SMC Networks 7004VBR User manual

Copyright
Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable. However, no
responsibility is assumed by SMC for its use, or for any infringements of patents or other rights of third
parties which may result from its use. No license is granted by implication or otherwise under any patent or
patent rights of SMC. SMC reserves the right to change specifications at any time without notice.
The products and programs described in this User Guide are licensed products of SMC. This User Guide
contains proprietary information protected by copyright, and this User Guide and all accompanying
hardware and documentation are copyrighted.
SMC does not warrant that the hardware will work properly in all environments and applications, and
makes no warranty and representation, either implied or expressed, with respect to the quality,
performance, merchantability, or fitness for a particular purpose.
Information in this User Guide is subject to change without notice and does not represent a commitment on
the part of SMC. SMC assumes no responsibility for any inaccuracies that may be contained in this User
Guide.
SMC makes no commitment to update or keep current the information in this User Guide, and reserves the
right to make changes to this User Guide and/or product without notice.
No part of this manual may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying, recording, or information storage and retrieval systems, for any
purpose other than the purchaser's personal use, without the express written permission of SMC.
Copyright © 2004 by
SMC Networks, Inc.
38 Tesla
Irvine, California 92618
All rights reserved.
Trademarks
SMC® is a registered trademark; and EZ-Stream, EZ Connect, Barricade and EZ Hub are trademarks of
SMC Networks, Inc. Other product and company names are trademarks or registered trademarks of their
respective holders.
ii

Compliances
FCC - Class B
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with instructions, may cause harmful interference to
radio communications. However, there is no guarantee that the interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
FCC Caution: To assure continued compliance, (for example - use only shielded interface cables when
connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
CAUTION STATEMENT:
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 5 centimeters between the
radiator and your body. This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter. Note: In order to maintain compliance with the limits of a Class B digital device,
SMC requires that you use a quality interface cable when connecting to this device. Changes or
modifications not expressly approved by SMC could void the user’s authority to operate this equipment.
Attach unshielded twisted-pair cable (UTP) to the RJ-45 port and shielded USB cable to the USB port.
iii

EC Conformance Declaration – Class B
SMC contact for these products in Europe is:
SMC Networks Europe,
Edificio Conata II
Calle Fructuos Gelabert 6-8, 2o, 4a
08970 – Sant Joan Despi
Barcelona, Spain
This equipment complies with the requirements relating to electromagnetic compatibility, EN 55022/A1
Class B, and EN 50082-1. This meets the essential protection requirements of the European Council
Directive 89/336/EEC on the approximation of the laws of the member states relation to electromagnetic
compatibility.
Important Safety Notices
•Unplug this product from the AC power before cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a dry cloth for cleaning.
•Route the power supply cords so that they are not likely to be walked on or pinched by items
placed upon or against them. Pay particular attention to cords at plugs, convenience receptacles,
and the point where they exit from the product.
•Situate the product away from heat sources such as radiators, heat registers, stoves, and other
products that produce heat.
•To prevent fire or shock hazard, do not expose this unit to rain or moisture. Do not allow water or
any foreign objects to enter the interior. This may cause a fire or electric shock. In the event that
water or other foreign objects get into the product, immediately unplug the AC adapter from the
electrical outlet and contact Customer Service for inspection and/or repair/replacement options.
•Do not take apart the equipment. This may cause fire, electric shock or other injuries.
•Do not overload wall outlets and extension cords as this can result in a fire or electric shock.
•This product is for use with the AC adapter that comes with it. Use with any other AC power is
strongly discouraged as it may cause fire, electric shock, or damage to the equipment.
iv

TABLE OF CONTENTS
1 | SYSTEM REQUIREMENTS 8
2 | EQUIPMENT CHECKLIST 8
3 | FUNCTIONS AND FEATURES 9
4 | PANEL LAYOUT 10
5 | HARDWARE INSTALLATION 10
6 | NETWORK SETTINGS AND SOFTWARE INSTALLATION 11
6.1 | Installing TCP/IP 11
6.2 | Setting up TCP/IP 11
6.3 | Obtaining an IP Address 12
6.4 | Configuring a Macintosh Computer 13
6.5 | Verifying Your TCP/IP Connection 13
7 | CONFIGURING YOUR BROADBAND ROUTER 14
7.1 | Browser Configuration 14
7.2 | Web Management 14
7.3 | Setup Wizard 15
7.3.1 | Time Zone 15
7.3.2 | Broadband Type 15
7.3.4 | Cable Modem 16
7.3.5 | Fixed-IP xDSL 16
7.3.6 | PPPoE xDSL 17
7.3.7 | PPTP 18
v

7.3.8| BigPond 18
7.4 | Advanced Setup – SYSTEM 19
7.4.1| Time Zone 19
7.4.2| Password Settings 20
7.4.3| Remote Management 20
7.5 | Advanced Setup - WAN 21
7.5.1| Dynamic IP 21
7.5.2| PPPoE 21
7.5.3| PPTP 22
7.5.4| Static IP 22
7.5.6| BigPond 23
7.6 | Advanced Setup - LAN 23
7.7 | Advanced Setup - NAT 24
7.7.1 | Virtual Server 24
7.7.2 | Special Applications 25
7.8 | Advanced Setup - FIREWALL 26
7.8.1 | URL Blocking 26
7.8.2 | MAC Filter 27
7.8.3 | Parental Control 28
7.8.4 | DMZ 29
7.8.5 | Advanced Firewall Settings 29
7.9 | DDNS (Dynamic DNS) 30
7.10 | UPnP (Universal Plug-and-Play) 30
7.11 | Tools 31
7.12 | Status 31
vi

8 | TROUBLESHOOTING 32
9 | TERMINOLOGY 34
10 | TECHNICAL SPECIFICATIONS 38
11 | COMPLIANCES 39
12 | LEGAL INFORMATION AND CONTACTS 41
vii

1 | System Requirements
• Internet access from your local telephone company or Internet Service Provider (ISP) using
a DSL modem, cable modem, Dial-Up modem, or ISDN modem
• A PC using a fixed IP address or dynamic IP address assigned via DHCP, as well as a
Gateway server address and DNS server address from your service provider
• A computer equipped with a 10 Mbps, 100 Mbps, or 10/100 Mbps Fast Ethernet card, or a
USB-to-Ethernet converter
• TCP/IP network protocol installed on each PC that needs to access the internet
• A Java-enabled web browser, such as Microsoft Internet Explorer 5.0 or above, or Netscape
Communicator 4.0 or above installed on one PC at your site for configuring the router.
2 | Equipment Checklist
After unpacking the Barricade™ Cable/DSL Broadband Router, check the contents of the box to be sure
you have received the following components:
• 1 Barricade™ Cable/DSL Broadband Router
• 1 EZ Installation Wizard and Documentation CD
• 1 Ethernet (CAT5-UTP/Straight-Through) Cable
• 1 Power Adapter
• 1 Quick Installation Guide
Immediately inform your dealer in the event of any incorrect, missing or damaged parts. If possible, please
retain the carton and original packing materials in case there is a need to return the product.
Please register this product and upgrade the product warranty at SMC's Web site:
http://www.smc.com
8

3 | Functions and Features
Broadband Modem and NAT Router Connects multiple computers to a broadband (cable or DSL)
modem, and/or Ethernet router to access the Internet.
10/100 Mbps Ethernet Interface Provides a 10/100 Base-TX interface to connect to a DSL or cable
modem for broadband Internet access.
Auto-sensing Ethernet Switch Equipped with a 4-port auto-sensing Ethernet switch.
WAN type supported
The router supports some WAN types, Static, Dynamic, PPPOE,
PPTP, and Dynamic IP with Road Runner.
Firewall All unwanted packets from outside sources are blocked to protect
your intranet.
DHCP Server Supported All networked computers can retrieve TCP/IP settings
automatically from this device.
Web-based Configuration Configurable by any networked computer’s Web browser using
Netscape or Internet Explorer.
Network Filter Supported The Packet Filter lets you control access to a network by analyzing
the incoming and outgoing packets; this lets you either pass or halt
the packets based on the IP address or the source and destination.
Universal Plug and Play (UPnP)
Supported
Enables devices such as PCs, routers and printers to be plugged
into a network and ensure automatic recognition.
Virtual Server Supported Lets you make your Website, FTP site, and other services on your
LAN accessible to Internet users.
User Defined Application Sensing
Tunnel
Lets you define the attributes to support special applications that
require multiple connections like Internet gaming, video
conferencing, Internet telephony, and so on. This device can sense
the application type and opens a multi-port tunnel for it.
DMZ Host Supported Enables a computer to be fully accessible to the Internet. This
function is used when the special application sensing tunnel
feature is insufficient to allow an application to function correctly.
SNMP Supported SNMP (Simple Network Management Protocol) is a protocol that
lets users remotely manage a computer network by polling and
setting terminal values, and monitoring network events.
System Time Supported Lets you synchronize system time with the network time server.
Virtual Computers Supported The virtual computer lets you use the original NAT feature, which
lets you setup the one-to-one mapping of multiple global and local
IP addresses.
URL Blocking Supported Lets you block hundreds of Website connections by simply
entering a keyword.
Schedule Rule Lets you set a time schedule for different services.
Routing Table Supported Allows you to determine which physical interface address to use
for outgoing IP data grams. If you have more than one router and
subnet, enable the routing table to allow packets to find the proper
routing path and the different subnets to communicate with each
other.
9

4 | Panel Layout
The following figure shows the front panel layout, which is followed by a table describing in detail the
status and function of each LED.
SMC7004VBR
LED ON OFF FLASHING
PWR Receiving power Not receiving power N/A
WAN Good WAN
connection detected
No WAN
connection detected
Transmitting or
receiving traffic
LINK/ACT Good LAN
connection detected
No LAN connection
detected
Transmitting or
receiving traffic
10/100
Mbps
LAN port operating
at 100 Mbps
LAN port operating
at 10 Mbps
N/A
5 | Hardware Installation
The router can be placed anywhere in your office or home. No special wiring or cooling
requirements are necessary. However, you should comply with the following guidelines:
• Place your router on a flat, horizontal surface
• Be sure to place your router away from any heating devices
• Avoid dusty and/or humid areas
1) Setup LAN Connection: Connect an Ethernet cable from your computer’s Ethernet port to one of
the LAN ports of the router.
2) Setup WAN Connection: Insert one end of the Ethernet cable into the WAN port on the back
panel of your router, and the other end to the cable/DSL modem. You may connect an analog
modem (optional) to function as a backup connection.
3) Power Up: The router automatically enters the self-testing phase once the power cord is plugged
into a wall outlet. When in self-testing phase, the M1 indicator LED illuminates for about five
seconds to indicate proper connection. The M1 LED flashes twice as soon as the self-testing phase
is completed. After the completion of the self-testing phase, the M1 LED should flash once per
second to indicate that the router is functioning properly.
10