Smartenit Harmony P2 User manual

2014 Compacta International, Ltd. - Rev. 4/14
Harmony P2, iSmartenit, and Smartenit are trademarks of Compacta Intl. Ltd.
INSTEON is a registered trademark of SmartLabs, Inc. X10 is a registered trademark of X10.
[phone]
Technical Support
Smartenit.com
Quick Start Guide - Harmony P2 Model #6007C
Product Brief
Installation
For more information, please visit our Wiki
http://wiki.smartenit.com
Home Automation Gateway
Set-up
Ethernet PowerUSB Port
Your Harmony P2 is a stand-alone home automaon gateway
that gives you control of your ZigBee Home Automaon
(HA) devices from any computer or smart phone (Android
or iOS) connected to the Internet. INSTEON and X10
compability is available when an INSTEON PLM or USB
dongle is connected.
With the iSmartenit App, setup and control of your devices
has never been easier! Remote access to control your
devices on demand and/or set up automated schedules
based on a variety of condions can all be handled
via iSmartenit.
iSmartenit is available on either the Google Play or
the iTunes Stores. Search keyword “iSmartenit”.
1. Connect USB-CID to USB Port (for INSTEON/X10 support, connect to
EZIComm - sold separately)
2. Using the Ethernet cable provided, plug one end into your Ethernet
switch/router and the other end into your Harmony P2.
Note: If you need a longer cable, use a straight-through patch cable, not a cross-over cable.
3. Connect your Harmony P2 to power with the supplied 12V DC
As updates are made for the best user experience, please visit our Wiki to get the most recent “how-to” instrucons for using
the iSmartenit applicaon with your Gateway.
iSmartenit Wiki - hp://wiki.smartenit.com/index.php?tle=iSmartenit
Basics
1. Install iSmartenit app - available on iTunes, Google Play, or open web app at hp://app.smartenit.com
2. Create a user account to register your gateway for easy access from any iSmartenit applicaon (oponal)
3. Discover the Harmony P2 Gateway on your local network
4. Discover your smart devices
5. Directly control and monitor your smart devices
6. Set up Wizards to automate smart device control and monitoring
The Harmony SE must be installed indoors
1. Register
Register the device with your electric utility using the included
installation code and the instructions provided by the utility.
Each code is unique to a particular device, so please ensure the
provided numbers are entered correctly.
2. Connect network cable to Ethernet port and Internet router
3. Connect power supply
4. Point antenna upwards

2014 Compacta International, Ltd. - Rev. 4/14
Harmony P2, iSmartenit, and Smartenit are trademarks of Compacta Intl. Ltd.
INSTEON is a registered trademark of SmartLabs, Inc. X10 is a registered trademark of X10.
iSmartenit Application Interface Basics
Adding devices
Step 1 Step 2 Step 3
Click on the Default Area icon to
open devices menu for this area.
Other Areas can be added here by
clicking the “+” icon. Areas can
be used to organize devices into
sub-categories.
Click on the “New Coordinator”
device to get to the gateway
conguraons.
Click on the “Start Network”
buon to acvate the Gateway’s
automaon network.
Then click “Start Discovery”
to enable the Gateway to add
devices. The 250 second (editable)
countdown will begin.
Click the “Back” buon to get
back to the devices menu.
ZigBee devices: Ensure devices are
searching for an open network to join.
INSTEON devices: Put devices in link
mode to add them to the Gateway.
X10 devices: Click on “+” icon to “Add a
device manually” and select “X10” from
the picker, and select the X10 address,
then click the disk icon to save.
The “+” buon will also allow you to
“Discover Devices” again when the me
has expired.
Step 4
As your devices join the network,
they will get populated in the
device menu for the Default Area.
From this menu, you’ll be able
to control On/O and Dimming
devices as well as see the status of
devices (Ex. Energy Consumpon,
Temperature, Humidity, Load
State, etc...)
Adding a Wizard
Step 1 Step 2 Step 3
Wizards are macros that can
be set to automacally control
devices on your network based
on me or the state of other
devices.
Click on the Wizards buon to
get to the Wizards menu.
Once in the Wizards menu, click
the “+” icon to add a new Wizard.
The next screen will allow you
give the Wizard a name and add
condions and eects.
Click on the “+” icon under the “When”
secon to add a condion for when the
Wizard will trigger a desired acon.
The “When” can be set up to trigger
based on me of day, day of week, status
of another device, or all of the above.
Click the disk icon to save when nished.
Step 4
Click on the “+” icon under the “Do
this” secon to add an eect that
will be triggered when the “When”
condion is met.
Select a device and the acon to
take place when the condion is
met.
Click the disk icon to save when
nished.
[phone]
Technical Support
Smartenit.com
For more information, please visit our Wiki
http://wiki.smartenit.com
NOTE: Visit hp://wiki.smartenit.com/index.php?tle=ISmartenit for more info.