SnowEx HELIXX User manual

June 1, 2022
Lit. No. 31022EN, Rev. 00
This manual supersedes all editions with an earlier date.
CAUTION
Read this document before operating
or servicing the spreader.
HELIXX™ Stainless Steel
Hopper Spreader
0.35 yd³ for UTVs
Owner's Manual
Original Instructions
This Owner's Manual is for HELIXX Hopper Spreaders
with serial numbers beginning with 200706 and higher.

Lit. No. 31022EN, Rev. 00 3 June 1, 2022
TABLE OF CONTENTS
SAFETY ..................................................................... 5
Safety Denitions.................................................. 5
Warning/Caution Labels ....................................... 5
Serial Number Label ............................................. 9
Safety Precautions................................................ 9
Fuses .................................................................. 10
Personal Safety................................................... 10
Fire and Explosion .............................................. 10
Cell Phones......................................................... 11
Ventilation ........................................................... 11
Battery Safety ..................................................... 11
Noise................................................................... 11
Vibration.............................................................. 11
Torque Chart ....................................................... 11
LOADING ................................................................. 12
Certication......................................................... 12
Material Weights ................................................. 12
Spreader Specications...................................... 12
Load Volume ....................................................... 13
Determining Vehicle Payload.............................. 13
Determining Vehicle Payload Worksheet..... 14
UNPACKING THE SPREADER............................. 15
Remove Shipping Brackets and Locate
Components .................................................... 15
Chute Assembly.................................................. 15
MOUNTING THE SPREADER............................... 16
Install Hopper in Vehicle Bed.............................. 16
Install Tie-Down Straps ................................ 18
Construct Sill Spacer.................................... 18
SPINNER DRIVE ASSEMBLY............................... 19
Install Spinner Drive Assembly ........................... 19
OPERATING THE SPREADER – CAB CONTROL .. 20
Powering the Control .......................................... 20
Starting and Stopping Spreader ......................... 21
Controlling Material Application .......................... 21
BLAST/Maximum Application ...................... 22
Cab Control Modes.............................................22
Standby Mode .............................................. 22
Ready Mode ................................................. 22
ON Mode ...................................................... 23
Error Mode ................................................... 23
Cab Control Codes ............................................. 24
Setup Procedures ...............................................26
Calibrate the Empty Hopper Setting
(Cb and EH Codes) ................................... 26
OPERATING THE SPREADER ............................. 27
Auto-Reverse (Ar) Feature.................................. 27
Adjusting the Auto-Reverse (Ar) Setting ...... 27
Auto-Reverse (Ar) Sequence ....................... 27
Spreading Tips.................................................... 27
Accessory LED Work Light................................. 28
Dump Function.................................................... 28
REMOVING & STORING THE SPREADER......... 30
Remove Spreader from Vehicle.......................... 30
Store the Spreader..............................................30
MAINTENANCE ...................................................... 31
After First Use ..................................................... 31
After Each Use.................................................... 31
At End of Each Season or
After Extended Storage ................................... 31
Cab Control......................................................... 31
Fuse Replacement.............................................. 31
Recycle ............................................................... 31
ELECTRICAL COMPONENTS .............................. 32
Vehicle Harness Diagram ................................... 32
Electrical Control Box .........................................33
TROUBLESHOOTING GUIDE...............................34

Lit. No. 31022EN, Rev. 00 4 June 1, 2022
This manual has been prepared to acquaint you with
the safety information, operation, and maintenance of
your new hopper spreader. Please read this manual
carefully and follow all recommendations. This will
help ensure protable and trouble-free operation of
your hopper spreader. Keep this manual accessible. It
is a handy reference in case minor service is required.
When service is necessary, bring your hopper
spreader to your distributor. They know your spreader
best and are interested in your complete satisfaction.
NOTE: This spreader is designed to spread snow
and ice control materials only. Do not use it
for purposes other than those specied in this
manual.
Register your spreader online at www.snowexproducts.com
Owner Name: ______________________________________________________________________________
Date Purchased: ____________________________________________________________________________
Dealer Name: ______________________________________________ Phone: _________________________
Dealer Address:_____________________________________________________________________________
Vehicle Model/Year: _________________________________________________________________________
Spreader Model/Year: ________________________________________________________________________
Spreader Length ____________________________________________ Weight ____________________ lb/kg
Spreader Serial Number:______________________________________________________________________
Translated Owner's Manuals can be found online at
https://library.snowexproducts.com/default.asp?cat=387

Lit. No. 31022EN, Rev. 00 5 June 1, 2022
SAFETY
SAFETY
SAFETY DEFINITIONS
NOTE: Indicates a situation or action that can lead
to damage to your spreader and vehicle or other
property. Other useful information can also be
described.
WARNING/CAUTION LABELS
Become familiar with and inform users about the
warning and caution labels on the spreader.
NOTE: If labels are missing or cannot be read, see
your sales outlet.
CAUTION
Indicates a potentially hazardous situation
that, if not avoided, may result in minor or
moderate injury. It may also be used to alert
against unsafe practices.
WARNING
Indicates a potentially hazardous situation
that, if not avoided, could result in death or
serious personal injury.
30917EN.00
WARNING
No Step
Slippery surface when wet.
Falls may cause severe
injury.

Lit. No. 31022EN, Rev. 00 6 June 1, 2022
SAFETY
WARNING/CAUTION LABELS continued
30917EN.00
WARNING
No Step
Slippery surface when wet.
Falls may cause severe
injury.

Lit. No. 31022EN, Rev. 00 7 June 1, 2022
SAFETY
Translation of Safety Labels
Label Translation of Label Text
WARNING
• DO NOT exceed GVWR or GAWR with spreader and load.
• Turn spreader OFF before lling, adjusting or cleaning.
• Bystanders to stay a minimum of 25 feet away from operating spreader.
• DO NOT climb into or ride on spreader.
• Keep hands, feet and clothing away from moving conveyor and spinner.
CAUTION
• Read Owner's Manual before operating or servicing spreader.
• Empty and clean spreader after every use.
WARNING
Multiple Pinch Points
30917EN.00
WARNING
No Step
Slippery surface when wet.
Falls may cause severe
injury.
WARNING
No Step
• Slippery surface when wet.
• Falls may cause severe injury.
WARNING
Vehicles <10,000 lb GVWR
Obstructing the visibility from the vehicle's rear camera could result in serious injuryor
damage. An auxiliary camera systemshall be installed if the vehicle'srear camera is
removed or blocked.
Continued on next page

Lit. No. 31022EN, Rev. 00 8 June 1, 2022
SAFETY
Label Translation of Label Text
WARNING
Disconnect spinner harness before rotating chute up for dumping or storing.
WARNING
ROTATING AUGER CAN CAUSE SERIOUS INJURY OR DEATH
• Keep arms, hands, and loose clothing away from auger.
• Shut o󰀨 control and unplug spreader before servicing.
FEED
Press both buttons to operate.
ACCESSORY WORK LIGHT
SEE OWNER'S MANUAL FOR COMPLETE INSTRUCTIONS.
Press both buttons to operate.
FEED
SEE OWNER'S MANUAL FOR COMPLETE INSTRUCTIONS.
Translation of Safety Labels continued

Lit. No. 31022EN, Rev. 00 9 June 1, 2022
SAFETY
SERIAL NUMBER LABEL SAFETY PRECAUTIONS
Improper installation and operation could cause
personal injury and/or equipment and property
damage. Read and understand labels and the
Owner's Manual before installing, operating, or making
adjustments.
WARNING
• Driver to keep bystanders minimum of
25 feet (7.62 m) away from operating
spreader.
• Before working with the spreader, secure all
loose-tting clothing and unrestrained hair.
• Before operating the spreader, verify that all
safety guards are in place.
• Before servicing the spreader, wait for
conveyor, auger, and spinner to stop.
• Do not climb into or ride on spreader.
WARNING
Do not install the control for this product in
the deployment path of an air bag. Refer to
vehicle manufacturer's manual for air bag
deployment area(s).
WARNING
Overloading could result in an
accident or damage. Do not exceed
GVWR or GAWR ratings as found
on the driver-side vehicle door
cornerpost. See Loading section to determine
maximum volumes of spreading material.
Code Denition
YY 2-Digit Year
MM 2-Digit Month
DD 2-Digit Day
LL 2-Digit Location Code
XXXX 4-Digit Sequential Number
ZZZZZ 5- to 7-Digit Assembly Part Number
TrynEx International, LLC
531 Ajax Drive
Madison Heights, MI 48071
YYMMDDLLXXXXZZZZZ
HELIXX™ 00 YD³ SS HOPPER
WARNING
With chute removed, use dump switches to
operate conveyor.
WARNING
Vehicles <10,000 lb (4536 kg) GVWR:
Obstructing the visibility from the vehicle's
rear camera could result in serious injury or
damage. An auxiliary camera system shall
be installed if the vehicle's rear camera is
removed or blocked.

Lit. No. 31022EN, Rev. 00 10 June 1, 2022
SAFETY
CAUTION
If rear directional, CHMSL light, or brake
stoplights are obstructed by the spreader, the
lights shall be relocated, or auxiliary directional
or brake stoplights shall be installed.
CAUTION
Disconnect electric and/or hydraulic power
and tag out if required before servicing or
performing maintenance.
NOTE: Lubricate grease ttings after each use.
Use a good quality multipurpose grease.
FUSES
The electrical system contains several blade-style
automotive fuses. If a problem should occur and fuse
replacement is necessary, the replacement fuse must
be of the same type and amperage rating as the original.
Installing a fuse with a higher rating can damage the
system and could start a re. Fuse Replacement,
including fuse ratings and locations, is located in the
Maintenance section of this Owner's Manual.
PERSONAL SAFETY
• Remove ignition key and put the vehicle in PARK
or in gear to prevent others from starting the
vehicle during installation or service.
• Wear only snug-tting clothing while working on
your vehicle or spreader.
• Do not wear jewelry or a necktie, and secure long hair.
• Wear safety goggles to protect your eyes from
battery acid, gasoline, dirt, and dust.
• Avoid touching hot surfaces such as the engine,
radiator, hoses, and exhaust pipes.
• Always have a re extinguisher rated BC handy,
for ammable liquids and electrical res.
FIRE AND EXPLOSION
Be careful when using gasoline. Do not use gasoline
to clean parts. Store only in approved containers away
from sources of heat or ame.
CAUTION
DO NOT leave unused material in
hopper. Material can freeze or solidify,
causing unit to not work properly.
Empty and clean after each use.
CAUTION
During the hopper installation we recommend
the addition of an OSHA compliant Backup
Alarm. This alarm is required for OSHA
governed employers.
WARNING
Gasoline is highly ammable and gasoline
vapor is explosive. Never smoke while
working on vehicle. Keep all open ames
away from gasoline tank and lines. Wipe up
any spilled gasoline immediately.
CAUTION
• Do not operate a spreader in need of
maintenance.
• Before operating the spreader, reassemble
any parts or hardware removed for cleaning
or adjusting.
• Before operating the spreader, remove
materials such as cleaning rags, brushes,
and hand tools from the spreader.
• Before operating the spreader, read the
engine owner's manual, if so equipped.
• While operating the spreader, use auxiliary
warning lights, except when prohibited by law.
• Tighten all fasteners according to the
torque chart. Refer to torque chart for the
recommended torque values.

Lit. No. 31022EN, Rev. 00 11 June 1, 2022
SAFETY
CELL PHONES
A driver's rst responsibility is the safe operation of
the vehicle. The most important thing you can do
to prevent a crash is to avoid distractions and pay
attention to the road. Wait until it is safe to operate
mobile communication equipment such as cell
phones, text messaging devices, pagers, or two-way
radios.
VENTILATION
BATTERY SAFETY
NOISE
Airborne noise emission during use is below 70 dB(A)
for the spreader operator.
VIBR ATION
Operating spreader vibration does not exceed 2.5 m/s2
to the hand-arm or 0.5 m/s2to the whole body.
TORQUE CHART
1/4-20 10
91
54
1/4-28 12
11
71
5/16-1
81
50 212
5/16-2
41
70 240
3/8-16 269 376
3/8-24 29
74
20
7/16-1442
96
06
7/16-20
9/16-12
9/16-18
5/8-11
5/8-18
3/4-10
3/4-16
7/8-9
7/8-14 47
46
69
64
49
091-8
1-12 70
49
95
1/2-13
1/2-20
11.9
13.7
24.6
27.3
43.6
26.9
53.3
93
148
49.4
69.8
77.9
106.4
120.0
8.4
9.7
17.4
19.2
30.8
35.0
49.4
55.2
75.3
85.0
M6 x 1.00
M12 x 1.75
M8 x 1.25
M14 x 2.00
M10 x 1.50
M27 x 3.00
M22 x 2.50
M30 x 3.50
M24 x 3.00
M20 x 2.5011.1
19.5
38.5
67
107
7.7
613
778
1139
1545
450
428
562
796
1117
M33 x 3.50
M36 x 4.00
2101
2701
1468
1952
325
M16 x 2.00 231167
M18 x 2.50 318222
Recommended Fastener Torque Chart
Size Size
Torque (ft-lb)
Grade
5
Grade
8
Metric Fasteners Class 8.8 and 10.9
These torque values apply to fasteners
except those noted in the instructions.
Torque (ft-lb)
Grade
5
Grade
8
Size Size
Torque (ft-lb)
Class
8.8
Class
10.9
Torque (ft-lb)
Class
8.8
Class
10.9
Inch Fasteners Grade 5 and Grade 8
CAUTION
Batteries normally produce explosive gases
which can cause personal injury. Therefore,
do not allow ames, sparks, or lit tobacco
to come near the battery. When charging or
working near a battery, always cover your
face and protect your eyes, and also provide
ventilation.
• Batteries contain sulfuric acid, which burns
skin, eyes, and clothing.
• Disconnect the battery before removing or
replacing any electrical components.
CAUTION
Read instructions before assembling.
Fasteners should be nger tight until
instructed to tighten according to the torque
chart. Use standard methods and practices
when attaching spreader, including proper
personal protective safety equipment.
WARNING
Vehicle exhaust contains lethal fumes.
Breathing these fumes, even in low
concentrations, can cause death. Never
operate a vehicle in an enclosed area without
venting exhaust to the outside.

Lit. No. 31022EN, Rev. 00 12 June 1, 2022
LOADING
LOADING
SPREADER SPECIFICATIONS
Hopper
Model
Overall
Length
Bed
Length
Empty
Weight
Overall
Width
Bed
Height
Capacity
Struck
0.35 yd³ 52 in (132 cm) 28 in (71 cm) 192 lb (87 kg) 38 in (97 cm) 24 in (61 cm) 0.35 yd³(0.27 m³)
This Owner's Manual covers vehicles that have been
recommended for carrying the hopper spreader. Please
see your local dealer for proper vehicle applications.
CERTIFICATION
WARNING
Overloading could result in an accident or
damage. Do not exceed GVWR or GAWR as
found on the driver-side cornerpost of vehicle.
WARNING
New untitled vehicle installation of a spreader
requires National Highway Tra󰀩c Safety
Administration altered vehicle certication
labeling. Installer to verify that struck load of
snow or ice control material does not exceed
GVWR or GAWR rating label and complies
with FMVSS.
CAUTION
Read and adhere to manufacturer's
ice-control material package
labeling, including Safety Data
Sheet requirements.
MATERIAL WEIGHTS
Density
Material (lb/ft3)(lb/yd3)(kg/m3)
Salt 80 2160 1282
Sand 100 2700 1602
Material densities are approximate and are based on dry,
loose material. It is the responsibility of the operator to
know the weight of the material to be spread and the vehicle
carrying capacity.
CAUTION
Never use wet materials or materials with
foreign debris with any of these spreaders.
These units are designed to handle dry, clean,
free-owing material.

Lit. No. 31022EN, Rev. 00 13 June 1, 2022
LOADING
DETERMINING VEHICLE PAYLOAD
1. Install the hopper spreader and optional
equipment according to the Installation
Instructions.
2. Install or attach any other equipment that will be
on the vehicle while the hopper spreader will be in
use (step bumper, trailer hitch, snowplows, etc.).
Fill fuel tanks.
3. Obtain the Gross Vehicle Weight Rating (GVWR),
Front Gross Axle Weight Rating (FGAWR), and
Rear Gross Axle Weight Rating (RGAWR) from
the certication label located inside the driver-side
door jamb or door.
4. With the occupants in the vehicle for normal
hopper spreader operation, weigh the vehicle to
obtain gross vehicle weight (GVW).
5. Subtract the GVW from the GVWR to determine
the available material payload.
6. Obtain the weight per cubic yard (lb/yd3) or cubic
meter (kg/m3) of the desired material. Divide the
weight into the payload to determine the maximum
volume of material that can be carried.
7. Refer to the Load Volume table and diagrams to
determine the maximum ll level for the material.
8. Fill the hopper with material to the calculated level.
Reweigh the vehicle with occupants and verify that
the Loaded Gross Vehicle Weight, Front Gross
Axle Weight, and Rear Gross Axle Weight are less
than the vehicle's ratings.
9. Repeat Steps 6–8 for each type of material.
The worksheet for Determining Vehicle Payload (next
page) includes an example.
WARNING
Overloading could result in an accident or
damage. Do not exceed GVWR or GAWR
ratings as found on the driver-side door
cornerpost of the vehicle. See Loading
section to determine maximum volumes of
spreading material.
Hopper
Model
Load Volume (yd3)
ABCD
0.35 yd³
0.4 0.35 0.2 0.03
Load Volume (m3)
ABCD
0.31 0.27 0.15 0.02
LOAD VOLUME
A
B
C
D
A: Rounded Load
B: Struck Load
C: Third Bump
D: Second Bump

Lit. No. 31022EN, Rev. 00 14 June 1, 2022
LOADING
Determining Vehicle Payload Worksheet
Material Type Example:
Dry Salt
AEquipment installed when
vehicle was weighed 0.35 yd3Hopper Spreader
BFront Gross Axle Weight
Rating [FGAWR] 6000 lb (2722 kg)
CRear Gross Axle Weight
Rating [RGAWR] 7000 lb (3175 kg)
DGross Vehicle Weight
Rating [GVWR] 11,000 lb (4990 kg)
EGross Vehicle Weight [GVW],
empty – 7402 (3358 kg)
FPayload Available = 3598 lb (1632 kg)
GMaterial Density ÷ 2160 lb/yd3(1282 kg/m3)
HMaximum Volume = 1.67 yd3(1.27 m3)
I
Loaded Front Gross Axle
Weight (lb/kg) Must be less than
weight in Row B.
A
J
Loaded Rear Gross Axle
Weight (lb/kg) Must be less than
weight in Row C.
K
Loaded Gross Vehicle Weight
[GVW] (lb/kg) Must be less than
weight in Row D.
L
Loaded Gross Vehicle Weight
[GVW] (lb/kg) Must be less than
weight in Row D.

Lit. No. 31022EN, Rev. 00 15 June 1, 2022
UNPACKING THE SPREADER
UNPACKING THE SPREADER
REMOVE SHIPPING BRACKETS AND
LOCATE COMPONENTS
The spreader is shipped from the factory with its
components secured inside the hopper and the top
screen in place. Before installing the spreader, remove the
shipping brackets and top screen, and locate components.
1. Remove the 3/8" anged cap screws and the
top screen brackets, and remove the top screen.
Retain the screen and fasteners for reinstallation.
2. Inside the hopper, remove the eight 3/8" cap
screws from the two shipping brackets that secure
the chute enclosure to the hopper. Set the chute
enclosure aside and discard the shipping brackets
and hardware.
3. Immediately install the provided 3/8" stainless
steel anged cap screws in place of the shipping
bracket fasteners removed from the hopper.
4. Remove the two 5/16" lag bolts that fasten the
spinner deector assembly to the pallet. Remove
the 1/4" hardware that fastens the shipping bracket
to the spinner deector assembly. Set the spinner
deector assembly aside and discard the shipping
bracket and hardware.
CHUTE ASSEMBLY
1. Install four of the provided 3/8" stainless steel
anged cap screws through the spinner guard
holes into the rivnuts on the chute enclosure.
2. Remove and retain the cable boot bracket, dust
cover, and fasteners. Install the left and right side
chute pin ears to the chute enclosure with six
provided 3/8" anged stainless steel cap screws.
Reinstall the cable boot bracket and dust cover.
3. Set chute aside for installation after the spreader has
been installed on the vehicle.
Left-Side
Chute Pin Ear
Spinner Guard
Right-Side
Chute Pin Ear
3/8" Flanged
Cap Screws
Remove brackets.

Lit. No. 31022EN, Rev. 00 16 June 1, 2022
MOUNTING THE SPREADER
3. Using slings or chains, lift the spreader by all four
diagonal corner rails and move it into the vehicle bed.
4. Center the spreader from side to side. Shift the
spreader forward or backward to a position that
will allow the chute, once installed, to overhang
the rear of the vehicle and the bumper. With two
people, trial-t the chute to check for clearance.
INSTALL HOPPER IN VEHICLE BED
NOTE: Periodically throughout the snow and ice
control season, verify that mounting devices
are secure.
1. Remove the vehicle tailgate.
2. Remove the wood shipping rails from the hopper legs.
CAUTION
Before lifting, verify that the hopper is empty
of material. The lifting device must be able to
support the spreader's weight as shown in
the Spreader Specications table.
MOUNTING THE SPREADER
Use all four rails
when lifting.

Lit. No. 31022EN, Rev. 00 17 June 1, 2022
MOUNTING THE SPREADER
5. Use the holes in the two cab-side legs and
two holes in the runner as a template to mark
mounting hole positions on the vehicle bed.
6. Move the spreader temporarily to allow access,
and drill 5/8" holes as marked.
NOTE: Pay special attention when drilling or
clamping dissimilar metals to aluminum bodies.
Galvanic corrosion can occur if not handled
properly. Contact vehicle manufacturer for
recommended attachment practices.
CAUTION
Before drilling holes, check to be sure that no
vehicle wiring or other components could be
damaged.
7. Move the spreader back into position.
Secure the spreader to the vehicle with four
(installer-supplied) 5/8" Grade 5 cap screws as
required by the vehicle application, with 5/8" at
washers on both sides, and 5/8" locknuts.
If the mounting holes are not directly over the
vehicle box supports, the vehicle bed must
be braced to the frame to prevent buckling or
deforming the vehicle bed. Accessory mounting
bars are available for installations that require
additional bracing. Contact your authorized dealer.
8. Remove the cable tie holding the wire harness
to the conveyor chain. Connect the vehicle-side
harness to the hopper-side harness.
9. Reinstall the top screen with the removed cap
screws and brackets.
Mounting Hole
Locations

Lit. No. 31022EN, Rev. 00 18 June 1, 2022
MOUNTING THE SPREADER
Construct Sill Spacer
Measure the distance from the front end of the hopper
sill to the front of the vehicle bed and make a spacer
from 2" x 8" lumber to t that area.
Failure to install a spacer could result in damage
to the spreader.
Install Tie-Down Straps
NOTE: Periodically throughout the snow and ice
control season, verify that mounting devices
are secure.
Install tie-down straps from the tie-down loops on the
spreader body to the vehicle frame as shown. Use
one strap per loop, pulling diagonally away from the
hopper body.
WARNING
Spreader shall be bolted to vehicle frame.
Do not rely on the tie-down chains or straps
alone to hold spreader in vehicle.
Ratchet
Strap
Assembly
15°
Minimum
Vehicle
Tie Down
or Eyebolt Fit to vehicle.
Measured
distance.
18"
(46 cm)
Front of
Vehicle Bed
Measure distance.
Trough
End Cap
Spacer
Built to Fit

Lit. No. 31022EN, Rev. 00 19 June 1, 2022
SPINNER DRIVE ASSEMBLY
SPINNER DRIVE ASSEMBLY
INSTALL SPINNER DRIVE ASSEMBLY
NOTE: Complete the assembly installation in the
Chute Assembly section before proceeding with
these instructions.
1. Carefully set the spinner drive assembly on the
ground. Orient it in operating position as shown
below.
2. Attach the spinner drive assembly to the spreader
with the lock pins from the parts box. Install the
upper lock pin rst.
The upper lock pin goes through the lower chute
support holes and the upper chute pin ear holes.
The lower lock pin goes through the lower chute
pin ear holes and the chute support.
Secure each lock pin with a cotter pin.
3. Connect the spinner motor harness to the female
connector extending from the rear of the hopper.
Cotter
Pins
Lock
Pins
Chute
Supports
Female Connector
Spinner Drive Assembly

Lit. No. 31022EN, Rev. 00 20 June 1, 2022
OPERATING THE SPREADER – CAB CONTROL
OPERATING THE SPREADER – CAB CONTROL
POWERING THE CONTROL
Power is not applied to the control until the vehicle
ignition is turned to ACC or ON. Once the control
has power it performs a light check and displays the
software version on the status display. The control
then checks for a connected spreader. If no spreader
is detected, the control does the following:
• nC (no connection) appears on the red status
display for ve seconds;
• A single beep;
• Control enters Standby mode with no lights
illuminated.
If any button is pressed on the control, it will wake and
check again for spreader connection. If no spreader is
detected, it will act as described above. If a spreader
is detected, it will transition to Ready mode.
Material
Width
Material
Flow
VIBRATELIGHT STROBE PREWET
MINMAX
ON/OFF
MI
NM
AX
BLAST
Material Width
Control Knob
(spinner speed)
Indicator Lights
(8 per knob)
Material Flow
Control Knob
(feed rate)
BLAST Button
(maximum application)
ON/OFF Button
& Emergency Stop
Status/Error Code
Display (red)
Accessory
Control Buttons
WARNING
Never operate equipment when under the
inuence of alcohol, drugs, or medications that
might alter your judgment and/or reaction time.
WARNING
Never exceed 45 mph (72 km/h) when loaded
spreader is attached to vehicle. Braking
distances may be increased and handling
characteristics may be impaired at speeds
above 45 mph (72 km/h).
WARNING
Never allow children to operate or climb on
equipment.