Solaro Energy SolaroAire BVS-30W User manual

• Drill
• Measuring Tape
• Pencil
• Utility Knife
• Safety Goggles
• Caulk/Caulking Gun
• Wire Cutter
• Wire Strippers
Tools Needed:
The Basement Ventilation System is fully functional right out of
the box. THE FAN WILL BEGIN TO OPERATE ONCE THE PANEL IS
CONNECTED TO THE BASEMENT SYSTEM. PLEASE KEEP HANDS
AND TOOLS AWAY FROM THE BLADE DURING THE INSTALLATION.
Important Precautions:
• When determining the location of the solar panel, try to face the
panel towards the equator (South in the Northern Hemisphere or
North in the Southern Hemisphere).
• Avoid potential problems such as shading from large objects,
large trees, or other houses which may cause shading during
certain times of the day.
•WARNING: Avoid all contact with the blades. Even a small
bend in the blades can cause severe vibration & premature motor
failure.
• Do not cut any structural members in the house
• Always measure twice and cut once.
• Installation of the Basement System should be located in the
basement of the building.
• Take precaution while installing the panel on the roof
Components & Parts List:
Helpful Hints:
Basement Ventilation Unit
Solar Panel Exhaust Ports Power Supply
Material Included with Kit
Model Numbers:
BVS-30W
BVS-40W
BVS-50W
A.
B. C. D
E.
Basement System Install Pack
•F-030: (4) 1.5” Dual thread rubber washer screw
• A-BRT4: (4) Solar Feet
• F-016: (12) 1.25” self tapping philips truss head screws
• F-018: (36) .5” self drilling philips truss head screw
(20 Black, 16 white)
• E-CNR: (4) Wago Connectors
F-030 A-BRT4 F-016 F-018
50ft. Cable
Pre-attached
Aluminum Tape
Drywall Anchor Screw #25310 Wall Anchor
Rubber Grommet
Template
2 - 6” Flexible Duct
E-CNR
WARNING: Take caution during installation. Please
read through ENTIRE packet before performing
any work. Not following the instructions can void
the warranty and/or cause serious injury. For
professional help, please call 1-888-355-5SUN
Each duct is 10 ft. long
(12) (12) (8)

Installation:
Please allow up to an hour for installation. Components and hardware are referenced in each step to the corresponding letters on
the parts list. (See components and parts list).
NOTE: Most rafters are spaced between 16” (41cm) to 24”(60.96cm) on center. Best performance will be achieved by
placing the basement ventilation system in the basement. Its ideal to place it close to the wall so the exhaust ports easily
attach to the system. For either placement DO NOT CUT INTO THE RAFTERS or any other structural member of the building.
Step 1: Mount lower base plate
• Measure 1-3 inches off the ground (Fig. 1.1)
• At 1”above ground assembled unit will sit on ground
• Align bottom of baseplate with the mark on the wall
- If screwing into stud, use the supplied fasteners and attach to
wall
- If screwing into drywall, mark the 6 screw holes on the wall.
• Remove baseplate and drill holes over the marked spots
• Insert anchors
• use supplied fasteners to attach unit to wall (Fig. 1.2)
1.1
1.2

3.1
3.2
Step 3: Drill Holes for exhaust ducts
• Place guide plate in the center of the desired exhaust location
(Fig. 3.1)
• Drill pilot holes
• Using the 6” hole saw to drill the holes using the pilot holes just
cut.
• Drill 1/4” hole under the 6” hole to route the solar panel wire
through
• Mount exhaust vents
• Attach flex duct to exhaust vents using silver aluminum tape
(Fig. 3.2)
Step 2: Mount upper baseplate
•Align upper and lower baseplate
• Follow steps of steps 4
2

Step 1: Positioning solar panel feet on solar panel
• Place a mark (using a pencil or sharpie) 4” (101.6 mm) from edge at
all four corners. (Fig. 1.1)
• Gripper pad on the bracket (A-BRT4) will be pointed away from
back of the panel. (Fig. 1.2)
• Drill the brackets in place with the #8 1 ½” (38.1 mm) (F-018) self
drilling phillips head screw. (Fig. 1.3)
• Repeat for all four brackets (A-BRT4). (Fig. 1.4)
Note: Do not use the Prepunch holes in the solar panel
along the long edge of the solar panel. to attach solar panel
feet to panel.
1.1 1.2
1.3 1.4
Install solar panel on shingle roof
Step 2: Locating the Solar Panel on the roof
•Pick a location for the panel that maximizes the sun hitting it when
the light is wanted the most. Typically this means a South facing
roof in the Northern hemisphere.
• Roughly locate center of where panel will mount for cable
penetration. Make sure not to hit framing underneath. (Fig. 2.1)
• Drill one ½” (12.7 mm) hole through the sheathing. (Fig. 2.2)
2.1
2.2
Step 3: Mounting the Solar Panel
• Position the solar panel centered over the roof grommet.
•Using a sharpie, mark the four holes of the brackets.
•Add caulking to the four markings and reposition the panel
back into place. (Fig 3.1)
• Fasten solar panel with rubber washer head screws
(F-030) through each mounting bracket. (Fig 3.2 & 3.3)
3.1
3.2
3.3

4
Step 4: Run the wire down the house or building
• Use staples or anchors to secure the cable that is wired from
the solar panel to the fan housing in the crawl space
Step 6: Attach lower face plate
• Align holes (Fig. 6.1)
• Attach DC Power supply to matching connector
• Use wire guides to secure cable to inside of unit
• Screw power supply strain relief into housing
• Align holes
• Using supplied screw attach lower faceplate to lower baseplate
• Using supplied sealant, caulk around where the lower faceplate meets
the plate with two six inch vents
6.1
6.2

Step 7: Wire Assembly
• Using wago attach solar panel ground wire to the motor
• Following tags on switch, use wagos to attach motor positive, panel
positive, and dc power positive to switch
Step 8: Attach upper faceplate
• Align holes (Fig. 8.1)
• Use supplied fasteners to attach faceplate
Step 9: Attach the name plate
• Align holes
• Use supplied fasteners to attach faceplate
8.1
7

Solar Panel
25ft. Cable
Exiting Air
Circulating Air
Incoming air from outside or
other parts of the home
How it works:

Each Solaro Aire™ system is carefully built to exact specifications and packaged with great care. We expect your
purchase to be one that will last you a lifetime and we will make every effort to ensure your satisfaction.
The Solaro Aire™ cannot be altered in any way by the end user. The warranty is extended to the original purchaser,
whose name appears on the warranty certificate and is in effect at the location shown on the warranty certificate. This
warranty applies to residential or commercial installations and is non-transferable.
The word “defect (s)” as used in this warranty, is defined as imperfections that impair the functionality of the Solaro
Aire™ system (s). Implied warranty of merchantability and fitness for a particular purpose are limited to the terms of
this warranty. Solaro Energy Inc. provides a Limited Lifetime Warranty on all parts and mechanisms on all of its Solaro
Aire™ system (s) and to be free of defects in material and workmanship.
This Limited Lifetime Warranty does not cover damage caused by misuse, abuse, scratching, corrosive atmosphere
contaminants, lightning, earthquakes, windstorms, tornadoes, flooding, fire, modification, vandalism, negligence, or
other causes beyond our control. This includes, any other act of God.
In no event shall Solaro Energy Inc. be liable for direct or indirect loss, consequential damage, or any other claims
except as provided for in this warranty. Defective components will be replaced free of charge for up to 10 years from
the date of installation. After 10 years of service (5 years when using 40 watt or 50 watt solar panel) brushless motor
replacement may be subject to shipping and handling charges. The warranty will not cover the cost of labor, applicable
taxes, shipping, or other consequential expenses related to the removal, return, or re-installation. See local
dealer/distributor for applicable charges.
On the date of your purchase of the Solaro Aire™ Basement System fan, please complete and return the
bottom section on this Limited Lifetime Warranty certicate. Keep the top portion for your recored