Smartlock Digital SMARTPOINT SMARTLINC II 9160 Operation instructions

USER OPERATING INSTRUCTIONS
SMARTPOINT SMARTLINC II
Biometric Recognition Safe Locking System
9150
9160
CHANGING YOUR CODE - USER
ALWAYS PERFORM THIS OPERATION WITH THE DOOR OPEN
AVAILABLE FEATURES
USER CODE
+Open Lock
+Change Code
+Set Immediate Time Lock, if enabled
+Time Lock Extension, if enabled
+Four (4) consecutive invalid codes initiates ve-minute delay
period. Two additional invalid codes will begin another ve-
minute delay.
+Repeated audio and visual signal (LCD readout and repeated
beeping) during opening indicates back-up battery is low and
should be replaced.
The duress feature is available if the unit has been connected to an alarm system via a battery/
alarm box. To use simply enter your code with the last number either + or - 1 or use the duress
nger print, if enrolled.
Example: Existing code (2-9-2-9-2-9)Duress code (2-9-2-9-2-8 or 2-9-2-9-2-0)
+Double signal (LCD readout and unit beeps) indicates entry is
valid or accepted
+Triple signal indicates invalid or not accepted
+Immediate Time Lock (From now until next available open
period)
+Time Lock Open Period Extension (Max. two (2) hours), if
enabled
+Up to Five
+Requires the presence of two users to open
+Programmable on each lock
- Delay Period: 1 - 99 minutes
- Open Period: 1 - 19 minutes
+Two Time Delays Can Run At Once
MULTIPLE LOCKS
DUAL CODE
WRONG TRY PENALTY
LOW BATTERY WARNING
USING DURESS
AUDIO AND VISUAL SIGNAL
TIME LOCK
TIME DELAY
1. Press any key to power up SMARTPOINT.
+ Display will show either “ENTER CODE” or SELECT LOCK” when two or more locks are installed.
2. Select lock if two or more locks are installed.
3. Enter “zero” six times
4. Enter existing six (6) digit code one time.
5. Enter NEW six (6) digit code two times (and scan nger, if set-up, after 2nd entry).
+ If a valid code is entered, display will show “CODE CHANGED”
6. Test lock operation several times before closing the door.
7. If code update verication does not appear the old code is still valid. Wait 30 seconds and repeat
steps 1 - 6
SELECT LOCK
XX
ENTER LOCK
X-X-X-X-X-X
OLD CODE
X-X-X-X-X-X
NEW CODE
X-X-X-X-X-X
CONFIRM NEW
X-X-X-X-X-X
CODE CHANGED
CONFIRM CODE
NOT MATCH
This system is available with or without biometric identication ability. If using the SMARTLINC II, without biometric ability, please disregard
any reference, in these instructions, to ngerprints. The functionality of the two systems are identical except for the use of ngerprints
for identication.
SMARTPOINT SMARTLINC II
V1.0_9102 | Division of Davcor Group Pty Ltd | www.smartlock.com.au | www.smartlock.co.nz | Page 1

USER OPERATING INSTRUCTIONS
SMARTPOINT SMARTLINC II
Biometric Recognition Safe Locking System
OPENING THE LOCK (WITH FINGER ONLY ACCESS WITHOUT TIME DELAY)
OPENING THE LOCK (WITHOUT TIME DELAY)
1. Press any key to power up SMARTPOINT.
+ Display will show either “ENTER CODE” or SELECT LOCK” when two or more locks are installed.
2. Select lock if two or more locks are installed, display will show “P TO SCAN, OK FOR CODE”.
3. Press P key, display will show “SCAN YOUR FINGER”.
+ If a valid ngerprint is entered, display will show “LOCK = 1, OPEN!”.
+ If Lock is set with Open Oset, the display will show “LOCK = #, OFFSET = ##”, and will show the
counting sequence to the Oset.
4. Open the Door within 3 seconds.
+ Before power-o, display will show current date and time.
+ If an invalid ngerprint is scanned or the ngerprint was not placed directly on the scanner, the
display will show ”FINGERPRINT ERROR!”.
+ Display will power-o after 30 seconds of non-operation.
1. Press any key to power up SMARTPOINT.
+ Display will show either “ENTER CODE” or “SELECT LOCK” when two or more locks are installed.
2. Select lock if two or more locks are installed.
3. Enter a valid 6 (six) digit User Code (and scan nger, if set-up)
+ If a valid code/nger is entered, display will show “LOCK = 1, OPEN!”.
+ If Lock is set with Open Oset, the display will show “LOCK = #, OFFSET = ##”, and will show the
counting sequence to the Oset.
4. Open the Door within 3 seconds.
+ Before power-o, display will show current date and time.
+ If and invalid code is entered, display will show “NOT VALID USER!”.
+ If an invalid ngerprint is scanned or the nger was not placed directly on the scanner, the display
will show ”FINGERPRINT ERROR!”.
+ Display will power-o after 30 seconds of non-operation.
SELECT LOCK
XX
P TO SCAN
OK FOR CODE
SCAN
YOUR FINGER
LOCK = 1
OPEN!
FINGERPRINT
ERROR!
NOTE: IF THERE IS A LOCK SET TO AUTO OPEN - In a multiple lock system you can set an outer door lock to AUTO OPEN. This will allow the user (if
authorised) to open the inner compartment lock and have the outer door lock automatically open. The AUTO OPEN lock always opens rst.
NOTE: IF THERE IS A LOCK SET TO AUTO OPEN - In a multiple lock system you can set an outer door lock to AUTO OPEN. This will allow the user (if
authorised) to open the inner compartment lock and have the outer door lock automatically open. The AUTO OPEN lock always opens rst.
NOTE: If there is a user who ngerprint is unable to be read, by pressing OK they can enter their code and scan their print. The
system will do a one-to-one match.
SELECT LOCK
XX
ENTER LOCK
X-X-X-X-X-X
LOCK = #
OFFSET = ##
LOCK = 1
OPEN!
NOT VALID USER!
FINGERPRINT
ERROR!
OPENING THE LOCK (WITH TIME DELAY)
1. Press any key to power up SMARTPOINT.
+ Display will show either “ENTER CODE” or SELECT LOCK” when two or more locks are installed.
2. Select lock if two or more locks are installed.
3. Enter a valid 6 (six) digit User Code (and scan nger, if set-up)
+ If Time Delay has been set, display will show “STARTING, TIME DELAY” and then “LOCK = #, DELAY
MM:SS”
+ Counting is updated every second, if displayed.
+ Press “P” to abort Time Delay, display will show “CANCEL, TIME DELAY?” Press OK, display will
show, “TIME DELAY, CANCELLED”.
+ After Time Delay has elapsed, the display will show “P TO SCAN, OK FOR CODE” and then “#X
MM:SS, x-x-x-x-x-x” (open window counting time).
4. During the open window, enter a valid code (and scan nger, if set-up) to open.
+ If a valid code is entered, display will show “LOCK = 1, OPEN!”.
SELECT LOCK
XX
ENTER LOCK
X-X-X-X-X-X
STARTING
TIME DELAY
LOCK = #
DELAY MM:SS
CANCEL
TIME DELAY?
V1.0_9102 | Division of Davcor Group Pty Ltd | www.smartlock.com.au | www.smartlock.co.nz | Page 2

P TO SCAN
OK FOR CODE
#1 MM:SS
X-X-X-X-X-X
LOCK = 1
OPEN!
NOT VALID USER!
FINGERPRINT
ERROR!
NOTE: During the Open Window the unit will beep 2 times every 10 seconds.
2nd CODE
X-X-X-X-X-X
SELECT LOCK
XX
FINGERPRINT
ERROR!
ENTER LOCK
X-X-X-X-X-X
LOCK = 1
OPEN!
NOT VALID USER!
OPENING THE LOCK (WITH DUAL CODE - NO TIME DELAY)
1. Press any key to power up SMARTPOINT.
+ Display will show either “ENTER CODE” or SELECT LOCK” when two or more locks are installed.
2. Select lock if two or more locks are installed.
3. Enter a valid 6 (six) digit User Code (and scan nger, if set-up)
4. Enter a 2nd valid 6 (six) digit code (and scan nger, if set-up)
+ If a valid code is entered the LCD will display “LOCK = 1, OPEN!”.
5. Open the Door within 3 seconds.
+ Before power-o, display will show current date and time.
+ Invalid code will prompt LCD to display “NOT VALID USER”.
+ If an invalid ngerprint is scanned or the nger was not placed directly on the scanner, the display
will show ”FINGERPRINT ERROR!”.
+ Display will power-o after 30 seconds of non-operation.
5. Open the Door within 3 seconds.
+ Before power-o, display will show current date and time.
+ If and invalid code is entered, display will show “NOT VALID USER!”.
+ If an invalid ngerprint is scanned or the nger was not placed directly on the scanner, the display
will show ”FINGERPRINT ERROR!”.
+ Display will power-o after 30 seconds of non-operation.
+ If using the Time Delay Override, enter USER code and touch nger, if set-up.
OPENING THE LOCK (WITH DUAL CODE AND TIME DELAY)
1. Press any key to power up SMARTPOINT.
+ Display will show either “ENTER CODE” or SELECT LOCK” when two or more locks are installed.
2. Select lock if two or more locks are installed.
3. Enter a valid 6 (six) digit User Code (and scan nger, if set-up)
+ If Time Delay has been set, display will show “STARTING, TIME DELAY” and then “LOCK = #, DELAY
MM:SS”
+ Counting is updated every second, if displayed.
+ Press “P” to abort Time Delay, display will show “CANCEL, TIME DELAY?” Press OK, display will
show, “TIME DELAY, CANCELLED”.
+ After Time Delay has elapsed, the display will show X MM:SS, x-x-x-x-x-x” (open window counting
time).
4. During the open window, enter a valid code (and scan nger, if set-up) , display will show “ENTER
CODE, X-XX-X-X-X”.
+ If a valid code is entered, display will show ““2ND CODE, X-X-X-X-X-X”.
5. Open the Door within 3 seconds.
+ Before power-o, display will show current date and time.
+ If and invalid code is entered, display will show “NOT VALID USER!”.
+ If an invalid ngerprint is scanned or the nger was not placed directly on the scanner, the display
will show ”FINGERPRINT ERROR!”.
+ Display will power-o after 30 seconds of non-operation.
+ If using the Time Delay Override, enter USER code and touch nger, if set-up.
SELECT LOCK
XX
ENTER LOCK
X-X-X-X-X-X
STARTING
TIME DELAY
LOCK = #
DELAY MM:SS
CANCEL
TIME DELAY?
USER OPERATING INSTRUCTIONS
SMARTPOINT SMARTLINC II
Biometric Recognition Safe Locking System
NOTE: During the Open Window the unit will beep 2 times every 10 seconds.
#1 MM:SS
X-X-X-X-X-X
ENTER LOCK
X-X-X-X-X-X
2ND CODE
X-X-X-X-X-X
LOCK = 1
OPEN!
V1.0_9102 | Division of Davcor Group Pty Ltd | www.smartlock.com.au | www.smartlock.co.nz | Page 3

5.0 Time Menu
Time Menu allows the USER access to following functions if programmed during initial lock set-up:
NOTE: These functions are available only if one or more opening periods are stored in Time Lock Standard Week. Please see
Master Operating Instructions for more information on setting this up.
+Immediate Time Lock - Immediate Closing until the next opening period.
+Extension Time Lock (Active only if programmed through the PC) - Increase the open period. [30 Minutes at a time for a maximum of
two (2) hours.]
TIME MENU
2nd CODE
X-X-X-X-X-X
SELECT LOCK
XX
FINGERPRINT
ERROR!
ENTER LOCK
X-X-X-X-X-X
LOCK = 1
OPEN!
NOT VALID USER!
TIME MENU - IMMEDIATE TIME LOCK
Available only if programmed during initial lock set-up
1. Press any key to power up SMARTPOINT.
+ Display will show either “ENTER CODE” or SELECT LOCK” when two or more locks are installed.
2. Hold down “9” button, display will show “ACCESS, TIME MENU” then “ENTER CODE, X-X-X-X-X-X”.
3. Enter User code (and scan nger, if set-up).
+ If a valid code is entered, the display will show “IMMEDIATE TIME LOCK?”
4. Press OK to continue, display will show ”SELECT, T.L. SET = 1”
5. Press OK to continue, display will show “Do You CONFIRM?”
6. Press “OK” a 2nd time to conrm.
+ If the list of Time Lock Standard Week is empty, the function is unavailable and the display will
show ”LOCK = #, NOT VALID.”
USER OPERATING INSTRUCTIONS
SMARTPOINT SMARTLINC II
Biometric Recognition Safe Locking System
1. Press any key to power up SMARTPOINT.
+ Display will show either “ENTER CODE” or SELECT LOCK” when two or more locks are installed.
2. Hold down “9” button, display will show “ACCESS, TIME MENU” then “ENTER CODE, X-X-X-X-X-X”.
3. Enter User code (and scan nger, if set-up).
+ If a valid code is entered, the display will show “IMMEDIATE TIME LOCK?”
4. Press “P” to select next function, display will show ”EXTENSION TIME”
5. Press “OK” to continue, display will show ”SELECT LOCK, NUMBER = #”
6. Press “OK” to conrm, display will show “EXTENT. TIME, 0 MIN”.
7. Press “P” to change the extension time in 30 minute increments. Press P once for 30 minutes, twice
for 60 minutes, three times for 90 minutes and four time for 120 minutes.
8. Press “OK” to conrm, display will show “EXTENSION SET!.”
+ If the list of Time Lock Standard Week is empty, the function is unavailable and the display will
show ”LOCK = #, NOT VALID.”
IMMEDIATE
TIME LOCK?
SELECT LOCK
XX
EXTENT. TIME
0 MIN
EXTENSION SET!
ENTER LOCK
X-X-X-X-X-X
EXTENSION TIME
SELECT
T.L. SET = 1
TIME MENU - TIME LOCK EXTENSION
Available only if programmed during initial lock set-up
To access the TIME MENU
NOTE: Time Lock Extension can only be implemented one time per time lock period. For example, if the extension needed is 60 minutes,
it must be entered as 60 minutes, not 30 minutes and then part way through the 30 minute extension extend it another 30 minutes.
CAUTION: If a mistake is made inserting Time and Date values, DO NOT CONFIRM. Instead, press P to cancel and repeat the steps
from the beginning.
V1.0_9102 | Division of Davcor Group Pty Ltd | www.smartlock.com.au | www.smartlock.co.nz | Page 4