Smith DA007 User manual

DA007

6
14
15
16

─ 3 ─
Important Safety Instructions
Before beginning any fitness program, you should obtain a complete
physical examination from your physician. When using exercise equipment,
basic precautions should always be taken, including the following:
* Read all instructions before using the equipment. These instructions are
written to ensure your safety and to protect the unit.
* Do not allow children on or near the equipment.
* Use the equipment only for its intended purpose as described in this
guide. Do not use accessory attachments that are not recommended by
the manufacturer: such attachments might cause injuries.
* Wear proper exercise clothing and shoes for your workout----no loose
clothing.
* Be careful when getting on or off the equipment.
* Do not overexert yourself or work to exhaustion.
* If you feel any pain or abnormal symptoms, stop your workout immediately
and consult your physician.
* Never operate the unit when it has been dropped or damaged.
* Never drop or insert anything into any opening in the equipment.
* Always check the unit and its cables before each use. Make sure that all
fasteners and cables are secure and in good working condition.
* Frayed or worn cables can be dangerous and may cause injury.
Periodically check these cables for any indication of wear.
* Keep hands, limbs, loose clothing and long hair well out of the way of
moving parts.
* Do not attempt to lift more weight than you can control safely.
* Do not use the equipment outdoors.
Personal Safety During Assembly
* Read each step in the assembly instructions and follow the steps in
sequence. Do not skip ahead. If you skip ahead, you may learn later that
you have to disassemble components and that you may have damaged
the equipment.
* Assemble and operate the equipment on a solid, level surface. Locate the
unit a few feet from walls or furniture to provide easy access. The
equipment is designed for your enjoyment. By following these precautions
and using common sense, you will have many safe and pleasurable hours
of healthful exercise with the equipment.

Instructions
Before beginning assembly please take the time to read instructions
thoroughly. Please use the various lists in this manual to make sure that all
parts have been included in your shipment. When ordering, use part number
and description from the lists. Use only our replacement part when servicing.
Failure to do so will void your warranty and could result in personal injury.
The equipment is designed to provide the smoothest, most effective
exercise motion possible. After assembly, you should check all functions to
ensure correct operation. If you experience problems, first recheck the
assembly instructions to locate any possible errors made during assembly. If
you are unable to correct the problem, call your authorized dealer. Be sure to
have your serial number and this manual when calling. When all parts have
been accounted for, continue on.
Tools Required
Ratchet Wrench and Socket
Adjustable Wrench
Rubber Mallet
Hex Key Wrench Set
─ 4 ─

Item No. Description Qty Item No. Description Qty
1Weight Stack Frame 1 37 Plug F38 1
2Main Frame 1 38 Cushion 1
3Bottom Cross Brace 1 39 4.5" Pulley 6
4Rear Cross Brace 1 40 Bearing Φ50.8*Φ25.4*15.9 2
5Rotary Arm Frame 1 41 Flat Head Hex Rivet Nuts M10*19.5 4
6Handle Frame 2 42 Flat Head Cap Screw M10*25 4
7 Fixing Sleeve 2 43 Socket Head Cap Screw M10*50 4
8Seat Pad Support 1 44 Socket Head Cap Screw M10*25 2
9 Swing Tube 1 45 Button Head Cap Screw M10*15 4
10 Adjustable Support 1 46 Hex Head Bolt M10*130 4
11 Counter Poise Block 1 47 Hex Head Bolt M10*95 2
12 Grip 2 48 Hex Head Bolt M10*80 1
13 Front shroud 1 49 Hex Head Bolt M10*75 3
14 Rear Shroud 1 50 Hex Head Bolt M10*50 1
15 Cable 1 51 Hex Head Bolt M10*30 6
16 L Bracket 2 52 Hex Head Bolt M10*20 12
17 Aluminium Grip Ring φ90*φ26.2*5 4 53 Flat Washer φ11*φ20*1.5 41
18 Aluminium Grip Cap 2 54 Flat Washer φ9*φ16*1 2
19 Aluminium Grip Ring 2 55 Flat Washer φ5.3*φ10*1 4
20 Big Aluminous Cap φ60*φ12.5*10.6 2 56 Flat Washer φ11*φ38*2 2
21 Bushing 4 57 Nylon lock Nut M10 18
22 Guide Rod 2 58 Socket Set Screw M8*10 4
23 Fixing Sleeve 2 59 Socket Head Cap Screw M8*30 1
24 Sleeve 2 60 Socket Head Cap Screw M8*50 2
25 Main Shaft 1 61 Button Head Cap Screw M8*45 1
26 Aluminium Cap φ50*8 2 62 Nylon lock Nut M8 3
27 Spring φ13*14*1.8 1 63 Button Head Cap Screw M6*12 2
64 Hex Nut M6 2
29 Plastic Tube Guide 2 65 Cross Recess Pan Head Screw M5*12 4
30 Seat Pad 1 66 Socket Set Screw M5*3 8
31 Back Pad 1 67 Weight Plate 5KG 15
32 FOAM Pad 2 68 Top Plate 1
33 Top Shroud 1 69 Selector Pin W/Coil 1
34 Pulley Cover 8 70 Weight Rubber Bumper 2
35 Rubber Foot 4 71 Connection Frame 1
36 Plug RT50*100 2 72 Spring Washer φ10 4

14
5252
5353
5757
5353
5353
5757
28
13
33
5858
60 6262
23
23
60
2222
30
8
5353
5151
3535
35
35
4646
5353
656555
55
6565
55
55
1
5757
5353
24
3939
16
53
50
16
53
48
53
52 5353
5757
5353
52
5252
53
57 34
39 34 43
4747
5353
5757
53
53
31
4
42
20
1732
5858
9
32
17
20
42
61
54
27
10
54
35353
5757 2929
59
63
63
5353
11
51
51
40
25
40
53
53
72 52
72 52
5252
72
53
72
53
5
38
43
34
39
34
57
71
52
56
7
44
4545
6
19
6666
5353
5757
12
43
39
34
57
49
53
5353
5151
2
5353
4949
4545
52
56
44
7
6
19
1218
6666
6666
43
39
34
57
26
42
26
42
4646
5353
6666
18
70
67
68
69
70
6

7

8

9
4747
5353
1
49
53
57
53
57
53
57
53
57
53
46
53
2
8
46
53
5
42 26
26
42
71
38
53 72 52
52
72
53
3
4
25
59
1.Attach the Bottom Cross Brace(#3) to the Main Frame (#2) using:
two M10*130 HHB (#46) four φ11*φ20*2 Flat Washer (#53)
two M10 Nylon lock Nut (#57)
2.Attach the Rear Cross Brace(#4) to the Main Frame (#2) using:
two M10*130 HHB (#46) four φ11*φ20*2 Flat Washer (#53)
two M10 Nylon lock Nut (#57)
3.Attach the Bottom Cross Brace(#3) to the Weight Stack Frame (#1) using:
two M10*95 HHB (#47) four φ11*φ20*2 Flat Washer (#53)
two M10 Nylon lock Nut (#57)
4.Attach the Rear Cross Brace(#4) to the Weight Stack Frame (#1) using:
two M10*75 HHB (#49) four φ11*φ20*2 Flat Washer (#53)
two M10 Nylon lock Nut (#57)
5.Attach the Seat Pad Support (#8) to the Main Frame (#2) using:
one M8*30 SHCS (#59)
6.Attach the Rotary Arm Frame (#5) to the Main Frame (#2) using:
one Main Shaft (#25) two φ50*8 Aluminium Cap (#26)
two M10*25 FHCS (#42)
7.Attach the Connection Frame (#71) to the Rotary Arm Frame (#5) using:
four M10*20 HHB (#52) four φ11*φ20*1.5 Flat Washer (#53)
four φ10 Spring Washer (#72)

1
7070
69
67
68
2222
5858
6262
23
23
60
60
10
1.Attach:
two Guide Rod (#22) two φ63.5*25.4 Weight Rubber Bumper (#70)
fifteen SYD-JZJ 5KG （#67） one Top Plate （#68）
to the Weight Stack Frame (#1) using:
two Fixing Sleeve (#23) two M8*50 SHCS (#60)
two M8 Nylon lock Nut (#62) two M8*10 Socket Set Screw (#58)
2.Attach the Selector Pin W/Coil (#69) to the Top Plate （#68）

48
50
16
53
53
16
24
39
24
53
57
53
57
43
43
34
34
39
39
34
57
57
34
43
34
39
34
57
57 34
39
43
2
5
39
1
15
15
15
15
68
71
2
1.Attach the Cable (#15) to the Top Plate (#68).
2.Attach three 4.5" Pulley (#39) to the Weight Stack Frame (#1) using:
two L Bracket (#16) two φ20*φ16*19.3 Sleeve (#24)
one M10*50 HHB (#50) one M10*80 HHB (#48)
one M10*50 SHCS (#43) two Pulley Cover (#34)
four φ11*φ20*2 Flat Washer (#53) three M10 Nylon lock Nut (#57)
3.Attach two 4.5" Pulley (#39) to the Main Frame (#2) using:
two M10*50 SHCS (#43) four Pulley Cover (#34)
two M10 Nylon lock Nut (#57)
4.Attach one 4.5" Pulley (#39) to the Connection Frame (#71) using:
one M10*50 SHCS (#43) two Pulley Cover (#34)
one M10 Nylon lock Nut (#57)
5.Attach the Cable (#15) to the Main Frame (#2).
11

53 5151 53
51 53 11
42
20
17
32
17
9
585817
32
17
20
42
53
51
53
51
4953
30
31
5
2
8
1.Attach the Seat Pad (#30) to the Seat Pad Support (#8) using:
two M10*30 HHB (#51) two φ11*φ20*2 Flat Washer (#53)
2.Attach the Back Pad (#31) to the Main Frame (#2) using:
two M10*30 HHB (#51) one M10*75 HHB (#49)
three φ11*φ20*2 Flat Washer (#53)
3.Attach the Counter Poise Block (#11) to the Rotary Arm Frame (#5) using:
two M10*30 HHB (#51) two φ11*φ20*2 Flat Washer (#53)
4.Attach the Counter Poise Block (#32) to the Main Frame (#2) using:
one Swing Tube (#9) four φ90*φ26.2*5 Aluminium Grip Ring (#17)
two M8*10 Socket Set Screw (#58) two M10*25 Flat Head Cap Screw (#42)
two φ60*φ12.5*10.6 Big Aluminous Cap (#20)
12
2

13
14
5252
5353
5757
5353
57 575353
6565
5555
33
1
53
5252
53
53 52
53
52
1.Attach the Front Shroud (#13) to the Weight Stack Frame (#1) using:
four M10*20 HHB (#52) four φ11*φ20*2 Flat Washer (#53)
2.Attach the Rear Shroud (#14) to the Weight Stack Frame (#1) using:
two M10*20 HHB (#52) six φ11*φ20*2 Flat Washer (#53)
four M10 Nylon lock Nut (#57)
3.Attach the Top Shroud (#33) to the Weight Stack Frame (#1) using:
four M5*12 BHCS (#65) four φ10*φ5.3*1 Flat Washer (#55)
13

14

15

16