Resolution RE152 User manual

RE152_GE-Compat_PIN-Pad Page 1 of 3 29-Oct-14
24-Hour Tech Support Line: [phone]
www.ResolutionProducts.com
RE152 GE-Compatible PINpad™
Features
• Secure, 4-digit Code to disarm
• 1-button arming
• Red/Green LED arming eedback
• Small, yet com ortable keypad
• Mounts on wall via VHB® tape, or screws
• Secure or carrying in purse or mounting on car visor
• Strong, reliable RF signal.
• 4-6 year battery li e on CR2032 battery.
Key Instructions
• Enroll as a Key Fob.
• Code programming
De ault access code is “1234”.
To change access code: Do these steps within 4 seconds
1. Enter current 4-digit access code.
2. Press and hold the “1” and “3” keys simultaneously.
(a ter 3 seconds, Red LED will be lit)
3. Enter new 4-digit access code.
(the Green LED will be lit)
Note new access code . BAD GUY CANNOT RESET CODE.
So it must be recorded and remembered!
• Enrolling:
1. Re er to the GE control unit installation manual.
2. Put the control panel in RF Learning mode.
• Press both the Stay & Away buttons simultaneously
or 3 seconds.
3. …Or i using a Downloader in ID entry mode
• Enter the Download ID the device
(located on a label on the unit’s back or in unit).
Operation
PINpad
Button Panel Action LED
Stay
ARM STAY
lashes double red
Away
ARM AWAY
lashes double red twice
PIN Code
DISARM
lashes double green
Stay + Away
PANIC ALARM
lashes red 8 times
RE152_GE-Compat_PIN-Pad Page 2 of 3 29-Oct-14
24-Hour Tech Support Line: [phone]
www.ResolutionProducts.com
Pictures
Battery Replacement
CR2032 Battery
+ Terminal up
Insert Screwdriver
here
to open
Red/Green
Status LED
Shows command sent
Stay + Away
=
Panic (Enroll)
TO CHANGE PIN CODE:
Current 4-digit access code, and then…
1 + 3 simultaneously  Red LED,
and then…
Enter New Code

RE152_GE-Compat_PIN-Pad Page 3 of 3 29-Oct-14
24-Hour Tech Support Line: [phone]
www.ResolutionProducts.com
Speci ications
Not supervised.
Replacement Battery: CR2032 Lithium / Manganese Dioxide
Temperature Range: 0F to 120F
Housing dimensions: 2x2.25x0.33 inches
1-way RF: Does not receive panel status
Speci ications subject to change without notice.
Notices
“GE”, “Honeywell”, “DSC”, “2GIG” and “Napco” are trademarks owned y General Electric
Company, Honeywell International Inc., Tyco Safety Products Canada LTD, 2GIG Technologies
Inc., and NAPCO Security Systems, Inc., respectively.
Resolution Products, Inc. products will function with one of either GE, Honeywell, DSC or
Napco systems. However, no Resolution product is produced y, endorsed y, nor is officially
associated with GE, Honeywell, DSC or Napco. Resolution recommends verifying proper
enrollment and operation, per control panel installation instructions, at installation.
Warranty
Resolution Products, Inc. will replace products that are defective in their first five (5) years.
FCC Notice
This device complies with Part 15 of the FCC rules. Operation is su ject to the
following two conditions:
This device may not cause harmful interference.
This device must accept any interference that may e received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved y the Resolution Products, Inc. could
void the user's authority to operate this equipment.
FCC ID: U5X-RE152
IC Notice
This device complies with Industry Canada license-exempt RSS standard(s). Operation is
su ject to the following two conditions:
(1)This device may not cause interference, and
(2)This device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applica les aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1)l'appareil ne doit pas produire de rouillage, et
(2)l'utilisateur de l'appareil doit accepter tout rouillage radioélectrique su i,
même si le rouillage est suscepti le d'en compromettre le fonctionnement.
IC: 8310A-RE152