Sodex Sport S16233 Dimensions

DESCRIPTION
Galvanised teel structure 80x80
Powder coated
3,00m x 2,00m
CONFORM
European standard
NF EN 749
PRODUCT SHEET
HANDBALL MOBILE GOAL FOR
COMPETITION
PRODUCT REF :S16233 PAIR
ASSEMBLY TIME
The necessary time to assemble this product is estimated at 30 minutes with 2 persons (without concreting).
TEST AFTER INSTALLATION
According to the regulation above, this product has to be tested like below:
- Put 180kg at 20cm from the ground and in the middle of the crossbar during 1min.
- Apply an horizontal force of 110 kg on the middle of the crossbar, thanks to a 3 meters rope, during 1min.
After these tests, the equipment and the fixation system should not have break, move or show residual
deformation.
During the first installation, stability and strength tests are compulsory.
Every time you install the equipment, a visual check of the stability and strength must be realized.
The owner of this equipment must usually control the product.
For an optimal use of our products, we advise to follow the installation and maintenance instructions.
MAINTENANCE
The equipment has to be regularly maintained by the owner. It is recommended to:
- Check every week that all the bolts are correctly tightened.
- Fix paint defects if the unit has been damaged, using the adapted paint specified by the manufacturer.
- Replace all damaged or missing parts with a spare part recommended by the manufacturer.
- Clean the product by using dishwasher soap, clean water, and soft cloth.
WARRANTY
One full year parts and labour guarantee. Every claim regarding the condition of the delivered equipment has to be
done within the warranty period following receipt of the product.
The warranty will not apply to:
- Any degradation during transport.
- Any degradation due to poor maintenance.
- Any degradation due to use differing from which the product was intended.
- Any defect claimed after the end of the warranty period.
- Any damage due to a faulty installation or assembly of the product.

2
NB: All dimensions are written in millimeters
NECESSARY TOOLS (NOT INCLUDED)
Driller Concrete drill D16mm
Mallet
Main frame
80x80
FIXATION AND FOOTING
Rear footing
250x250x250mm
Variable
dimension
Concrete block
250
250
250
- Dig the holes for the footing of the anchors
according to the written dimensions.
- Realize the footing with concrete CPJ45
dosed by 350 kg and wait at least 72 hours
(6 days during winter).
- Once the concrete is in the hole, put the
anchor’s tubes.
- Drill the holes for the chemicals fixings by
using a concrete drill diameter 16 mm. Do not
drill a hole more than 80mm.
Rear footing
250x250x250mm

3
ASSEMBLY
NECESSARY TOOLS (NOT INCLUDED)
INCLUDED ITEMS
Wrench 17mm
x8
Lifting ring
M12x40
x8
Chemical fixing
M12x50
x4
Anchors
SS Screws
M10x30
x24 x32
SS Washers 10
x8
SS Screws
M10x70
NECESSARY
ITEMS
1– ASSEMBLY OF THE ARCHES TO THE FRAME (x4)
STEP 2STEP 1
POST
SS Screws M10x30
+ SS Washers 10
SS Screws M10x30
+ SS Washers 10
POST
SS Screws
M10x30
x6 x6
SS Washers 10
RUBBER SUPPORTS

4
ASSEMBLY
2– ASSEMBLY OF THE LOWER CONNECTION BAR (x4)
NECESSARY
ITEMS
CONNECTION BAR
ARCH
x1
SS Washer 10
x1
SS Screws
M10x70
SS Screw M10x70
+ SS Washer 10
RUBBER
SUPPORTS
RUBBER SUPPORTS
3– ASSEMBLY OF THE UPPER CONNECTION BAR (x4)
NECESSARY
ITEMS
CONNECTION BAR
ARCH
x1
SS Washer 10
x1
SS Screws
M10x70
SS Screw M10x70
+ SS Washer 10

5
ASSEMBLY
4– FIXATION OF THE GOAL (x4)
NECESSARY
ITEMS
Lifting ring
M12x40
Chemical fixing
M12x50
Anchor
x2
Lifting ring
M12x40
x2
Chemical fixing
M12x50
x1
Anchors
CONNECTION BAR

NOMENCLATURE
Package
N° Ref Index Designation Description Quantity Packing method Weight (kg)
Dim.
(mm)
A1 S16231-01 EFront frame 1
Plastic bubbles
+ cardboard 5
layers
40 3200x2100x100
A2 S16231-01 EFront frame 1
Plastic bubbles
+ cardboard 5
layers
40 3200x2100x100
A3 S16326-03 CR&L arch 2
Plastic bubbles
+ cardboard 2
layers
29 2100x1240x220
A4 S16326-03 CR&L arch 2
Plastic bubbles
+ cardboard 2
layers
29 2100x1240x220
A5 S16326-05 AConnection bars 2
Plastic bubbles
+ cardboard 2
layers
19 3080x130x130
A6 S16326-05 AConnection bars 2
Plastic bubbles
+ cardboard 2
layers
19 3080x130x130
A7 S16233-09 AAccessories 1Cardboard 5
layers 2350x160x100
ACCESSORIES PUT IN CLEAR PVC BAG
Package
N° Ref Designation Description Qty Note
A7 BITH1030 +
LITA102220 +
SS Screws M10x30 +
SS washers 10 24 + 24 Assembly of arches to front frame
A7 BITH1070 +
LITA102220
SS Screws M10x70 +
SS washers 10
8 + 8 Fixation of joining bar
A7 TKD1250 +
S16340EZ
Chemical anchors M12x50
+ lifting rings M12x40 8 + 8 Goal anchoring
A7 S16328EZW-01 Anchors 50x50 4Goal anchoring
PACKING LIST
HANDBALL MOBILE GOAL FOR
COMPETITION
PRODUCT REF S16233 Index A PAIR

PRE-ASSEMBLED ACCESSORIES
Package
N° Ref Designation Description Qty Note
A1 +
A2 S12361+ RV4016 Plastic hook 2 fixations +
Rivets D4 42 + 84 Fixed on front frame
A3 +
A4 S12363 + VITF4819 1 fixation hooks + self- tapping screws M4.8x19 12 + 12 Fixation to arch
A1 +
A2 NNV80 PVC cap 80 4Fixed on posts
A3-A6 TC05 Rubber supports
100x50x5mm 12
A1 +
A2 BITH1040 SS Screws M10x40 4Fixation stabilizer bar
A1 +
A2 Conformity stickers 2
A1 +
A2 Stabilizer bar 2To maintain the goal during transportation
VISA PACKING DEPARTMENT DATE :
PACKING LIST
HANDBALL MOBILE GOAL FOR
COMPETITION
PRODUCT REF S16233 Index A PAIR