Snapper P217017BVE User manual

Parts Manual fo
r
Revision 4,
21" STEEL DECK WALK BEHIND MOWERS
SERIES 17
COPYRIGHT
©
2006
McDonough, GA, 30253 U.S.A.
TP 400-5002-4-WB-N
1/16/2006 Manual No. 7006136
SNAPPER PRODUCTS, INC.
ALL RIGHTS RESERVED.
PUSH MODELS PROPELLED
MODELS
216517B P215517HC
2167517BV P216517B
R215517HC P2167517BV
R2167517BV P2167517BVE
P217017BV
P217017BV
E
RP215517HC
RP2167517BV
RP217017BV
RP2167517BVE
RP217017BVE
WP2167517BV
WP216517BV
WRP216517BE
FRP2167517BV
EP2167517BV
EP217017BV
ERP2167517BV
ERP217017BV
EFRP2167517BV
WRPS216517B
WRPS216517BE

Table Of Content
s
TP 400-5002-4-WB-N
Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS
SERIES 17 3
PAGE GROUP
4HANDLES & CONTROLS
8CUTTING DECK, BLADES
12 FRONT WHEEL BRACKET
14 SWIVEL CASTER ASSEMBLY
16 REAR WHEEL BRACKETS, LATCHES
18 FRONT WHEELS
20 FRONT WHEELS - SWIVEL MODEL
22 REAR WHEELS
24 DRIVE SYSTEM SELF-PROPELLED PT.1
28 TRANSMISSION (DIFFERENTIAL)
30 THROTTLE CONTROLS
32 KIT, MUFFLER DEFLECTOR
34 ENGINE SPECIFICATIONS
36 SIDE CHUTE, ADAPTER
38 GRASS BAG ACCESSORY
40 DECALS PT. 1
42 DECALS PT. 2
44 SNAPPERIZER ACCESSORY
46 THATCHERIZER ACCESSORY
48 RECYCLING KITS ACCESSORY
50 ELECTRIC START COMPONENTS
52 WIRING SCHEMATIC

HANDLES & CONTROLS
TP 400-5002-4-WB-N
Manual No. 7006136 21" STEEL DECK WALK BEHIND MOWERS
SERIES 17
4

HANDLES & CONTROLS
Footnotes:
TP 400-5002-4-WB-N
Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS
SERIES 17 5
Part No Descri
p
tionItem Qt
y
Note
1 7074254 1 HANDLE, Upper Was 72931 (used on Push
Models)
-- 7074254 1 HANDLE, Upper used on Self-Propelled
2 7036350 1 HANDLE, Middle- 1990 used on All
3 7046502 1 HANDLE, Lower Left Hand used on All
4 7035342 1 HANDLE, Lower Right Hand used on All
5 7047011 1 BAIL, Blade Control used on All
6 7033904 1 CLIP, Blade Control used on 2002 Models & Earlier
-- 7034872 1 CLIP, Blade Control used on 2003 Models & Later
7 7072933 1 CABLE, Blade Control (49-1/4” long) used on 2002 Models & Earlier
-- 7074868 1 CABLE, Blade Control (46-15/16” long) used on 2003 Models & Later
-- 7074830 1 CABLE, Blade Control (49” long) used on Honda 2003 Models &
Later
8 7032826 1 HANDLE, Wheel Drive used on Self-Propelled
9 7014307 1 GRIP, Wheel Drive Handle used on Self-Propelled
-- 7029775 1 GRIP, Wheel Drive Handle used on European Models
10 7072932 1 CABLE, Clutch Pull (Z-Bend, 38-5/8” long) used on Self-Propelled
11 7012121 1 COVER, Vinyl used on Self-Propelled
12 7012122 1 SPRING, Clutch used on Self-Propelled
13 7038478 1 SECTOR, Speed used on all other Self-Propelled
models
14 7024641 3 WIRE TIE, 1.29” Long (Black) used on Self-Propelled
15 7012093 1 SPRING, Speed Control used on Self-Propelled
16 7090188 1 WASHER, 3/8” Flat used on Self-Propelled
17 7023801 1 GRIP, Speed Control Handle used on all other Self-Propelled
models
18 7032830 1 ANCHOR, Speed Control used on all other Self-Propelled
models
19 7032408 1 GUIDE, Lower V-Belt used on Self-Propelled
20 7023790 1 ROD, Transfer used on Self-Propelled
20A 7051698 1 ASSEMBLY, Transfer Rod used on European Models
21 7010937 1 CLIP, Transfer Rod 1/4” used on Self-Propelled
22 7090895 1 TEE-NUT, 5/16-18 used on Self-Propelled
23 7012114 1 BUSHING, Differential used on Self-Propelled
24 7090595 1 BOLT, 5/16-18 x 3/4” Hex Flange Lock GR5 used on All
25 7090238 1 SCREW, 5/16-24 x 1” Hex Head Cap GR5 used on All
26 7090799 1 BOLT, 5/16-18 x 5/8” Short Neck Carriage GR5 Was 91026 (used on All)
27 7091601 10 NUT, 5/16-18 Hex Flange Lock GR5 Was 91070 (used on All)
28 7091606 1 NUT, 5/16-24 Hex Center Lock GR5 Was 91074 (used on All)
29 7023813 1 CLIP, Cable/Wiring used on All
30 7091740 4 SCREW, 5/16-18 x 1-7/8” Curved Head GR2 Was 91189 (used on All)
31 7035744 4 T-KNOB, 5/16-18 (BLACK) used on All

HANDLES & CONTROLS
TP 400-5002-4-WB-N
Manual No. 7006136 21" STEEL DECK WALK BEHIND MOWERS
SERIES 17
6

HANDLES & CONTROLS
Footnotes:
TP 400-5002-4-WB-N
Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS
SERIES 17 7
Part No Descri
p
tionItem Qt
y
Note
32 7079577 2 SCREW, 1/4-20 x 1-1/2 Hex Head Cap GR5 used on All
33 7090053 3 WASHER, 1/4” Internal Tooth Lock Was 91023 (used on All)
34 7091576 3 NUT, 1/4-20 Hex GR5 or B Was 91100 (used on All)
35 7090505 1 SCREW, 1/4-20 x 2” Hex Head Cap GR5 used on All
36 7014343 4 BUSHING used on All
37 7023792 1 PIN, 1/4” x 1-1/2” (for clutch handle) used on Self-Propelled
38 7091020 1 PUSH-NUT, 1/4” (for handle pin) used on Self-Propelled
39 7024211 1 DECAL, Blade Control (Left Hand Side) used on all (except Euro)
-- 7029782 1 DECAL, Blade Control (Left Hand Side) used on European
-- 7029785 1 DECAL, Handle International Warning used on European
40 7026141 1 GUIDE, Rope used on All
41 7075634 1 FOAM GRIP, .84 I.D. x 11” long Was 73115
-- 7075634 1 FOAM GRIP, .84 I.D. x 12” long
42 7024087 1 DECAL, Speed Select used on Self-Propelled (except
Euro)
-- 7029783 1 DECAL, Speed Select (Euro) used on Self-Propelled (Euro)
43 7023153 1 CLAMP, Casing used on All
44 7090391 4 WASHER, 5/16” Internal Tooth Lock used on All
45 7090545 1 SCREW, 5/16-24 x 1-1/2” Round Hd. Machine, GR5 used on All
46 7022779 1 GUIDE, Rope used on All
47 7074255 1 LEVER, Speed Control used on Self-Propelled
48 7046465 1 GUIDE, Rope used on Self-Propelled
49 7076978 1 NUT, 1/4-20 Hex GR5 or B used on Self-Propelled
50 7012080 1 CABLE-TIE, 7” used on Self-Propelled
52 7023154 1 SCREW, #10-32 x 5/8” Hex Head Self-Tap used on All
51 7079577 1 SCREW, 1/4-20 x 1-1/2” Hex Head Cap, GR5 used on Self-Propelled
53 7024649 1 WIRE TIE, 11” Long (Black) used on Self-Propelled
-- 7090505 1 SCREW, 1/4-20 x 2” Hex Head Cap GR5 used on Self-Propelled
54 7026219 1 CLAMP, 7/8” Double Cable used on Self-Propelled
56 7072023 1 CONTROL, Swivel Wheel Lock Cable 56.5" used on Swivel Wheel

CUTTING DECK, BLADES
TP 400-5002-4-WB-N
Manual No. 7006136 21" STEEL DECK WALK BEHIND MOWERS
SERIES 17
8

CUTTING DECK, BLADES
Footnotes:
TP 400-5002-4-WB-N
Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS
SERIES 17 9
Part No Descri
p
tionItem Qt
y
Note
1 7057663 1 DECK, 21” Mower (“HV” deck w/decals)
-- 7058540 1 DECK, 21” Mower (Baffle Type deck w/decals) used on “FRP” & “EFRP” Air
Models only
-- 7057884 1 DECK, 21” Mower (“M” deck w/decals)
-- 7074949 1 DECK, 21” Mower (Swivvel wheel "M" deck w/o decals)
2 7091601 10 NUT, 5/16-18 Hex Flange Lock, GR5 Was 90585
3 7090731 10 BOLT, 5/16-18 x 1/2” Short Neck Carriage GR5
4 7091169 1 BOLT, 5/16-18 x 1-1/8” Short Neck Carriage GR5
5 7090324 3 SCREW, 3/8-16 x 1” Self-Tap (engine mounting screws)
6 7046780 2 PLUG, Hole
7 7090534 1 SCREW, 5/16-18 x 1/2” Hex Head Cap, GR5 used on Euro models
8 7090702 1 BOLT, 5/16-18 x 2-1/4” Hex Flange Lock used on Euro models
9 7013320 1 BUSHING used on Euro models
10 7033863 1 COVER, Belt used on Euro models
11 7031961 2 WASHER, 7/16” Flat used on Euro models
12 7090483 1 SCREW, 3/8-24 x 1-3/4 Hex Head Cap GR5
13 7012063 2 WASHER, 3/8” I.D. Cone
14 7019795 1 BLADE, Cutter (European) used on Euro models
14A 7017168 1 BLADE, Cutter (Mulching)
14B 7026691 1 BLADE, Cutter (Standard Lift)
14C 7026407 1 BLADE, 21” Ninja (Quad Edge)
15 7015626 1 HUB, Blade Drive 25mm used on Briggs Models
-- 7012927 1 HUB, Blade Drive 7/8” used on Honda Models
16 7015894 1 KEY, Woodruff # 605 used on Briggs Models
-- 7091214 1 KEY, Hi-Pro #HP506 used on Briggs Models
-- 7010783 1 KEY, Woodruff #505 Hi-Pro used on Honda Models
17 7090201 1 SCREW, 5/16-18 x 5/16” Hex Socket Set
18 7015780 1 PULLEY, Engine (25mm I.D. x 2-1/8” O.D.) used on Briggs Models
-- 7021764 1 PULLEY, Engine (7/8” I.D. x 2-1/8” O.D.) used on Honda Models
19 7031961 1 WASHER, 7/16” Flat
20 7041400 1 WELDMENT, Fender used on Euro models
21 7091508 2 BOLT, 5/16-18 x 3/4” Short Neck Carriage GR5 Was 90001 (only one shown)
22 7011791 2 RETAINER, 5/16” Bolt (only one shown)
23 7091601 3 NUT, 5/16-18 Hex Flange Lock, GR5 Was 91070
-- 7060785 1 KIT, Air Lift (Includes 4 items below)
24 7032558 2 LIFT, Air
25 7090391 4 WASHER, 5/16” Internal Tooth Lock
26 7091297 4 NUT, 5/16-24 Hex, GR5 Was 90223

CUTTING DECK, BLADES
TP 400-5002-4-WB-N
Manual No. 7006136 21" STEEL DECK WALK BEHIND MOWERS
SERIES 17
10

CUTTING DECK, BLADES
Footnotes:
TP 400-5002-4-WB-N
Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS
SERIES 17 11
Part No Descri
p
tionItem Qt
y
Note
27 7090228 4 SCREW, 5/16-24 x 21/32” Machine
28 7090951 2 NUT, 5/16-18 Hex Center Lock
29 7029193 1 DECAL, Front Baffle
30 7072426 1 BAFFLE, Front used on “FRP” & “EFRP” Air
Models only
31 7036463 1 DECAL, Front Baffle
32 7090316 2 BOLT, 5/16-18 x 3/4” Carriage, GR5
33 7090189 2 WASHER, 5/16” Internal/External Tooth Lock
34 7024085 2 WINGNUT, 5/16-18 Nyloc
35 7091076 1 WASHER, 5/16” Flat
36 7044770 1 SPACER, 1/16” Thick, Blade Hub
37 7074568 1 BAFFLE, Belt
38 7046471 3 PLUG, 5/16” Square Hole used on Push only
39 7045264 3 PLUG, 5/16” Round Hole Qty 3 on Push; Qty 2 on Self-
Propelled
40 7091122 4 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap Was 90539
41 7046720 1 DECAL, Warning Chute/Deflector

FRONT WHEEL BRACKET
TP 400-5002-4-WB-N
Manual No. 7006136 21" STEEL DECK WALK BEHIND MOWERS
SERIES 17
12

FRONT WHEEL BRACKET
Footnotes:
TP 400-5002-4-WB-N
Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS
SERIES 17 13
Part No Descri
p
tionItem Qt
y
Note
1 7051886 1 ASSEMBLY, Right Wheel Arm (Consists of items 2, 3, 4, 5A &
6)
-- 7051885 1 ASSEMBLY, Left Wheel Arm (Consists of items 2, 3, 4, 5B &
6)
2 7015761 2 BOLT, 5/16-18 Hex Washer Face Shoulder
3 7012325 2 LATCH, Height
4 7027702 2 GRIP, Latch
5A 7031017 1 ARM, Right Wheel (Round Hole)
5B 7031016 1 ARM, Left Wheel (Square Hole) not shown
6 7011791 2 RETAINER, 5/16” Bolt (Black)
7 7091601 2 NUT, 5/16-18 Hex Flange Lock Was 91070
8 7074702 1 WELDMENT, Front Wheel Bracket Was 41770, Used on 2002
Model Year and Earlier
-- 7074702 1 WELDMENT, Front Wheel Bracket used on 2003 Model Year and
Later
9 7021119 1 AXLE

SWIVEL CASTER ASSEMBLY
TP 400-5002-4-WB-N
Manual No. 7006136 21" STEEL DECK WALK BEHIND MOWERS
SERIES 17
14

SWIVEL CASTER ASSEMBLY
Footnotes:
TP 400-5002-4-WB-N
Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS
SERIES 17 15
Part No Descri
p
tionItem Qt
y
Note
1 7057782 1 WELDMENT, Front Bracket
2 7079577 1 SCREW, 1/4-20 x 1-1/2” Hex Cap
3 7090372 1 NUT, 1/4-20 Hex Lock
4 7072244 1 BRACKET, Swivel Lock
5 7046668 1 SPRING, Torsion
6 7090505 1 BOLT, 1/4-20 x 2” Hex
7 7027344 4 WASHER, 41/64” Flat Was 15992
8 7046628 4 BUSHING, 5/8” Nylon
9 7013864 2 LUBE FITTING, Straight (press-fit for .187 dia. Hole)
10 7076978 1 NUT, 1/4-20 Hex Lock
11 7014106 2 PIN, 1/4 x 1-3/4” Roll
12 7072229 1 WELDMENT, L.H. Swivel Bracket
7072230 1 WELDMENT, R.H. Swivel Bracket Was 57789 (Not Shown)
13 7072023 1 CONTROL, Swivel Wheel Lock Cable 56.5”

REAR WHEEL BRACKETS, LATCHES
TP 400-5002-4-WB-N
Manual No. 7006136 21" STEEL DECK WALK BEHIND MOWERS
SERIES 17
16

REAR WHEEL BRACKETS, LATCHES
Footnotes:
TP 400-5002-4-WB-N
Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS
SERIES 17 17
Part No Descri
p
tionItem Qt
y
Note
1 7012312 2 BALL BEARING, 9/16” I.D.
2 7091012 3 SCREW, #10-32 x 3/8” Hex Washer Self-Tap (Torx)
3 7035717 2 LATCH, Height Adjusting (Long)
4 7091576 1 NUT, 1/4-20 Hex Was 90063
5 7091601 6 NUT, 5/16-18 Hex Flange Lock, GR5 Was 91070
6 7054228 1 ASSEMBLY, Wheel Arm, Right Rear (Round hole) used on Push models (Incl.
items 3, 10, 14, 15 & 16)
7 7054229 1 ASSEMBLY, Wheel Arm, Left Rear (Square hole) used on Push models (Incl.
items 3, 11, 14, 15 & 16)
8 7054246 1 ASSEMBLY, Wheel Arm (Right Rear) Was 54230 (Self-Propelled
models)(Incl. 1, 2, 3, 12, 14, 15
& 16)
9 7054247 1 ASSEMBLY, Wheel Arm (Left Rear) Was 54231 (Self-Propelled
Models)(Includes 1, 2, 3, 13, 15,
& 16)
10 7033776 1 ARM, Round Axle End, Right Rear (Round hole) used on Push models
11 7033775 1 ARM, Square Axle End, Left Rear (Square hole) used on Push models
12 7032722 1 ARM, Wheel, Right Rear used on Self-Propelled models
13 7032723 1 ARM, Wheel, Left Rear used on Self-Propelled models
14 7011078 2 BOLT, 5/16-18 x 1” Shoulder
15 7011791 2 RETAINER, 5/16” Bolt
16 7027702 2 GRIP, Latch
17 7033494 1 BRACKET, Right Rear Wheel
18 7033495 1 BRACKET, Left Rear Wheel
19 7021119 1 AXLE Rear axle on Push Models;
Front axle on All Models
20 7035741 1 GUARD, Rear Foot used on Push models
21 7029008 1 GUARD, Rear Foot used on Self-Propelled models
(except European)
-- 7017010 1 GUARD, Rear Foot used on Euro Self-Propelled
models
22 7023791 1 RING, Split (Black) used on Self-Propelled models
23 7012616 1 SUPPORT, Foot Guard used on Self-Propelled models
24 7091604 1 BOLT, 1/4-20 x 1/2” Short Neck Carriage GR5 Was 90005 (used on Self-
Propelled models)
25 7090053 1 WASHER, 1/4” Internal Tooth Lock Was 91023
26 7090731 2 BOLT, 5/16-18 x 1/2” Short Neck Carriage GR5

FRONT WHEELS
TP 400-5002-4-WB-N
Manual No. 7006136 21" STEEL DECK WALK BEHIND MOWERS
SERIES 17
18

FRONT WHEELS
Footnotes:
TP 400-5002-4-WB-N
Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS
SERIES 17 19
Part No Descri
p
tionItem Qt
y
Note
1 7022374 2 WHEEL, 8 x 1.75 Plastic used on 2002 Model Year and
Earlier
2 7029010 2 WHEEL, 8 x 1.75 Plastic used on 2003 Model Year and
Later
3 7090377 2 NUT, 7/16-20 Hex Center Lock Jam (thin)
4 7012309 2 BUSHING, Axle
5 7031961 6 WASHER, 7/16 x 1” O.D. Flat Qty. of (2) for Push; Qty. of (1)
for Self-Propelled Models
6 7017829 2 PLUG, Wheel

FRONT WHEELS - SWIVEL MODEL
TP 400-5002-4-WB-N
Manual No. 7006136 21" STEEL DECK WALK BEHIND MOWERS
SERIES 17
20