SMC Networks 7204BRB User manual

SMC7204BRB
4-port ADSL Router with
built-in ADSL Modem (Annex B)
Model Number: SMC7204BRB
Quick Installation Guide
Guide d’installation rapide
Guía de inicio rápido
Beknopte installatiehandleiding
Manual de instalação rápida
4-port ADSL Router with built-in ADSL Modem
Routeur ADSL 4 ports avec modem ADSL intégré
Router ADSL de 4 puertos con módem ADSL integrado
4-poorts ADSL-router met ingebouwde ADSL-modem
Router ADSL de 4 Portas com Modem ADSL Integrado

English
2
Contents
1
•One ADSL BarricadeTM.
•One Power adapter.
•One RJ-45 Ethernet cable.
•One RJ-11 Standard phone/DSL line cable.
•One Installation utility and Documentation CD.
•Quick Installation Guide.
Note: ADSL splitters/microfilters are included with some models.
Package Contents
English 2 - 21
Deutsch 22 - 41
Français 42 - 61
Español 62 - 81
Nederlands 82 - 101
Português 102 - 121
Compliances & Information 122 - 130
Contents

Front Panel
English
4
Hardware Description
English
3
System Requirements
In order to use the ADSL BarricadeTM, you must have
the following:
•ADSL service up and running on your telephone line,
with at least one public Internet address for your LAN.
•One or more computers, each containing an Ethernet
10/100 Base-T network interface card (NIC).
•An Ethernet hub/switch, if you are connecting the device
to more than one computer on an Ethernet network.
•For system configuration using the supplied web-based
program: a web browser such as Internet Explorer V5.0
or later, or Netscape V6.1 or later.
LED Label
Color Status
Green Steady
Green Blink
Yellow Steady
Yellow Blink
OFF
Power
Green
Power On
N/A
N/A
N/A
Power Off
Link
Green
ADSL line
is trained.
Training
N/A
N/A
No
Connection
TX/RX
Green
DSL Transmitting/
Receiving
TX/RX
N/A
N/A
No TX/RX
Ethernet
1 2 3 4
Green / 100 Mbps
Yellow / 10 Mbps
Link
Transmitting/
Receiving
Link
Transmitting/
Receiving
No Connection

5
English
6
English
This Quick Installation Guide provides basic instructions for
connecting the ADSL BarricadeTM to a computer or LAN and to the
Internet.
•Section 1 describes how to set up the hardware.
•Section 2 describes how to configure Internet properties on
your computer(s).
•Section 3 shows you how to configure ISP settings using
Auto Setup utility.
This Guide assumes that you have already established an ADSL
service with your Internet service provider (ISP). These
instructions provide a basic configuration that should be
compatible with your home or small office network setup.
5
Rear Panel
Description
12V, 1.2A
If depressed for 1-2 seconds: reset.
If depressed for 5 seconds or more:
reset to factory default.
RJ-11 phone connector
Four 10/100M RJ-45 connectors
Rear Panel
Connector
Power Supply
Reset and Restore
Factory Defaults
Button
DSL Port
Ethernet Port

English
8
English
7
Connecting the Hardware
1
Warning: Before you begin, turn the power off for all devices.
These include your computer(s), your LAN hub/switch
(if applicable), and the ADSL BarricadeTM.
Step 1. Connect the ADSL cable
Connect one end of the provided phone cable (RJ-11) to the port
labeled DSL on the Rear Panel of the device. Connect the other
end to your ADSL Microfilter/Splitter*.
*Note: ADSL splitters/microfilters are included with some models.
Step 2. Connect the Ethernet cable
If you are connecting a LAN to the ADSL BarricadeTM, attach one
end of a provided Ethernet cable to hub/switch port and the other
to the Ethernet port on the ADSL BarricadeTM. If you are using the
ADSL BarricadeTM with a single computer and no hub, you must use
an Ethernet cable to attach the PC directly to the device.
Step 3. Attach the power connector
Connect the AC power adapter to the Power connector on the back
of the device and plug in the adapter to a wall outlet or power
strip.
Step 4. Power up your systems
Turn on and boot up your computer(s) and any LAN device such
as hubs or switches.

English
910
English
3. In the [LAN or High-Speed Internet] window, right-click on
the icon corresponding to your network interface card (NIC)
and select [Properties]. (Often, this icon is labeled [Local
Area Connection].) The [Local Area Connection] dialog box
displays a list of currently installed network items.
4. Ensure that the check box to the left of the item labeled
[Internet Protocol TCP/IP] is checked, and click [Properties].
5. In the [Internet Protocol (TCP/IP) Properties] dialog box,
click the radio button labeled [Obtain an IP address
automatically]. Also click the radio button labeled [Obtain
DNS server address automatically].
6. Click [OK] twice to confirm your changes, and close
the [Control Panel].
This section provides instructions for configuring the Internet
settings on your computers to work with the ADSL BarricadeTM.
Before you begin
By default, the ADSL BarricadeTM automatically assigns all required
Internet settings to your PCs. You need only to configure the PCs
to accept the information when it is assigned. Follow the
instructions that correspond to the operating system installed
on your PC.
Windows® XP
1. In the Windows task bar, click the [Start] button,
and then click [Control Panel].
2. Double-click the [Network Connections] icon.
Configuring
Your Computers
2

English
12
English
11
Windows 2000
First, check for the IP protocol and, if necessary, install it.
1. In the Windows task bar, click the [Start] button,
point to [Settings], and then click [Control Panel].
2. Double-click the [Network and Dial-up Connections] icon.
3. In the [Network and Dial-up Connections] window, right-click
the [Local Area Connection] icon, and then select
[Properties]. The [Local Area Connection Properties] dialog
box displays a list of currently installed network components.
If the list includes [Internet Protocol (TCP/IP)], then the
protocol has already been enabled. Skip to Step 10.
4. If [Internet Protocol (TCP/IP)] does not appear as
an installed component, click [Install…].
5. In the [Select Network Component Type] dialog box,
select [Protocol], and then click [Add…].
6. Select [Internet Protocol (TCP/IP)] in the [Network Protocols]
list, and then click [OK]. You may be prompted to install files
from your Windows 2000 installation CD or other media.
Follow the instructions to install the files.
7. If prompted, click [OK] to restart your computer with the new
settings. Next, configure the PCs to accept IP information
assigned by the ADSL BarricadeTM.
8. In the [Control Panel], double-click the [Network and Dial-up
Connections] icon.

English
13
English
14
9. In the [Network and Dial-up Connections] window, right-click
the [Local Area Connection] icon, and then select
[Properties].
10. In the [Local Area Connection Properties] dialog box, select
[Internet Protocol (TCP/IP)], and then click [Properties].
11. In the [Internet Protocol (TCP/IP) Properties] dialog box,
click the radio button labeled [Obtain an IP address
automatically]. Also click the radio button labeled [Obtain
DNS server address automatically].
12. Click [OK] twice to confirm and save your changes, and then
close the [Control Panel].
Windows 98/Me/SE
1. In the Windows task bar, click the [Start] button,
point to [Settings], and then click [Control Panel].
2. Double-click the [Network and Dial-up Connections] icon.
3. In the [Network and Dial-up Connections] window, right-click
the [Network] icon, and then select [Properties]. The [Network
Properties] dialog box displays a list of currently installed
network components. If the list includes [Internet Protocol
(TCP/IP)], then the protocol has already been enabled. Skip to
Step 11.

English
16
English
16
15
9. In the [Control Panel], double-click the [Network and Dial-up
Connections] icon.
10. In the [Network and Dial-up Connections] window, right-click
the [Network] icon, and then select [Properties].
11. In the [Network Properties] dialog box, select [TCP/IP],
and then click [Properties].
12. In the [TCP/IP Settings] dialog box, click the radio button
labeled [Server assigned IP address]. Also click the radio
button labeled [Server assigned name server address].
13. Click [OK] twice to confirm and save your changes,
and then close the Control Panel.
Note: For Windows 95 and NT, please see the installation
instructions in the User Guide contained on the CD Rom.
4. If [Internet Protocol (TCP/IP)] does not appear as
an installed component, click [Add…].
5. In the [Select Network Component Type] dialog box,
select [Protocol], and then click [Add…].
6. Select [Microsoft] in the [Manufacturers] box.
7. Select [Internet Protocol (TCP/IP)] in the [Network Protocols]
list, and then click [OK]. You may be prompted to install files
from your Windows Me installation CD or other media. Follow
the instructions to install the files.
8. If prompted, click [OK] to restart your computer with the new
settings. Next, configure the PCs to accept IP information
assigned by the ADSL BarricadeTM.

English
18
English
17
This section provides instructions on how to use the Auto Setup
utility for configuration of the ADSL BarricadeTM for your ISP.
1. Insert the Installation utility and Documentation CD into
your CD drive.
2. Browse to the location of your CD drive and run AutoSetup.exe.
This will start the Auto Setup utility, which provides an easy
way to configure the ADSL BarricadeTM for your ISP.
3. Click [Yes, I agree] to accept terms of license agreement
and continue with the setup.
Configuring
the ADSL BarricadeTM
3
4. Select your country from the drop down list, then click [Next]
to continue. If your country is not listed, click [Custom] and
skip to section Custom.
5. Select your ISP/Network provider from the drop down list, then
click [Next] to continue. If your ISP/Network Provider is not
listed, click [Custom] and skip to section Custom.
6. Enter the Username and password supplied by your ISP, then
click [Next] to continue.
Note: You will only be required to enter a username and password if
your ISP uses protocol PPPoA or PPPoE. If your ISP uses
RFC1483 Bridging no further input is required, simply click
[Next] to continue.
If your ISP uses RFC1483 Routed after clicking [Next] you
will be required to enter the IP address, Netmask, Gateway
address, Primary and Secondary DNS address supplied by
your ISP. Click [Next].