Smeg SC106T User manual

3
Table of Contents
INSTRUCTIONS FOR THE USER: these provide recommendations for
use, a description of the controls and the correct procedures for cleaning
and maintaining the appliance
INSTRUCTIONS FOR THE INSTALLER: these are intended for the
qualified engineer who is to install, commission and test the appliance
1. PRECAUTIONS FOR USE ..................................................................... 4
2. DISPOSAL INSTRUCTIONS - OUR ENVIRONMENT POLICY ............. 5
3. SAFETY PRECAUTIONS ....................................................................... 6
4. GET TO KNOW YOUR OVEN................................................................ 7
5. BEFORE INSTALLATION....................................................................... 7
6. DESCRIPTION OF FRONT PANEL CONTROLS .................................. 8
7. USING THE OVEN ............................................................................... 10
8. USING THE PIZZA FUNCTION (ON SOME MODELS ONLY) ............ 17
9. ACCESSORIES AVAILABLE................................................................ 19
10. RECOMMENDED COOKING TABLES ................................................ 20
11. CLEANING AND MAINTENANCE........................................................ 23
12. EXTRAORDINARY MAINTENANCE.................................................... 25
13. INSTALLING THE APPLIANCE............................................................ 29

4
Precautions for use
1. PRECAUTIONS FOR USE
THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE. TAKE GOOD CARE
OF IT AND KEEP IT TO HAND THROUGHOUT THE OVEN'S LIFE CYCLE.
WE URGE YOU TO READ THIS MANUAL AND ALL THE INFORMATION IT
CONTAINS CAREFULLY BEFORE USING THE APPLIANCE. INSTALLATION
MUST BE CARRIED OUT BY QUALIFIED STAFF IN COMPLIANCE WITH THE
RELEVANT REGULATIONS. THIS APPLIANCE IS INTENDED FOR HOUSEHOLD
USE AND COMPLIES WITH THE EEC DIRECTIVES CURRENTLY IN FORCE.
THE APPLIANCE IS BUILT TO PROVIDE THE FOLLOWING FUNCTION:
COOKING AND HEATING FOODS; ALL OTHER USES ARE TO BE
CONSIDERED IMPROPER.
THE MANUFACTURER DECLINES ALL LIABILITY FOR USES OTHER THAN
THOSE STATED ABOVE.
NEVER USE THIS APPLIANCE FOR HEATING ROOMS.
NEVER LEAVE PACKAGING RESIDUES UNATTENDED IN THE HOME.
SEPARATE THE VARIOUS PACKAGING MATERIALS BY TYPE AND CONSIGN
THEM TO THE NEAREST SEPARATE DISPOSAL CENTRE.
THIS APPLIANCE IS TAGGED UNDER EUROPEAN DIRECTIVE 2002/96/EC ON
WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE).
THIS DIRECTIVE CONTAINS THE REGULATIONS GOVERNING THE
COLLECTION AND RECYCLING OF DECOMMISSIONED APPLIANCES
THROUGHOUT THE EUROPEAN UNION.
NEVER OBSTRUCT THE OPENINGS AND SLITS PROVIDED FOR
VENTILATION AND HEAT DISPERSAL.
THE NAMEPLATE WITH THE TECHNICAL DATA, SERIAL NUMBER AND MARK
IS IN A VISIBLE POSITION ON THE OVEN DOOR FRAME.
THE NAMEPLATE MUST NEVER BE REMOVED.
NEVER USE METAL SCOURING PADS OR SHARP SCRAPERS;
THEY WILL DAMAGE SURFACES.
USE ORDINARY NON-ABRASIVE PRODUCTS WITH THE AID OF
WOODEN OR PLASTIC UTENSILS IF NECESSARY. RINSE
THOROUGHLY AND DRY WITH A SOFT CLOTH OR CHAMOIS
LEATHER.
DO NOT ALLOW SPILLS OF FOODS WITH HIGH SUGAR CONTENT
(E.G. JAM) TO DRY INSIDE THE OVEN. IF THEY DRY FOR TOO
LONG, THEY MIGHT DAMAGE THE ENAMEL COATING OF THE
INSIDE OF THE OVEN.

5
Disposal instructions
2. DISPOSAL INSTRUCTIONS - OUR
ENVIRONMENT POLICY
Our products are only packaged using non-pollutant, environment-friendly,
recyclable materials. We urge you to cooperate by disposing of the
packaging properly. Contact your local dealer or the competent local
organisations for the addresses of collection, recycling and disposal
facilities.
Never leave all or part of the packaging lying around. Packaging parts, and
especially plastic bags, may represent a suffocation hazard for children.
Your old appliance must also be disposed of properly.
Important: deliver the appliance to your local organisation authorised to
collect scrapped appliances. Proper disposal allows the intelligent
recovery of valuable materials.
Before scrapping your appliance it is important to remove doors and leave
shelves in position as for use, to ensure that children cannot accidentally
become trapped inside the oven during play. Also, cut the power supply
lead and remove it and the plug.

6
Safety precautions
3. SAFETY PRECAUTIONS
REFER TO THE INSTALLATION INSTRUCTIONS FOR THE SAFETY
REGULATIONS FOR ELECTRIC OR GAS APPLIANCES AND VENTILATION
FUNCTIONS.
IN YOUR INTEREST AND TO ENSURE YOUR SAFETY, BY LAW ALL ELECTRIC
APPLIANCES MUST ONLY BE INSTALLED AND SERVICED BY QUALIFIED
STAFF, IN ACCORDANCE WITH THE RELEVANT REGULATIONS.
OUR APPROVED INSTALLATION ENGINEERS GUARANTEE YOU A JOB WELL
DONE.
GAS OR ELECTRIC APPLIANCES MUST ALWAYS BE DISCONNECTED BY
SUITABLY SKILLED PEOPLE.
THE PLUG TO BE CONNECTED TO THE POWER SUPPLY LEAD AND THE
RELATIVE SOCKET MUST BE OF THE SAME TYPE AND COMPLY WITH THE
RELEVANT REGULATIONS.
THE POWER SUPPLY SOCKET MUST BE ACCESSIBLE EVEN AFTER THE
APPLIANCE HAS BEEN BUILT-IN.
NEVER DISCONNECT THE PLUG BY PULLING ON THE POWER SUPPLY
LEAD.
THE APPLIANCE MUST BE CONNECTED TO EARTH IN COMPLIANCE WITH
ELECTRICAL SYSTEM SAFETY REGULATIONS.
IMMEDIATELY AFTER INSTALLATION, CARRY OUT A QUICK TEST ON THE
APPLIANCE FOLLOWING THE INSTRUCTIONS PROVIDED LATER IN THIS
MANUAL. IF THE APPLIANCE FAILS TO OPERATE, DISCONNECT IT FROM
THE ELECTRICAL MAINS AND CONTACT YOUR NEAREST SERVICE CENTRE.
NEVER ATTEMPT TO REPAIR THE APPLIANCE.
NEVER PLACE INFLAMMABLE OBJECTS IN THE OVEN: IF IT SHOULD
ACCIDENTALLY BE SWITCHED ON, THIS MIGHT CAUSE A FIRE.
THE APPLIANCE BECOMES VERY HOT DURING USE. TAKE CARE NOT TO
TOUCH THE HEATING ELEMENTS INSIDE THE OVEN.
THE APPLIANCE IS INTENDED FOR USE BY ADULTS. KEEP CHILDREN AT A
SAFE DISTANCE AND NEVER ALLOW THEM TO PLAY WITH IT.
WHEN THE GRILL IS IN OPERATION, ACCESSIBLE PARTS MAY BECOME
VERY HOT: KEEP CHILDREN AT A SAFE DISTANCE.
AFTER EACH USE, ALWAYS CHECK THAT THE CONTROL KNOBS ARE TURNED
TO 0 (OFF).
BEFORE THE APPLIANCE IS PUT INTO OPERATION, ALL THE PROTECTIVE
FILMS APPLIED ON THE OUTSIDE MUST BE REMOVED.
The manufacturer declines all responsibility for injury or damage caused by failure to
comply with the above regulations or deriving from tampering with even just one part
of the appliance and the use of non-original spare parts.

7
Instructions for the user
4. GET TO KNOW YOUR OVEN
5. BEFORE INSTALLATION
CONTROL PANEL
OVEN LIGHT
OVEN FAN
SHELF AND TRAY RUNNERS
TEMPERATURE SENSOR
Never leave packaging residues unattended in the home. Separate waste
packaging materials by type and consign them to the nearest separate
disposal centre.
The inside of the appliance should be cleaned to remove all manufacturing
residues. For further information about cleaning, see point "11.
CLEANING AND MAINTENANCE".
When the oven and grill are used for the first time, they should be heated
to the maximum temperature for long enough to burn off any oily residues
left by the manufacturing process, which might contaminate foods with
unpleasant smells. After an interruption in the electricity supply, the
programmer display flashes at regular intervals. For setting instructions,
see point "7.3 First use".

8
Instructions for the user
6. DESCRIPTION OF FRONT PANEL CONTROLS
All the appliance's control and monitoring devices are placed together on
the front panel. The table below provides the key to the symbols used.
THERMOSTAT-TIMER KNOB
PT1 This knob allows you to set the time, select the
cooking temperature and duration and program
the cooking start and end times. From now on,
for convenience it will be referred to as PT1.
For instructions on how to use it correctly, see
point “7.3 First use” and “7.5 Programmed
cooking procedures”.
DISPLAY
DSP1 With the oven off, the 4-figure LED display shows the current time; when
the oven is in operation, it shows the temperature set and the cooking
duration set.
The display also contains the function cutout light (see point “7.6
Secondary menu”), the timer pilot light , the symbols relating to the
programmed cooking operations , and the setting of time .
From now on, for convenience it will be referred to as DSP1.

9
Instructions for the user
FUNCTION-SWITCH ON KNOB
PT2 Simply turn this knob to the right or left to select the function required, from
those listed below.
From now on, for convenience it will be referred to as PT2.
PT2
The table below provides a short description of the functions available:
NO FUNCTION SET GRILL ELEMENT
GRILL ELEMENT IN OPERATION
ALTERNATING WITH BOTTOM
HEATING ELEMENT + FAN
TOP + BOTTOM HEATING
ELEMENTS+FAN
BOTTOM HEATING ELEMENT GRILL ELEMENT + FAN
PIZZA FUNCTION BOTTOM HEATING ELEMENT +
FAN
TOP + BOTTOM HEATING
ELEMENTS
DEFROSTING

10
Instructions for the user
7. USING THE OVEN
7.1 Precautions and General Advice
All cooking operations must be carried out with the door closed
When the oven and grill are used for the first time, they should be heated
to the maximum temperature for long enough to burn off any oily residues
left by the manufacturing process, which might contaminate foods with
unpleasant smells.
During cooking, do not cover the bottom of the oven with aluminium
or tin foil, and do not place pans or trays on it; this may damage the
enamel coating. If you wish to use greaseproof paper, position it so
that it does not interfere with the hot air circulation inside the oven.
Oven accessories which may come into contact with foods are made from
materials compliant with directive 89/109/EEC of 21/12/88 and relevant
national regulations.
To avoid unpleasant contact with any steam inside
the oven, open the door in two stages: hold it half-
open (about 5 cm) for 4-5 seconds, then open it
completely. If you have to carry out any procedures
on foods, leave the door open for as short a time as
possible to prevent a drop in the oven temperature
which will impair the cooking results.
To prevent excessive amounts of condensation from forming on the
internal glass, food should not be left inside the oven for too long after
cooking.
7.2 Operating modes
This appliance is programmed to provide 3 operating settings:
OFF setting: obtained with knob PT2 turned to the “0” symbol; the current
time appears on the display.
ON setting: obtained with selector knob PT2 turned to any function; the
temperature set appears on the display.
Standby setting: obtained with selector knob PT2 turned to any function
and a timed cooking operation set; the current time appears on the display.

11
Instructions for the user
7.3 First use
At first use, or after a power failure, the oven display (DSP1), will show a
flashing symbol. To start any cooking operation, the current time
must be set.
(For further information about setting or adjusting the current time, see
point "7.6 Secondary menu").
7.4 Selecting the function
To select a cooking function, turn PT2.
Then select the temperature required using knob PT1
7.4.1 Cooking with preset temperature
After selection of the function required, the oven will start the cooking
procedure at the preset temperature. Cooking itself is preceded by a
preheating stage (common to all functions) which allows the oven to
heat to the cooking temperature more quickly.
The symbol flashes on the display (DSP1) to indicate that this stage is
in progress. When the preheating stage is over, the symbol will remain
constantly on to indicate that the food can be placed inside the oven.
7.4.2 Changing the preset temperature
The temperature preset for each function can be changed to suit the user's
requirements.
At any time while cooking is in progress, turn PT1 in either direction to
increase or decrease the cooking temperature by 5 degrees at a time. PT1
can also be held in the left or right position to increase or decrease the
setting more quickly.
7.5 Programmed cooking procedures
7.5.1 Timed cooking with minute minder
From ON status (see point “7.2 Operating modes”), press PT1 once. The
display will show the figures (constantly on) and the symbol
(flashing). Turn PT1 to set the minutes of cooking (from 00:01 to 23:59). A
few seconds later, the symbol will stop flashing, and the countdown will
start from that moment. Now you can also select the cooking function
required and wait for the buzzer to sound, indicating that the cooking time
is over.
Press PT1 once to stop the buzzer. You can now set an additional cooking
time by turning PT1, or return to display of the current time by pressing
PT1 twice.
Turn PT2 to the "0" symbol to switch the oven off completely.
The minute minder also works with no function set.

12
Instructions for the user
Warning. The minute minder does not stop the cooking process. It only
warns the user that the preset number of minutes have passed.
To switch the oven off completely, turn PT2 to the "0" symbol.
Modifying the data set
Once the countdown has started, its duration can be changed while
cooking is in progress.
When the symbol is steady, press PT1 once. The symbol starts
flashing and PT1 can be turned to change the set duration. A few seconds
after the last change, the symbol will stop flashing, and the countdown
will restart from the new value.
To change the preset temperature, wait for the symbol to become
steady and turn PT1 to the right or left to increase or decrease the cooking
temperature.
7.5.2 Semiautomatic cooking
Semiautomatic cooking is the function which allows a cooking operation to
be started and then ended after a specific length of time set by the user.
Select a cooking function (see point “7.4 Selecting the function”) and press
PT1 twice. The display will show the figures and the symbol
(flashing).
Turn PT1 to the right or left to set the minutes of cooking (from 00:01 to
23:59). A few seconds after the required duration is set, the symbol will
stop flashing, and semiautomatic cooking will start from that moment. At
the end, the word STOP will appear on DSP1, cooking will stop and a
buzzer will sound; press PT1 once to deactivate it.
If you wish to continue cooking beyond the set time, press PT1 again. The
oven will restart normal operation with the cooking settings selected
previously.
Turn PT2 to the "0" symbol to switch the oven off completely.
Modifying the data set
Once semiautomatic cooking has started, its duration can be changed.
When the symbol is steady, press PT1 once. The symbol starts
flashing and PT1 can be turned to change the set duration. A few seconds
after the last change, the symbol will stop flashing, and semiautomatic
cooking will restart from the new value.
To change the preset temperature, wait for the symbol to become
steady and turn PT1 to the right or left to increase or decrease the cooking
temperature.

13
Instructions for the user
7.5.3 Automatic cooking
Automatic cooking is the function which allows a cooking operation to be
started at a set time and then ended after a specific length of time set by
the user.
Select a cooking function, set the cooking temperature required or leave
the preset temperature (see point “7.4 Selecting the function”) and press
PT1 twice. The display will show the figures and the symbol
(flashing).
Turn PT1 to the right or left to set the minutes of cooking (from 00:01 to
23:59).
For reasons of safety, when setting automatic cooking the user must first
program a cooking duration and then set the cooking start time. It is not
possible to set the cooking start time only, without setting the cooking
duration.
After setting the duration, press PT1 once.
The symbol and the current time will appear on the display.
Turning PT1 to the right increases the time, allowing the cooking start
time required to be set.
A few seconds after the required duration is set, the and symbols
will stop flashing, and the oven will start to wait for the starting time set. At
the end, the word STOP will appear on DSP1, cooking will stop and a
buzzer will sound; press PT1 once to deactivate it.
If you wish to continue cooking beyond the set time, press PT1 again. The
oven will restart normal operation with the cooking settings selected
previously.
Turn PT2 to the 0 to switch the oven off completely.
Modifying the data set
Once automatic cooking has started, its duration can be changed.
When the and symbols are steady and cooking is in progress, or
the oven is in standby status waiting for cooking to start, press PT1 once.
The symbol starts flashing and PT1 can be turned to change the set
duration.
Press PT1 again; the symbol goes out, the symbol will start to
flash, and the cooking start time will be displayed on DSP1. The cooking
start time can be increased or decreased by turning PT1.
A few seconds after the last change, the e symbols will appear (in
steady mode) on DSP1 and automatic cooking will restart with the new
settings.

14
Instructions for the user
7.6 Secondary menu
This appliance also has a "secondary menu" allowing the user to:
1 Set the time shown on the display (DSP1).
2(P1: OF / ON) Activate or deactivate the child safety lock ( ; this
function locks out all the functions and knobs after 2 minutes of
operation without any command from the user (when this system is
active, the symbol appears on DPS1). To exit the lockout status
temporarily to modify a cooking program or select a different function,
keep PT1 pressed until the symbol disappears from DSP1. The
required changes can now be made, and 2 minutes after the last
setting is made the lockout will come into operation again. To
deactivate the lockout permanently, access the secondary menu and
switch the function off as described in this section.
3(P2: OF / ON) Activate or deactivate the Show Room function, which
disables all the heating elements so that only the control panel works.
To allow the oven to be used normally, P2:OFF must be set.
4(P3: OF / ON) Activate or deactivate the function which limits the
maximum power absorption to 2300 W.
When the child safety lock is activated (P1:ON), if a knob is turned
“bLOC” appears on DSP1 for 2 seconds. Operating PT2 also triggers the
“BLOC” alarm until the function originally selected is restored.

15
Instructions for the user
7.6.1 Modifying the secondary menu settings
The secondary menu appears the first time the appliance is used or after
a power blackout, or can be accessed by keeping PT1 depressed for 3
seconds with the oven in OFF status (see point “7.2 Operating modes”).
Changing the settings of the secondary menu parameters is very easy.
Refer to the chart below:
Turn PT1 to the
right to increase
(+) the value or
set ON status .
Turn PT1 to the left
to decrease ( - ) the
value or set Off
status .
Press PT1 to move
on to setting of the
next parameter in
the menu. After
setting P3, pressing PT1
returns to normal oven
operation.
SYMBOLSMENU MODIFICATION PROCEDURE

16
Instructions for the user
7.7 Cooling fan system
The appliance is equipped with a cooling
system which comes into operation as
soon as a cooking function or a cleaning
cycle (Pyrolysis) starts.
Operation of the fans generates a normal
air flow which comes out above and
underneath the door and may continue
for a short time even after the oven is
switched off.
7.8 Inside light
The oven light comes on:
• when the function knob is turned to any function.
• turning the knob PT1 on . Turning it to the left, it goes out.

17
Instructions for the user
8. USING THE PIZZA FUNCTION (ON SOME MODELS ONLY)
This appliance is equipped with a function specially developed for cooking
pizza. This function is identified by the symbol on the oven functions
knob. To cook a pizza, proceed as described below.
With the oven cold, remove the circular cover from the bottom of the
oven (fig. 1) and fit the pizza plate in its place (Fig. 2).
1) 2)
Set the oven functions knob on the symbol and the thermostat knob on
280°C. Preheat with these settings until the thermostat light goes out, then
place the pizza on the special plate. It does not normally take more than 3-
4 minutes to cook a pizza to perfection, although this time may vary
depending on the dough used or individual taste.
8.1 Precautions for using the pizza plate
• Never use the pizza plate except as described above (for example,
never use it on gas or ceramic hobs, or on ovens not designed to take
this accessory).
• The pizza plate may be left in place while conventional cooking
operations are in progress. Simply place the cover over it, taking care
to fit it securely.
• Never use any oven function if the pizza plate or cover is not in
position.
• The appliance becomes very hot during use. Oven gloves should
always be worn.
• If you like oil on your pizza, it is best to add it after removal from the
oven since oil stains on the pizza plate are unsightly and may reduce
its efficiency.

18
Instructions for the user
8.2 To save energy
The pizza stone acts as a heat reservoir. This allows energy consumption
to be reduced, especially in cooking operations requiring pre-heating or
medium-long times. In these cases, simply turn the thermostat to zero 10-
12 minutes before the end of the cooking time. The heat gradually emitted
by the refractory stone will ensure that the cooking temperature is
maintained.

19
Instructions for the user
9. ACCESSORIES AVAILABLE
The oven is fitted with 4 runners for placing
trays and shelves at different heights.
Shelf: useful to support pans containing the
food for cooking.
Tray grid: for placing on top of a tray for
cooking foods which may drip.
Oven tray: useful for collecting fat from foods
placed on the grid above.
Baking tray: useful for cooking cakes, pizza
and confectionery.
Pizza plate (on some models only)specially
designed for cooking pizza. For use as
described in point “8. USING THE PIZZA
FUNCTION (on some models only)”
Roof liner: remove it to simplify cleaning
inside the oven.
Chromium-plated gripper: useful for
removing hot shelves and trays.
Not all accessories are provided on some models.
Optional accessories
Original accessories can be ordered through our Authorised Service
Centres.

20
Instructions for the user
10. RECOMMENDED COOKING TABLES
The oven must be preheated before all cooking operations.
Do not place the foods inside the oven until the degrees Centigrade
symbol on the display stops flashing and the beep has sounded to confirm
that the set temperature has been reached.
Cooking times, for meat in particular, vary depending on the food's
thickness and quality and personal preference. All times are calculated
with the oven preheated.
CONVENTIONAL COOKING
RUNNER POSITION FROM
THE BOTTOM TEMPERATURE °C. TIME IN MINUTES
PASTA
LASAGNE
PASTA BAKES 1
1220 - 230 220 - 230 50 - 60 40
MEAT
ROAST VEAL
LOIN OF PORK
SHOULDER OF PORK
RABBIT
TURKEY BREAST
ROAST NECK OF PORK
2
2
2
2
2
2
190 - 200
190 - 200
190 - 200
190 - 200
190 - 200
190 - 200
80 - 90
80 - 90
100 - 110
70 - 80
160 - 180
190 - 210
FISH 1 - 2 160 - 170 Depending on size
PIZZA 1 - 2 250 20 - 25
BREAD 1 - 2 200 - 210 40
MUFFINS 2190 - 200 20 - 25
CONFECTIONERY
SPONGE CAKE
FRUIT TART
PASTRY
CROISSANTS
JAM TARTS
RICE CAKE
ANGEL CAKE
ECLAIR
LIGHT SPONGE CAKE
1 - 2
1 - 2
1 - 2
1 - 2
1 - 2
1 - 2
1 - 2
1 - 2
1 - 2
160 - 170
160 - 170
160 - 170
160 - 180
160 - 170
160 - 170
160 - 170
160 - 170
160 - 170
55 - 60
30 - 40
20 - 25
25 - 30
30 - 35
60
60
40 - 45
40 - 45

21
Instructions for the user
HOT AIR COOKING
RUNNER POSITION FROM
THE BOTTOM TEMPERATURE °C. TIME IN MINUTES
PASTA
LASAGNE
PASTA BAKES 2
2210 - 230 210 - 230 45 - 50 25 - 30
MEAT
ROAST VEAL
LOIN OF PORK
SHOULDER OF PORK
RABBIT
TURKEY BREAST
ROAST CHICKEN
2
2
2
2
2
2
180 - 190
180 - 190
180 - 190
180 - 190
180 - 190
180 - 190
70 - 80
70 - 80
90 - 100
70 - 80
110 - 120
60 - 70
FISH
SALMON TROUT 2150 - 160 35 - 40
PIZZA 1 - 2 250 15 - 20
BREAD 1190 - 200 25 - 30
MUFFINS 1 - 2 180 - 190 15 - 20
CONFECTIONERY
SPONGE CAKE
LARGE JAM TART
PASTRY
CROISSANTS
JAM TARTS
ANGEL CAKE
2
2
2
2
2
2
160
160
170
160 - 170
160
160
50 - 60
25 - 30
20 - 25
20 - 25
20 - 25
60
PROVING - DEFROSTING
TEMPERATURE °C
DEFROSTINGFOODS 30
NATURALYEASTDOUGHS 35 - 40
For successful proving, a container of water should be placed in the bottom of the
oven.

22
Instructions for the user
GRILLING
RUNNER POSITION FROM
THE BOTTOM TIME IN MINUTES
1ST SIDE 2ND SIDE
PORK CUTLET
PORK FILLET
FILLET STEAK
SLICED LIVER
VEAL ESCALOPES
HALF CHICKEN
SAUSAGE
MEATBALLS
FISH FILLET
TOASTED SANDWICHES
4
3
3
4
4
3
3
3
3
3
7 - 9
9 - 11
9 - 11
2 - 3
7 - 9
9 - 14
7 - 9
7 - 9
5 - 6
2 - 4
5 - 7
5 - 9
9 - 11
2 - 3
5 - 7
9 - 11
5 - 6
5 - 6
3 - 4
2 - 3