 SERIES OPERATION MANUAL
11
2 BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Lees deze handleiding zorgvuldig door om het beste uit uw product te halen. Bewaar
het op een veilige plek voor raadpleging in de toekomst.
Haal nooit het omhulsel van de eenheid af, dit om de kans op een elektrische schok
te verminderen. Maak het apparaat nooit open: er bevinden zich geen door de
gebruiker in te stellen onderdelen in het apparaat. Laat service en onderhoud over
aan een gekwalificeerde technicus.
2.1 Elektriciteit en aansluiting
Dit toestel moet worden aangesloten op een netcontactdoos met een
aardsluitingsbeveiliging.
Deze eenheid is niet van de wisselstroom voedingsbron gescheiden wanneer de
stekker nog in het stopcontact zit. Wanneer de eenheid uitstaat, staat deze nog in de
stand-by modus. In de stand-by modus vergt de eenheid minder stroom dan in de
normale "aan" modus.
Wanneer u de eenheid voor langere tijd niet gebruikt, zorg er dan voor dat de
stekker van het wisselstroomsnoer uit het stopcontact is getrokken.
Het wisselstroom stopcontact moet dichtbij de eenheid geïnstalleerd worden en
makkelijk toegankelijk zijn.
Als de eenheid duidelijk beschadigd is moet u deze nooit op het lichtnet aansluiten of
bedienen.
2.2 Water en vocht
Om het risiko op brand en persoonlijk letsel te beperken is het gebruik van dit
apparaat buiten en/of blootstelling aan regen, water of overdadige hoeveelheden
vocht uitdrukkelijk verboden.
Het apparaat mag niet worden blootgesteld aan druppels of bespatting en er mogen
geen objecten die gevuld zijn met vloeistoffen, zoals vazen, op het apparaat
geplaatst worden.
2.3 Algemeen onderhoud
Forceer schakelaars of externe aansluitingen nooit.
Bij verplaatsing van de eenheid, de seriële poortaansluitingen eerst loskoppelen, dan
de voedingskabel en als laatste de snoeren naar andere apparaten.
Probeer de eenheid nooit met chemische oplosmiddelen of schoonmaakmiddelen in
een spuitbus schoon te maken, omdat dit de eenheid kan beschadigen. Gebruik een
schone droge doek.

C2-1000 SERIES OPERATION MANUAL
12
2.4 Plaatsing
Deze eenheid moet geïnstalleerd worden op een koele droge plaats, uit de buurt van
bronnen van extreme hitte, vibraties, stof, vocht en kou.
2.5 Ventilatie
De sleuven en openingen aan de zijkant van de eenheid zijn voor ventilatie. Zorg er
voor dat de eenheid op een goed geventileerde plek geïnstalleerd wordt zodat deze
betrouwbaar werkt.
2.6 Intellectueel eigendom
Sommige IC chips in dit product bevatten vertrouwelijke informatie en/of
fabrieksgeheimen. U mag daarom de inhoud hiervan niet kopiëren, wijzigen,
aanpassen, vertalen, verspreiden, nabouwen, of decompileren

C2-1000 SERIES OPERATION MANUAL
13
3 DEVICE SUMMARY
3.1 Device Capabilities
The C2-1000 series uses the proprietary CORIO®2 Engine to perform its functions,
being the second generation of the successful CORIO®products. The CORIO®2
technology is a powerful toolset for any application requiring high quality video signal
conversion or image manipulation.
All units feature a single video processing and scaling engine, with some unit’s also
featuring video mixing, keying and fader capabilities.
These functions allow the flexibility for handling a wide range of inputs and outputs,
depending on the unit used.
All units are at one in the home and broadcast & display environments. The C2-1000
series offers a range of high-level image processing functions – with each model
designed to fulfill a particular need.
The following is a summary of the main types of product available in the C2-1000
series, as marked on the front of each unit:
Down Converter
Down converting an image is when a computer PC or HD input is inputted to the unit.
The input signal is then converted into a suitable signal which can then be displayed
for use on a video screen or television, such as composite video.
Down Converter PLUS
This unit has all the features of a Down Converter, but it also has the added facility to
superimpose the inputted computer image on top of an existing video signal. This is
achieved with the unit’s inbuilt facilities such as Keying, Picture in Picture (PIP), and
Fading.
Video Scaler
This unit allows for a standard television video signal, such as Composite Video, to
be input into the unit and then converted for use on a computer display. When using
this function you can switch back to the computer image by pressing a button. This is
known as bypass mode.
Video Scaler PLUS
Video Scaler PLUS has all the features of the Video Scaler unit, but with the added
facility of superimposing the converted video signal over the top of an existing
computer video signal. This is achieved by using the unit’s inbuilt features such as
Keying, Picture in Picture (PIP), Fading, and the facility to switch between overlaying
the foreground over the background and vice versa– background/foreground
priority.
Universal Scaler PLUS

C2-1000 SERIES OPERATION MANUAL
14
This ‘all in one’ converter facility combines the abilities of a Down Converter PLUS
and Video Scaler PLUS into one unit with added functionality for image
superimposition. This is achieved by using the units inbuilt features such as Keying,
Picture in Picture (PIP), Fading, and the facility to switch the between overlaying the
foreground over the background and vice versa – background/foreground priority.
3.2 Device Features
General Topography
4:4:4 RGB / YUV sampling provides full bandwidth color which allows precise keying
where included in the unit’s capabilities. This can be achieved through the
transparent (soft) keys on the front of the unit. Each unit’s video inputs accommodate
multiple video and computer signal formats and resolutions – see specifications at
end of manual for full details.
Ultimate flexibility
The C2-1000 series’ output signal format flexibility assures that the Native
Resolution of virtually any display can be matched. Because of the resolution
calculator (included in the Windows® Control Panel), even new resolutions can be
added to the unit. Signal parameter adjustments can be made for each video input
and are stored in individual non-volatile memories for retrieval once the unit’s power
has been removed. The Video Scaler units employ pixel adaptive motion
compensation to de-interlace fast moving images, and automatic 3:2 Pull-down
efficiently de-interlaces video from 24 fps NTSC film.
Simple Control
The unit can be controlled in various ways. One option is to control it from the front
panel using the transparent (soft) keys on the front of the unit. Another option would
be to control the unit from an infra-red remote control. It can also be controlled via
RS-232 using the Windows Control Panel.
The Windows Control Panel is available for download from our Internet site and
affords complete control of the unit and adds Scripting to facilitate long, complex
sequence of commands.
Finally, a hardware based switcher like the CORIO®console unit allows the user to
control the unit by mimicking a classic video switcher device.
Upgradeability
All C2-1000 units benefit from firmware upgradeability, thus reducing product
obsolescence by allowing the installation of the latest version of firmware. This not
only applies to the software used to control the unit, but also to the range of
resolutions stored inside the unit, the addition of new features, and upgrades to the
heart of the image processing hardware – the CORIO®2 scaling engine. See
http://www.tvone.com/support for more detail.