Allnet ALL7008 User manual

ALLWALL
ALL7008

2

Quick Install Guide
Express-Setup
Version 12 2007
3

4

Hardware Configuration
Hardware Description:
Power LED: Illuminates solid green when ALL7008 is first
powered up. Start up takes up to one minute to complete.
Status LED: When LED light start glittering, it means the
system is under the status of booting. Around two minutes
when the LED light stop glittering, it means the system is
booting successful.
WAN 1/2 Port: To connect to the external router, DSL modem,
or Cable modem.
LAN Port: Connect to the intranet PCs.
DMZ Port: Connect to the company’s server(s).
Console Port: 9-pin serial port connector for checking
ALL7008 system setting and restore to the factory setting.
5

Software Configuration
STEP 1﹒Connect both the Administrator’s PC and the LAN port of ALL7008
to a hub or switch. And use a web browser to display the
configurations of the ALL7008 (such as Internet Explorer or
Netscape). The default IP address of ALL7008 is http://192.168.1.1
with a subnet mask of 255.255.255.0. Therefore, the IP address of
the Administrator PC must be in the range between 192.168.1.2–
192.168.1.254
STEP 2﹒After the new IP of Administrator’s PC take effect, enable IE or
Netscape and connect to http://192.168.1.1 and it can use browser
to set up the parameter ofALL7008.
The following table is a list of virtual IP addresses. These addresses may not use
WAN Real IP address.
10.0.0.0 ~ 10.255.255.255
172.16.0.0 ~ 172.31.255.255
192.168.0.0 ~ 192.168.255.255
6

STEP 3﹒A pop-up screen will appear and prompt for a username and
password. A username and password is required to connect to
ALL7008. Enter the default login username and password of
Administrator (FigureS-1).
Username: admin
Password: admin
Click OK.
FigureS-1 Login WebUI
STEP 4﹒After entering the username and password, select Interface on the
left menu and click on LAN. (FigureS-2)
LAN: enter IP address 192.168.1.1
Netmask: 255.255.255.0
Click OK.
FigureS-2 IPAddress and Netmask Setting
STEP 5﹒If new LAN IP Address is not 192.168.1.1, after clicking on OK, it
must change the System Manager’s IP Address to be at the same
subnet range as the new LAN IP. And enter the new LAN IP in
browser website field and reconnect ALL7008 again.
7

STEP 6﹒After entering to the main system of ALL7008, select Interface on the
left menu and click on WAN. (Figure S-3)
FigureS-3 WAN 1/2 Interface
STEP 7﹒WAN Interface 1 / 2: select the WAN 1/2 that needs to be set and
click Modify. Enter the IP address provided from ISP. (Figure S-4)
Figure S-4 WAN IPAddress and Netmask Setting
8

STEP 8﹒If Mail Server is in DMZ, it needs to set DMZ Interface; If Mail Server
is set in WAN, and then skips Step 8
Select Interface on the left menu and click DMZ function.
DMZ Interface: Select DMZ_TRANSPARENT
Click OK. ALL7008 will reboot again. It takes about 2 minutes to
reboot. When the LED light stop glittering, it means reboot
successfully and can enter WebUI again. (FigureS-5)
FigureS-5 DMZ WebUI
STEP 9﹒Click on System function and click on Date/Time function in
Configure.
STEP 10﹒Enter the following setting in Date/Time setting:
Select Enable synchronize with an Internet time Server.
Set offset +8 hours from GMT
Enter the Server IP/Name: 133.100.9.2
Enter Update system clock every 360 minutes.
Click OK. (FigureS-6)
FigureS-6 Date/Time Setting
9

STEP 11﹒Click on Policy on the left function menu and then click on
Outgoing from the sub-function list.
STEP 12﹒Click New Entry (Figure S-7)
STEP 13﹒At Add New Policy WebUI, enter the following information:
Source Address – Select “Inside_Any”
Destination Address – Select “Outside_Any”
Action: Select “PERMIT ”
Click OK
Figure S-7 Add New Policy Setting
STEP 14﹒If ALL7008 access control function is being required, please refer to
Policy and Address to add some settings.
10