SMC Networks SMCWTVG User manual

Steps to configure
SMCWTVG Analog Telephone Adaptor
Configuration Guide

Steps to self-configure
SMC ATA
1
Sign up for Owtalk at http://www.owtalk.com to get your self-
configuration information for SMC ATA.
Plug the power cord and connect the WAN port on the back of the ATA
to your cable/ADSL modem, router, or broadband Internet connection.
The factory default network setting of most of the ATA is set as DHCP
mode, i.e. the device obtains the IP address automatically from the net-
work. Follow the steps below if your ATA is in DHCP mode. Otherwise
please refer to the device user manual on how to configure your device
to connect to a LAN or Internet under Static IP or PPPoE mode.
Connect your traditional landline phone to the ATA.
2
3
4
Overview
This guide shows how to configure SMCWTVG Analog Telephone Adaptor
(ATA) so you can use the Owtalk service. But first you must be an Owtalk
subscriber.
SMC ATA can be available in preconfigured mode, labeled as Owtalk
Preconfigured on the surface of the packaging box. Under the preconfigured
mode, all Owtalk SIP account information are pre-programmed, you don’t
need to go through the following procedures. Please refer to Appendix A on
how to activate an Owtalk preconfigured device.

Steps to self-configure
SMC ATA
1
Sign up for Owtalk at http://www.owtalk.com to get your self-
configuration information for SMC ATA.
Plug the power cord and connect the WAN port on the back of the ATA
to your cable/ADSL modem, router, or broadband Internet connection.
The factory default network setting of most of the ATA is set as DHCP
mode, i.e. the device obtains the IP address automatically from the net-
work. Follow the steps below if your ATA is in DHCP mode. Otherwise
please refer to the device user manual on how to configure your device
to connect to a LAN or Internet under Static IP or PPPoE mode.
Connect your traditional landline phone to the ATA.
2
3
4
Overview
This guide shows how to configure SMCWTVG Analog Telephone Adaptor
(ATA) so you can use the Owtalk service. But first you must be an Owtalk
subscriber.
SMC ATA can be available in preconfigured mode, labeled as Owtalk
Preconfigured on the surface of the packaging box. Under the preconfigured
mode, all Owtalk SIP account information are pre-programmed, you don’t
need to go through the following procedures. Please refer to Appendix A on
how to activate an Owtalk preconfigured device.
Open Internet Explorer (or any other) web browser on your computer.
Enter the default IP address of the ATA in the address field. Please type
http://192.168.0.109 in the address field.
Enter smcamdin in the field of Password. Click Login.
Click VOIP and then SIP Settings to enter the SIP Configuration. The
configuration information is available in the self-configuration tab in
Owtalk after sign-up or click View SIP Account Configuration in
Owtalk My Account page.
Fill in the 10-digits Owtalk SIP User Name in the field of Number and User ID /
Account.
Fill in the Owtalk SIP Password in the field of Password and Confirm Password.
Fill in the Owtalk SIP Proxy/Server in the field of Proxy Server IP / Domain.
5
7
6

The SIP port number is set at 6060 . For the remaining tabs, you can
accept the default settings, or you change them to suit your setup. And
then click Save and Apply .
After the ATA set up procedure is complete, the device is ready for use
and you can now receive and make outgoing calls.
8
9

The SIP port number is set at 6060 . For the remaining tabs, you can
accept the default settings, or you change them to suit your setup. And
then click Save and Apply .
After the ATA set up procedure is complete, the device is ready for use
and you can now receive and make outgoing calls.
8
9
To activate your Owtalk preconfigured device, you need to obtain an
activation number. Go to My Account after sign-up for Owtalk at
http://www.owtalk.com . Press Port to Preconfigured and click Next to get
the activation number.
Simply dial the activation number after connecting your ATA to your
cable/ADSL modem, router, or broadband Internet connection. Your ATA is
then all set and ready for use.
Appendix A
Owtalk Preconfigured
SMC ATA