SNORBLOK NITE-PRO User manual
NITE-PRO
ADJUSTABLE ANTI-SNORING
MOUTHPIECE
MANDIBULAR ADVANCEMENT TECHNOLOGY
Mandibular Advancement Devices, or MAD’s have been clinically proven to assist in the treatment of snoring and
mild Sleep Apnea.
The NitePro features a thermally moulded mouthpiece that custom fits to individual teeth patterns. It is adjustable in
fine increments so that the lower jaw is able to be positioned for maximum effectiveness.
WITH NITE-PRO
Aer moulding the NitePro to
your teeth, adjust the lower jaw
forward which helps open the
airway and reduce or eliminates
snoring.
WITHOUT NITE-PRO
Snoring oen happens by the so
ssue around the mouth and
throat area collapsing as the
muscles relax during sleep.
Thermal moulds
for an individual
custom fit
The top and boom plates
mould to the upper and
lower teeth independently
for a secure and comforta-
ble t .
Adjustable for
on-going
maximum
effectiveness
Adjustable in 1mm
increments without any
tools. Once adjusted, the
rigid frame maintains the
posion over me.
ADVANCED DESIGN FOR
SUPERIOR RESULTS
Rigid frame to
maintain shape
long-term
The NitePro has a rigid
frame consisng of 2
plates, a top and boom.
This ensures that the
mouthpiece doesn’t lose
its shape and eecveness
quickly like other replica
products.
www.snorblok.co.nz
10 TOOL FREE
ADJUSTABLE SETTINGS
The Snorblok NitePro’s secret lies in it’s adjustability
To adjust for the best t, simply press the buons either side of the
mouthpiece and the top and boom plates move and lock in 1mm
increments
ADJUSTMENT
BUTTON
STEP 1.
Place a cup or bowl of water in
the microwave and heat unl
nearly boiling.
STEP 2.
By pressing in the side adjustment tabs,
adjust the NitePro so that the lower jaw is
advanced slightly forward on the top jaw.
When you are moulding to your teeth, the
lower jaw should be slightly advanced
(forward) as that is the eect to be
achieved.
STEP 3.
Place the mouthpiece into the water
for around 30-40 seconds. Remove
with a pair of tongs to avoid burns.
Warning, do not place in water for too
long as the teeth mould will shrink up.
STEP 4.
When removed from the boiling water, place in a cup or bowl
of room temperature water for 2-3 seconds.
STEP 5.
Place in mouth. Position upper and lower teeth with the
lower jaw slightly forward and bite down hard to mould
the mouthpiece to the shape of your teeth.
If the mould is not soft enough, repeat with hotter water
until the correct softness is achieved to get a good
impression.
STEP 6.
Once moulded, place in cold water to lock the shape.
Adjust the jaw advancement position for maximum
effect. The process can be repeated if required.
FITTING INSTRUCTIONS
CARE INSTRUCTIONS
1. As the NitePro has moving parts with small crevices,
it is important that you take care to keep it clean
and free from bacteria.
Snorblok Mouthpiece & Denture Cleaner Tablets
are ideal for this as they kill 99.9% of all bad
bacteria and leaves your mouthpiece fresh and
ready to use.
We suggest that you cleanse at least once a week.
Many people wear during the night and soak during
the day.
2. The NitePro can be disassembled by holding in the
adjustment tab and sliding the upper and lower
palates apart. They can then be scrubbed with a
toothbrush or denture brush. Do not use your
normal tooth brush and rinse well before wearing.
3. Store in the sanitary container provided.
MOUTHPIECE &
DENTURE CLEANER
Snorblok Mouthpiece
& Denture Cleaner is
available on our
website
www.snorblok.co.nz.
Please read through instructions completely
and prepare everything prior to starting.
The purpose of the boil and bite system is to mould your
teeth into the top and bottom plates of the mouthpiece.
Care needs to be taken to ensure that the water isn’t too
hot, and that the exposure to the hot water isn’t
excessively long, to avoid the mould deforming.
