SMC Networks DM Series User manual

Multi-connector
Series DM
No. of Connecting Tubes: 6, 12
Specifications
Principal Parts Material
PAT.
Model
Socket
Socket case
Clamp bolt
U-shape seal
Tight seal.
Plug case
Plug
Stopper (with expander)
Clamp ring
Holder
Plate
Spacer
Cover
The use of the multi-
connector enables panel
mount connections with
other apparatus and can
provide the reliability of
one-touch installation and
removal of multi-tubes
(nylon, polyurethane).
As a result, separate
transportation of panel,
machinery, and backup
units is made easy.
One-touch installation and
removal
Employs the unique built-in keying
mechanism which provides one-touch
installation and removal capability even
in hard to see locations. In addition, it
prevents installation mistakes when re-
connecting.
Installation processes are
reduced considerably
As compared with the use of many bulk-
head unions, this installation is very
easy and installation time is reduced
considerably.
Reliable tube retaining force
This construction mechanism enables
clamping and unclamping of every tube
in use by one operation and can provide
a reliable tube retaining force.
No. of connecting tubes
2 types—6 tubes & 12 tubes.
DM6
DM12
Model
No. of
connecting tubes
Applicable tubing
Accessory
(Option)
Multi-connector Polyurethane
—
TU0425
—
TU0425
—
TU0604
TU0604
—
Soft nylon
—
TS0425
—
TS0425
—
TS0604
TS0604
—
Nylon
T0425
T0403
T0604
T0403
T0604
T0645
T0645
T0425
6
12
DM-C-6
DM-C-12
DM6-04N
DM6-04NU
DM6-06N
DM6-06NU
DM12-04N
DM12-04NU
DM12-06N
DM12-06NU
Plug side
DM6P-04N
DM6P-04NU
DM6P-06N
DM6P-06NU
DM12P-04N
DM12P-04NU
DM12P-06N
DM12P-06NU
Socket side
DM6S-04N
DM6S-04NU
DM6S-06N
DM6S-06NU
DM12S-04N
DM12S-04NU
DM12S-06N
DM12S-06NU
Fluid Air
1.0 MPa
–5 to 60°C (No freezing)
Maximum operating pressure
Ambient and fluid temperature
Socket case, Plug case, Clamp ring ADC12 black anodized
SPCC, Chromated
SPCC, Zinc chromated
C3604BD
NBR
SPC Zinc chromated
Plate
Holder
Socket, Plug, Stopper
U packing
CR
Cover
SWRM Zinc chromated
Cross-recessed head machine screw, Clamp bolt
Spacer
Easy insertion of tube by the
floating mechanism to adjust
to the case hole.
Hold securely by inserting
both the tube and barb.
Possible to connect in the
required position by the
convex and concave for
engagement.
Possible to insert smoothly
by expansion of tube with
expander.
Connect within one turn
from the socket side to the
plug side.
Possible to clamp with one
bolt at once.
15-2-100

Caution
How to Use
Removing
Loosen clamp ring (1), and separate the
multiconnector into two parts,
multiconnector into two parts, socket side
and plug side.
Clamping of tube
1. After inserting tube, tighten clamp bolt
(6) clockwise with a screwdriver.
2. Barb cassette creeps into the direction
D and the tube will be clamped at the B
clamp portion (5) consisting of barb (3)
and case.
(1) Clamping ring
Insertion and removal of tube
(3) Case
(2) Stopper
(5) Barb
(6) Clamp bolt
(4) Barb cassette
A
B
C+ Driver
1. Tu rn the clamp bolt (6) to the left with a
screwdriver, loosen until the stopper (2)
touches the case (3), and barb cassette
(4) will be pulled out in the direction A.
Then clamp portion B, consisting of
barb (5) and case (3), will be freed.
Next, insert or remove the tube.
2. The corresponding numbers are
stamped on both the socket and plug
sides for each tube connection.
3. If it is hard to insert the tube, enlarge the
tube end with the head of stopper (2),
expander C, before inserting tube.
4. Insert tube until it clears mounting of
barb (5) completely.
(3) Case
B
D
+ Driver
Connection
1. Push together and rotate both of the
cases, and the plug side will slide into
the socket side at the proper position.
2. The ring E, male and female, of the plug
side and socket side will interlock with
each other at the proper position by
pushing together and rotating.
3. Final process of connection is to screw-
in the clamp ring.
Cover mounting
1. Cover is mountable on both sides, plug
side and socket side.
2. Enlarge cover and mount cover onto
mounting area.
Cover mounting area
Cover
N04DM 6
4 mm
6 mm
04
06
Tubing O.D.
6
12
6
12
Number of
connecting tubes
Multi-connector
Plug side
Socket side
Nil
P
S
Style
Tube material
Nylon
Soft nylon
Polyurethane
N
NU
Accessory (Option)
1 cover (Single side)
2 covers (Both sides)
C1
C2
How to Order
15-2-101
Multi-connector Series DM
K
M
H
D
MS
T
VMG

Dimensions: DM6/12
DM6
DM12
Model Barb I.D. (d)
1.6
3
1.6
3
AB
531
631
DM6-04N
DM6-06N
DM6-04NU
DM6-06NU
DM12-04N
DM12-06N
DM12-04NU
DM12-06NU
Panel mounting hole
(with the cover at socket side)
Panel mounting hole
Panel mounting hole
(with the cover at socket side)
Panel mounting hole
4-ø4.5
M4 round head screw
4-ø4.3
M4 round head screw
Series DM
15-2-102

Caution
1. Be sure to insert the tube slowly so that you will feel it move smoothly and can feel it
touch the end. Once the tube has been properly inserted, pull it back gently, to make
sure that it has a positive seal. If not inserted properly, it may cause air to leak or tube to
release.
2. When the number of tubes to be used is less than 6 (DM6) or 12 (DM12), the positioning
of the tube should be symmetrical to the center.
Precautions
Be sure to read before handling.
Refer to pages 15-18-3 to 15-18-4 in the front matter for Safety
Instructions and Common Precautions mentioned in this catalog, and
refer to pages 15-1-10 to 15-1-11 for Precautions on every series.
Installing of Tube
15-2-103
Multi-connector Series DM
K
M
H
D
MS
T
VMG

Multi-connector with One-touch Fittings
Series DMK
No. of Connecting Tubes: 6, 12
Plug case
Plug
Socket case
U ring
Clamp ring
Plate
Cover
Holder
Spacer
Socket
Connects the plug case with the socket.
Tight seal
Multi-connector with One-touch
fittings provide quick and easy
installation and removal of
multiple tubing (nylon, soft
nylon, and polyurethane) when
connecting to a panel of a
device.
A unique positioning
mechanism allows accurate
installation and removal of
tubing with ease even in a hard-
to-see locations, while
preventing piping errors when
reconnecting.
Built-in One-touch fittings
Applicable to nylon, soft nylon, and
polyurethane tubes.
Saves installation time
Unlike the use of multiple bulkhead unions for
panel, Series DMK with built-in One-touch
fittings significantly reduces the piping time.
Secure tube connection
Tubes are easily and securely connected to
the multi-connector with built-in One-touch
fittings.
No. of connecting tubes:
2 types of multi-connectors are available: 6
tubes and 12 tubes.
DMK12DMK6
SPCC, Zinc chromated A5052, Hard anodized
ADC12, White half-polished finish
SPCC, Chromated
C3604BD Electroless nickel plated,
POM, Stainless steel 304
NBR
Silicon rubber
SWRM, Nickel plated
SWRM, Zinc chromated
SPC, Zinc chromated
Socket case
Plug case
Clamp ring
Plate
Holder
Socket
Plug
U ring
Cover
Round head phillips screw
Round head phillips screw
with flat washer
Spacer
Principal Parts Material
Nylon, Soft nylon, Polyurethane
3.2, 4
Air
1.0 MPa
Ҁ5 to 60폶C (With no condensation)
Applicable tubing materials
Applicable tubing O.D. (mm)
Fluid
Maximum operating pressure
Ambient and fluid temperature
Specifications
Model
Plug side only
DMK6P-23
DMK6P-04
DMK12P-23
DMK12P-04
Cover part no.
(Option )
DMK-C-6
DMK-C-12
Multi-connector
DMK6-23
DMK6-04
DMK12-23
DMK12-04
Socket side only
DMK6S-23
DMK6S-04
DMK12S-23
DMK12S-04
Model
6
12
No. of
connecting
tubes
Irregular shape
permits engagement
in a proper position.
15-2-104

How to Order
Dimensions
Caution
How to Use
6
12
6
12
23
04
3.2 mm
4 mm
Tubing O.D.
Nil
P
S
Multi-connector
Plug side only
Socket side only
Style
DMK 6
Nil
C1
C2
None
Cover single side 1 pc.
Cover both sides 2 pcs.
Accessory (Option)
04
DMK6
DMK12
Panel mounting hole
6
3
25
1
4
SMC
(Socket side with cover)
Panel mounting hole
Panel mounting hole
(Socket side with cover)
Panel mounting hole
4-ø4.3
M4 round head screw
1
23
4
5
6
7
8
9
10
12
11
SMC
4-ø4.5
M4 round head screw
36
45
ø37
36
ø36
38
36
ø44
40.5
ø26 ø19
59.5
11
ø46
43
 55
43 43
11
38
50.5 69.5
ø25 ø34
) Clamp ring
Cover Cover installation latch
Precautions
*
*
Be sure to read before handling.
Please consult with SMC when the
required specification is out of
range.
Disassembly
(1) Loosen clamp ring ) and disassemble
the connector into the plug case and
socket case.
Connection
(1) Turn the cases while pressing them
against each other until the plug case
slides into the socket case at a proper
position.
(2) Align at mark
* of the plug and socket
cases and turn them against each other
to connect the two cases.
(3) Screw in the clamp ring to complete the
connection.
Installation of cover
(1) The cover can be installed on both the
plug case or socket case.
(2) Stretch the cover to install on the cover
installation latch.
Number of
connecting tubes
15-2-105
Multi-connector with One-touch Fittings Series DMK
K
M
H
D
MS
T
VMG

Safety Instructions
These safety instructions are intended to prevent a hazardous situation and/or
equipment damage. These instructions indicate the level of potential hazard by labels of
"Caution", "Warning" or "Danger". To ensure safety, be sure to observe ISO 4414 Note 1),
JIS B 8370
Note 2) and other safety practices.
1. The compatibility of pneumatic equipment is the responsibility of the person
who designs the pneumatic system or decides its specifications.
Since the products specified here are used in various operating conditions, their compatibility for the
specific pneumatic system must be based on specifications or after analysis and/or tests to meet your
specific requirements. The expected performance and safety assurance will be the responsibility of the
person who has determined the compatibility of the system. This person should continuously review
the suitability of all items specified, referring to the latest catalog information with a view to giving due
consideration to any possibility of equipment failure when configuring a system.
2. Only trained personnel should operate pneumatically operated machinery
and equipment.
Compressed air can be dangerous if an operator is unfamiliar with it. Assembly, handling or repair of
pneumatic systems should be performed by trained and experienced operators.
3. Do not service machinery/equipment or attempt to remove components until
safety is confirmed.
1. Inspection and maintenance of machinery/equipment should only be performed once measures to
prevent falling or runaway of the driver objects have been confirmed.
2. When equipment is to be removed, confirm the safety process as mentioned above. Cut the supply
pressure for this equipment and exhaust all residual compressed air in the system.
3. Before machinery/equipment is restarted, take measures to prevent shooting-out of cylinder piston
rod, etc.
4. Contact SMC if the product is to be used in any of the following conditions:
1. Conditions and environments beyond the given specifications, or if product is used outdoors.
2. Installation on equipment in conjunction with atomic energy, railway, air navigation, vehicles,
medical equipment, food and beverages, recreation equipment, emergency stop circuits, clutch and
brake circuits in press applications, or safety equipment.
3. An application which has the possibility of having negative effects on people, property, or animals,
requiring special safety analysis.
Note 1) ISO 4414: Pneumatic fluid power--General rules relating to systems.
Note 2) JIS B 8370: General Rules for Pneumatic Equipment
Warning
Caution : Operator error could result in injury or equipment damage.
Warning : Operator error could result in serious injury or loss of life.
Danger : In extreme conditions, there is a possible result of serious injury or loss of life.
15-18-3

1. Confirm the specifications.
Products represented in this catalog are designed for use in
compressed air appllications only (including vacuum), unless
otherwise indicated.
Do not use the product outside their design parameters.
Please contact SMC when using the products in applications
other than compressed air (including vacuum).
4. Use clean air
If the compressed air supply is contaminated with chemicals,
cynthetic materials, corrosive gas, etc., it may lead to break
down or malfunction.
Selection
Mounting
Piping
Air Supply
Maintenance
Operating Environment
Warning
1. Instruction manual
Install the products and operate them only after reading the
instruction manual carefully and understanding its contents.
Also keep the manual where it can be referred to as
necessary.
2. Securing the space for maintenance
When installing the products, please allow access for
maintenance.
3. Tightening torque
When installing the products, please follow the listed torque
specifications.
Warning
1. Do not use in environments where the product
is directly exposed to corrosive gases,
chemicals, salt water, water or steam.
2. Do not expose the product to direct sunlight
for an extended period of time.
3. Do not use in a place subject to heavy
vibrations and/or shocks.
4. Do not mount the product in locations where it
is exposed to radiant heat.
Warning
1. Maintenance procedures are outlined in the
operation manual.
Not following proper procedures could cause the product to
malfunction and could lead to damage to the equipment or
machine.
2. Maintenance work
If handled improperly, compressed air can be dangerous.
Assembly, handling and repair of pneumatic systems should
be performed by qualified personnel only.
3. Drain flushing
Remove drainage from air filters regularly. (Refer to the
specifications.)
4. Shut-down before maintenance
Before attempting any kind of maintenance make sure the
supply pressure is shut of and all residual air pressure is
released from the system to be worked on.
5. Start-up after maintenance and inspection
Apply operating pressure and power to the equipment and
check for proper operation and possible air leaks. If operation
is abnormal, please verify product set-up parameters.
6. Do not make any modifications to be product.
Do not take the product apart.
Warning
1. Before piping
Make sure that all debris, cutting oil, dust, etc, are removed
from the piping.
2. Wrapping of pipe tape
When screwing piping or fittings into ports, ensure that chips
from the pipe threads or sealing material do not get inside the
piping. Also, when the pipe tape is used, leave 1.5 to 2 thread
ridges exposed at the end of the threads.
Caution
1. Operating fluid
Please consult with SMC when using the product in
applications other than compressed air (including vacuum).
Regarding products for general fluid, please ask SMC about
applicable fluids.
2. Install an air dryer, aftercooler, etc.
Excessive condensate in a compressed air system may cause
valves and other pneumatic equipment to malfunction.
Installation of an air dryer, after cooler etc. is recommended.
3. Drain flushing
If condensate in the drain bowl is not emptied on a regular
basis, the bowl will over flow and allow the condensate to
enter the compressed air lines.
If the drain bowl is difficult to check and remove, it is
recommended that a drain bowl with the auto-drain option be
installed.
For compressed air quality, refer to “Air Preparation
Equipment” catalog.
Warning
Common Precautions
Be sure to read before handling.
For detailed precautions on every series, refer to main text.
15-18-4

Quality Assurance Information
(ISO 9001, ISO 14001)
Reliable quality of products in the global market
To enable our customers throughout
the world to use our products with
even greater confidence, SMC has
obtained certification for international
standards “ISO 9001” and “ISO
14001”, and created a complete
structure for quality assurance and
environmental controls. SMC
products pursue to meet its
customers’ expectations while also
considering company’s contribution in
society.
This is an international standard for quality control
and quality assurance. SMC has obtained a large
number of certifications in Japan and overseas,
providing assurance to our customers throughout
the world.
Quality management system
ISO 9001
This is an international standard related to
environmental management systems and
environmental inspections. While promoting
environmentally friendly automation technology,
SMC is also making diligent efforts to preserve
the environment.
Environmental management system
ISO 14001
Sales coordination
Production
Make customers our
first priority, offering
them reliable and
friendly service.
Market research
Product planning
After service
Process control
Inspection, testing, etc.
Initial production control
Quality system
education
Training of
suppliers
New product evaluation
Reliability design
Reliability testing
New technical
development
Education
Training
Research
Design
Development
Produce the highest
quality with the
participation of all
employees.
Create new
products using the
latest technology,
and offer the finest
products in a
timely manner.
SMC’s quality control system
Quality policies
Quality control activities
15-18-5

CE Mark
SMC Product Conforming to Inter
SMC products complying with EN/ISO, CSA/UL standards are supporting
The CE mark indicates that machines and components meet essential requirements of all the EC Directives
applied.
It has been obligatory to apply CE marks indicating conformity with EC Directives when machines and
components are exported to the member Nations of the EU.
Once “A manufacturer himself” declares a product to be safe by means of CE marking (declaration of
conformity by manufacturer), free distribution inside the member Nations of the EU is permissible.
CE Mark
SMC provides CE marking to products to which EMC and Low Voltage Directives have been applied, in
accordance with CETOP (European hydraulics and pneumatics committee) guide lines.
As of February 1998, the following 18 countries will be obliged to conform to CE mark legislation
Iceland, Ireland, United Kingdom, Italy, Austria, Netherlands, Greece, Liechtenstein, Sweden, Spain, Denmark,
Germany, Norway, Finland, France, Belgium, Portugal, Luxembourg
EC Directives and Pneumatic Components
• Machinery Directive
The Machinery Directive contains essential health and safety requirements for machinery, as applied to
industrial machines e.g. machine tools, injection molding machines and automatic machines. Pneumatic
equipment is not specified in Machinery Directive. However, the use of SMC products that are certified as
conforming to EN Standards, allows customers to simplify preparation work of the Technical Construction File
required for a Declaration of Conformity.
•Electromagnetic Compatibility (EMC) Directive
The EMC Directive specifies electromagnetic compatibility. Equipment which may generate electromagnetic
interference or whose function may be compromised by electromagnetic interference is required to be immune
to electromagnetic affects (EMS/immunity) without emitting excessive electromagnetic affects (EMI/emission).
• Low Voltage Directive
This directive is applied to products, which operate above 50 VAC to 1000 VAC and 75 VDC to 1500 VDC
operating voltage, and require electrical safety measures to be introduced.
• Simple Pressure Vessels Directive
This directive is applied to welded vessels whose maximum operating pressure (PS) and volume of vessel (V)
exceed 50 bar/L. Such vessels require EC type examination and then CE marking.
15-18-6

http://www.smcworld.com
you to comply with EC directives and CSA/UL standards.
CSA Standards & UL Standards
UL and CSA standards have been applied in North America (U.S.A. and Canada) symbolizing safety of electric
products, and are defined to mainly prevent danger from electric shock or fire, resulting from trouble with
electric products. Both UL and CSA standards are acknowledged in North America as the first class certifying
body. They have a long experience and ability for issuing product safety certificate. Products approved by CSA
or UL standards are accepted in most states and governments beyond question.
Since CSA is a test certifying body as the National Recognized Testing Laboratory (NRTL) within the
jurisdiction of Occupational Safety and Health Administration (OSHA), SMC was tested for compliance with
CSA Standards and UL Standards at the same time and was approved for compliance with the two Standards.
The above CSA NRTL/C logo is described on a product label in order to indicate that the product is approved
by CSA and UL Standards.
TSSA (MCCR) Registration Products
TSSA is the regulation in Ontario State, Canada. The products that the operating pressure is more than 5 psi
(0.03 MPa) and the piping size is bigger than 1 inch. fall into the scope of TSSA regulation.
Products conforming to CE Standard
With CE symbol for simple visual recognition
In this catalog each accredited product series is indicated with a
CE mark symbol. However, in some cases, every available
models may not meet CE compliance. Please visit our web site
for the latest selection of available models with CE mark.
Mark of compliance
for CSA
Mark of compliance
for CSA/UL
national Standards
15-18-7
SMC Product Conforming to International Standards

America Europe
U.S.A. SMC Corporation of America
3011 North Franklin Road Indianapolis, IN 46226, U.S.A.
TEL: [phone] FAX: [phone]
CANADA SMC Pneumatics (Canada) Ltd.
6768 Financial Drive Mississauga, Ontario, L5N 7J6 Canada
TEL: [phone] FAX: [phone]
MEXICO SMC Corporation (Mexico), S.A. DE C.V.
Carr. Silao-Trejo K.M. 2.5 S/N, Predio San Jose del Duranzo
C.P. 36100, Silao, Gto., Mexico
TEL: [phone] FAX: [phone]
CHILE SMC Pneumatics (Chile) S.A.
Av. La Montaña 1,115 km. 16,5 P. Norte Parque
Industrial Valle Grande, Lampa Santiago, Chile
TEL: [phone] FAX: [phone]
ARGENTINA SMC Argentina S.A.
Teodoro Garcia 3860 (1427) Buenos Aires, Argentina
TEL: [phone] FAX: [phone]
BOLIVIA SMC Pneumatics Bolivia S.R.L.
Avenida Beni Numero 4665
Santa Cruz de la Sierra-Casilla de Correo 2281, Bolivia
TEL: [phone] FAX: [phone]
VENEZUELA SMC Neumatica Venezuela S.A.
Apartado 40152, Avenida Nueva Granada, Edificio Wanlac,
Local 5, Caracas 1040-A, Venezuela
TEL: [phone] FAX: [phone]
PERU (Distributor) IMPECO Automatizacion Industrial S.A.
AV. Canevaro 752, Lince, Lima, Peru
TEL: [phone] FAX: [phone]
URUGUAY (Distributor) BAKO S.A.
Galicia 1650 esq. Gaboto C.P. 11200, Montevideo, Uruguay
TEL: [phone] FAX: [phone]
BRAZIL SMC Pneumaticos Do Brasil Ltda.
Rua. Dra. Maria Fidelis, nr. 130, Jardim Piraporinha-Diadema-S.P.
CEP: 09950-350, Brasil
TEL: [phone] FAX: [phone]
COLOMBIA (Distributor) Airmatic Ltda.
Calle 18 69-05 Apart. Aereo 081045 Santa Fe de Bogotá, Colombia
TEL: [phone] FAX: [phone]
U.K. SMC Pneumatics (U.K.) Ltd.
Vincent Avenue, Crownhill, Milton Keynes, MK8 0AN, Backinghamshire, U.K.
TEL: [phone] FAX: [phone]
GERMANY SMC Pneumatik GmbH
Boschring 13-15 D-63329 Egelsbach, Germany
TEL: [phone] FAX: [phone]
ITALY SMC Italia S.p.A.
Via Garibaldi 62 I-20061 Carugate Milano, Italy
TEL: [phone] FAX: [phone]
FRANCE SMC Pneumatique S.A.
1 Boulevard de Strasbourg, Parc Gustave Eiffel, Bussy Saint Georges, F-77600
Marne La Vallee Cedex 3 France
TEL: [phone] FAX: [phone]
SWEDEN SMC Pneumatics Sweden AB
Ekhagsvägen 29-31, S-141 05 Huddinge, Sweden
TEL: [phone] FAX: [phone]
SWITZERLAND SMC Pneumatik AG
Dorfstrasse 7, Postfach 117, CH-8484 Weisslingen, Switzerland
TEL: [phone] FAX: [phone]
AUSTRIA SMC Pneumatik GmbH (Austria)
Girakstrasse 8, A-2100 Korneuburg, Austria
TEL: [phone] FAX: [phone]
SPAIN SMC España, S.A.
Zuazobidea 14 Pol. Ind. Júndiz 01015 Vitoria, Spain
TEL: [phone] FAX: [phone]
IRELAND SMC Pneumatics (Ireland) Ltd.
2002 Citywest Business Campus, Naas Road, Saggart, Co. Dublin, Ireland
TEL: [phone] FAX: [phone]
NETHERLANDS (Associated company) SMC Pneumatics BV
De Ruyterkade 120, NL-1011 AB Amsterdam, Netherlands
TEL: [phone] FAX: [phone]
GREECE (Distributor) S.Parianopoulos S.A.
7, Konstantinoupoleos Street 11855 Athens, Greece
TEL: [phone] FAX: [phone]
DENMARK SMC Pneumatik A/S
Knudsminde 4 B DK-8300
Odder, Denmark
TEL: [phone] FAX: [phone]
SMC’s Global Service Network
15-18-20

Europe
FINLAND SMC Pneumatics Finland OY
PL72, Tiistinniityntie 4, SF-02231 ESP00, Finland
TEL: [phone] FAX: [phone]
NORWAY SMC Pneumatics Norway A/S
Vollsveien 13C, Granfoss Næringspark N-1366 LYSAKER, Norway
TEL: [phone] FAX: [phone]
BELGIUM (Distributor) SMC Pneumatics N.V./S.A.
Nijverheidsstraat 20 B-2160 Wommelgem Belguim
TEL: [phone] FAX: [phone]
POLAND SMC Industrial Automation Polska Sp.z.o.o.
ul. Konstruktorska 11A, PL-02-673 Warszawa, Poland
TEL: [phone] FAX: [phone]
TURKEY (Distributor) Entek Pnömatik San.ve Tic. Ltd. Sti
Perpa Tic. Merkezi Kat:11 No.1625 80270 Okmeydani Istanbul, Türkiye
TEL: [phone] FAX: [phone]
RUSSIA SMC Pneumatik LLC.
36/40 Sredny prospect V.O. St. Petersburg 199004, Russia
TEL: [phone] FAX: [phone]
CZECH SMC Industrial Automation CZ s.r.o.
Hudcova 78a, CZ-61200 Brno, Czech Republic
TEL: [phone] FAX: [phone]
HUNGARY SMC Hungary Ipari Automatizálási kft.
Budafoki ut 107-113 1117 Budapest
TEL: [phone] FAX: [phone]
ROMANIA SMC Romania S.r.l.
Str. Frunzei, Nr. 29, Sector 2, Bucharest, Romania
TEL: [phone] FAX: [phone]
SLOVAKIA SMC Priemyselná automatizáciá, s.r.o
Nova 3, SK-83103 Bratislava
TEL: [phone] FAX: [phone]
SLOVENIA SMC Industrijska Avtomatilca d.o.o.
Grajski trg 15, SLO- 8360 Zuzemberk, Slovenia
TEL: [phone] FAX: [phone]
SOUTH AFRICA (Distributor) Hyflo Southern Africa (Pty.) Ltd.
P.O.Box 240 Paardeneiland 7420 South Africa
TEL: [phone] FAX: [phone]
EGYPT (Distributor) Saadani Trading & Ind. Services
15 Sebaai Street, Miami 21411 Alexandria, Egypt
TEL: [phone] FAX: [phone]
Oceania/Asia
AUSTRALIA SMC Pneumatics (Australia) Pty.Ltd.
14-18 Hudson Avenue Castle Hill NSW 2154, Australia
TEL: [phone] FAX: [phone]
NEW ZEALAND SMC Pneumatics (New Zealand) Ltd.
8C Sylvia Park Road Mt.Wellington Auckland, New Zealand
TEL: [phone] FAX: [phone]
TAIWAN SMC Pneumatics (Taiwan) Co.,Ltd.
17, Lane 205, Nansan Rd., Sec.2, Luzhu-Hsiang, Taoyuan-Hsien, TAIWAN
TEL: [phone] FAX: [phone]
HONG KONG SMC Pneumatics (Hong Kong) Ltd.
29/F, Clifford Centre, 778-784 Cheung, Sha Wan Road, Lai Chi Kok, Kowloon,
Hong Kong
TEL: [phone] FAX: [phone]
SINGAPORE SMC Pneumatics (S.E.A.) Pte. Ltd.
89 Tuas Avenue 1, Jurong Singapore 639520
TEL: [phone] FAX: [phone]
PHILIPPINES SHOKETSU SMC Corporation
Unit 201 Common Goal Tower, Madrigal Business Park,
Ayala Alabang Muntinlupa, Philippines
TEL: [phone] FAX: [phone]
MALAYSIA SMC Pneumatics (S.E.A.) Sdn. Bhd.
Lot 36 Jalan Delima1/1, Subang Hi-Tech Industrial Park, Batu 3 40000 Shah Alam
Selangor, Malaysia
TEL: [phone] FAX: [phone]
SOUTH KOREA SMC Pneumatics Korea Co., Ltd.
Woolim e-BIZ Center (Room 1008), 170-5, Guro-Dong, Guro-Gu,
Seoul, 152-050, South Korea
TEL: [phone] FAX: [phone]
CHINA SMC (China) Co., Ltd.
7 Wan Yuan St. Beijing Economic & Technological Development Zone 100176, China
TEL: [phone] FAX: [phone]
THAILAND SMC Thailand Ltd.
134/6 Moo 5, Tiwanon Road, Bangkadi, Amphur Muang, Patumthani 12000, Thailand
TEL: [phone] FAX: [phone]
INDIA SMC Pneumatics (India) Pvt. Ltd.
D-107 to 112, Phase-2, Extension, Noida, Dist. Gautaim Budh Nagar,
U.P. 201 305, India
TEL: [phone] FAX: [phone]
INDONESIA (Distributor) P.T. Riyadi Putera Makmur
Jalan Hayam Wuruk Komplek Glodok Jaya No. 27-28 Jakarta 11180 Indonesia
TEL: [phone] FAX: [phone]
PAKISTAN (Distributor) Jubilee Corporation
First Floor Mercantile Centre, Newton Road Near Boulton Market P.O. Box 6165
Karachi 74000 Pakistan
TEL: [phone] FAX: [phone]
ISRAEL (Distributor) Baccara Automation Control
Kvutzat Geva 18915 Israel
TEL: [phone] FAX: [phone]
SAUDI ARABIA (Distributor) Assaggaff Trading Est.
P.O. Box 3385 Al-Amir Majed Street, Jeddah-21471, Saudi Arabia
TEL: [phone] FAX: [phone]
15-18-21
SMC’s Global Service Network