Solena MINI-PAR-3 User manual

User's Manual
MINI-PAR-3
3*8W RGBW 4-in-1 LED PAR LIGHT
ATTENTION: Read this manual before using. Do not attempt to open the
housing or repair this device by yourself without contact us!

* Under [CH]，press ENTER into DMX512 channel setting.
* Press UP/DOWN to select channel CH06 or CH24，press ENTER to save the selection. Press
MENU to the previous setting.
(8) Sound sensitivity setting
*Under [SEnS], press ENTER into Sound sensitivity setting
*Press UP/DOWN to increase/decrease sensitivity value 001—100, press ENTER to save the
setting. Value increase, sensitivity higher
Troubleshooting
1. If the power supply indicator doesn't light up and the light doesn't work, please check the
power supply, the input voltage and the fuse.
2. In Stand-Alone operation, if the power supply indicator is light up and sound active indicator
isn't light up, but the light is shut off doesn't work.
A. Because sound is too small make for light shut off in sound active, please increase the music
volume or increase audio sensitivity with sensitivity knob, please check as below.
B. Please check if unit has been set up in slave mode, then set up in master mode.
3. In Master-Slave operation, slave unit don't function, please check as below.
A. Make sure to there's only one master in the chain, and the others are set in slave mode.
B. Make sure to control the unit without DMX console controlling.
C. Make sure to take a good quality power cable and connection.
Warranty Warnings:
1. Damages caused by the disregard of this user manual are not subject to Warranty.
The dealer will not accept liability for any resulting defects or problems.
2. Please consider that unauthorized modifications on the device are forbidden due to safety
reasons. Please note that damages caused by manual modifications on the device or
unauthorized operation by unqualified persons are not subject to warranty.
3. If this device will be operated in any way different to the one described in this manual, it may
suffer damages and the guarantee becomes void. Furthermore, any other operation may lead to
dangers like short-circuit, burns electric shock, etc.
After trying the above solution you still have a problem, please contact your dealer or our
company for service.
Page 12
General Instructions
Unpacking:
Thank you for purchasing this product. Please read user guide for safety and operations
information before using the product. Keep this manual for future reference. This product can
create perfect light programs and effects since it has passed a series of strictly tests before
delivery. Please check the attachments listed on the page after opening the carton.
Immediately upon receiving a fixture, carefully unpack the box. Check the box contents to
ensure that all parts are present and that they are in good condition. If any part appears
damaged from shipping, or if the box shows signs of mishandling, notify the shipper
immediately. In addition, retain the box and all the packing material for inspection. In any
event, save the carton and all packing material because, in case that you have to return the
fixture to the factory, you will have to do so in its original box, with its original packing.
What is included: 1* Light, 1*Power Cable, 1*User Guide
Safety Notice:
Please read the following notes carefully because they include important safety information
about the installation, usage and maintenance of this product. It is important to read all these
notes before starting to work with this product.
There are no user serviceable parts inside the light. Any reference to
servicing this unit you may find from now on in this User Manual will only
apply to properly C we certified technicians. Do not open the housing or
attempt any repairs unless you are one of them.
Please refer to all applicable local codes and regulations for proper
installation of the light.
Keep this manual for future consultation. If you sell the light to
another user, make sure that they also receive this manual.
Avoid direct eye exposure to the light source while the fixture is on. Always
disconnect the light from its power source before servicing. Always connect the
light to a grounded circuit to avoid the risk of electrocution.
Page 1

This product is for indoor use only! Use only in dry locations. Keep this
device away from rain and moisture, excessive heat, humidity and dust. Do
not allow contact with water or any other fluids, or metallic objects.
Make sure there are no flammable materials close to the fixture(s)
while operating.
Please prevent this light away from electrical shock
When hanging this fixture, always secure it to a fastening device
using a safety cable (not provided).
Always make sure that you are connecting the light to the proper voltage, as
per the specifications in this manual or on the product's sticker. Never
connect the light to a dimmer pack. Make sure that the power cable is not
cracked, crimped or damaged. Never disconnect the fixture by pulling or
tugging on the power cable.
The maximum ambient temperature (Ta) is 104 F (40 C). Do not
operate the fixture at a higher temperature. In case of a serious
operating problem, stop using this product immediately!
Use cleaning tissue to remove the dust absorbed on the external
lenses periodically to optimize light output.
Always replace with the exact same type fuse, replacement with
anything other than the specified fuse can cause fire or electric
shock and damage your unit, and will void your manufactures
warranty.
Do not remove or break the warranty label, otherwise it void the
warranty.
There are no serviceable parts in the LED light. Please have all
servicing and adjustments made by a qualified service engineer.
Don’t throw this product away just as general trash, please dispose of this
product following the abandon electronic product regulation in your country.
To protect the environment, recycle packing material wherever
possible.
Page 2
(4) SOUND mode Setting
Soud
Sod1
Sod3
* Under [Soud]，press ENTER into SOUND running mode
* Press UP/DOWN to select (Sod1---Sod3) 3 kinds of Sound running modes. Press ENTER to save
the selection. Press MENU to the previos selection.
* Digital display function details:
Sod1
Includes Sod2---Sod3 All SOUND running effects. 1 minute each time
Sod2
R-G-B-W SOUND jumping
Sod3
R-BW-G-RW-B-GW-RGB-W-RB-GBW-RG-RBW-GB-RGW-RGBW 15colors SOUND jumping
Sod4
R-BW-G-RW-B-GW-RGB-W-RB-GBW-RG-RBW-GB-RGW-RGBW
15colors Sound color change strobe
Sod5
RGBW ALL LED sound strobe
(5) DMX mode Setting
d001-d512
d001-d512
* Under [dxxx]，(xxx:001--512）press ENTER into DMX512 setting mode
* Under DMX512 setting mode, press UP/DOWN to increase or decrease the address 001---512,
then press ENTER to save the setting. Press MENU to the previous setting.
* Once DMX512 signal can be received normally, it will display d.xxx (xxx: means DMX address)
(6) Master/Slave mode Setting
SLAu
* Under [SLAu]，press ENTER into Slave mode. Once Master unit links with Slave unit in good
condition, LCD displays SLAu.
(7) DMX Channel Setting
Ch
CH05
CH08
Page 11

*Press S00-S16 to set strobe speed. Value to 00, no strobe; value 01-16, strobe speed is 1HZ-16HZ.
(2) Static color Setting
CC01-CC15
CoLo
* On the MENU [CoLo], press ENTER for color setting
* Press UP/DOWN, value 01-15, it has 14 kinds of static color selections. Press ENTER to save the
setting, press MENU to the previous setting.
(3) AUTO mode Setting
AuTo
AuLL
Au.01
Au.06
S 01-----S 16
* Under [AuTo], press ENTER into AUTO mode
* Press UP/DOWN to select AuLL A01.XX---A06.XX（XX:01--06) 7 kinds of AUTO mode. Press
ENTER into AUTO running speed S01-S16 setting. Press MENU to the main manu.
*On the running speed setting, press UP/DOWN to set 15 kinds of speed level 01—16. Increase value
for fast speed. Press ENTER to save the speed level. Press MENU to AUTO running speed mode.
AuLL
AUTO running Au.01XX---Au.06 all effects, change 30 seconds/time
Au.01
R-G-B-W 4 color AUTO jumping, speed from 01--S16
Au.02
R-BW-G-RW-B-GW-RGB-W-RB-GBW-RG-RBW-GB-RGW
-RGBW 15 color AUTO jumping, speed from 01--S16
Au.03
RonGup--RdownGon--GonBup--GdownBon--RupBon—RonBdown
7 colors dimming, speed from 01--S16
Au.04
RonGup--RdownGon--GonWup--GdownWon--BupWon--BonWdown--
GupBon--GonBdown--RupGonWup--RonGdownWon--RdownWon--
GupBupWon--GdownBonWdown--RupBon--RonBdown--RonGupBup--
RdownGonBon--GonBonWup--GonBdownWon--RupGonWon--
RonGonWdown--RonGonBup--RonGdownBon--RonBonWup—
RonBdownWon—RonWdown Color AUTO dimming, speed from
01--S16
Au.05
R-BW-G-RW-B-GW-RGB-W-RB-GBW-RG-RBW-GB-RGW-RGBW
AUTO change, AUTO strobe, AUTO color change speed 10S, strobe
speed from S01-S16
Au.06
RGBW all on and strobe, speed from S01-S16
Page 10
LED Expected Lifespan
LEDs gradually decline in brightness over time. HEAT is the dominant factor that leads to
the acceleration of this decline. Packaged in clusters, LEDs exhibit higher operating
temperatures than in ideal or singular optimum conditions. For this reason when all color
LEDs are used at their fullest intensity, life of the LEDs is significantly reduced. It is
estimated that a viable lifespan of 40,000 to 50,000 hours will be achieved under normal
operational conditions. If improving on this lifespan expectancy is of a higher priority,
place care in providing for lower operational temperatures. This may include
climatic-environmental and the reduction of overall projection intensity.
Technical Specification
(1)Super bright LED light
(2) long life span upto 20000 hours
(3) Many functions can be achieved through DMX control, such as color change, speed
control, strobe, LED brightness, dimmer, etc.
*LED source: 3*8W RGBW LEDs, total power 24W
*Dimming: electronic dimmer 0% 100%
*Beam angle: 25 degrees
*Operation mode: Sound Active, AUTO, DMX, Master/Slave
*DMX channel: 5CH and/or 8CH
*4 digital display
*Interface: 3 pins XLR jack for DMX or Maser-Slave linking
*Voltage: AC90-240V, frequency: 50HZ to 60HZ, 2A
*Power Rate: 12W
*Net Weight: 0.3Kg
*Gross Weight:0.5Kg (inner box)
*inner: 153*137*115(0.0024cbm)
*Outer Box: 568*326*365 (0.068cbm), 24pcs/CTN
Page 3

Fixture Appearance
1. LED bulbs, 2. hanging handle, 3. LCD Digital display
4. key menu: menu, enter, up, down,5. DMX linking XLR IN/OUT,
6.Power source
Function & Setting
Sound Active
The change of the LED pattern is controlled by sound, that is, the rhythm of the sound control
the effect of the changing light pattern.
Page 4
Soud
Sod1
Sod5
d001-d512
d001-d512
SLAu
Ch
CH05
CH08
SEnS
001----100
LCD Digital Operation Details
(1) Color brightness adjustment
b000-b255
rgbu
r000-r255
g000-g255
r000-r255
g000-g255
b000-b255
S 00-S 16
u000-g255
u000-g255
* On the MENU [rgbu], press ENTER to set color selection
*Press UP/DOWN, then press ENTER to set color brightness adjustment. Press MENU to the
previous setting
* Press UP/DOWN for the increase/decrease value 0-255, press ENTER to save the value. Press
MENU to the previous setting.
Page 9
1
2
6
5
3
4

LCD Digital Display
MENU: Function mode selection, such as DMX512/Masterslave, AUTO strobe, Sound Active
Strobe, Constant light on, brightness adjustment
DOWN/UP: previous or next, increase or decrease
Enter: confirm and save the selection
LCD Digital Display Chart
b000-b255
rgbu
r000-r255
r000-r255
g000-g255
b000-b255
u000-u255
u000-u255
S 00-S 16
S 00 -S 16
CC01-CC15
CoLo
AuTo
AuLL
Au.01
Au.06
S 01 ---S 16
Page 8
AUTO
Auto cycles the built-in programs without being controlled externally. It has no light OFF.
Stand-Alone Operation (Sound Active, AUTO mode)
The mode allows a single unit to react to the beat of the music in the master mode.
1. Install the units in a suitable position (laying or appending).
2. Set dipswitch to select Sound Active or AUTO mode.
3. Turn on the unit power, the unit begins reset, then the unit begins working.
4. The unit will react to the low frequencies of music via the internal microphone. Adjust the audio
sensitivity knob on the back of the unit to make the unit more or less sensitive in sound active. The
panel has LED indicating for sound active.
Master-Slave Operation
This mode will allow you to link up to 32 units together without controller.
1. Install the units in a suitable position (laying or appending).
2. Choose a unit to function as Master mode, set dipswitch to select Sound Active or AUTO mode.
The others must be set to Slave mode, set dipswitch to select Slave mode.
3. Use standard XLR microphone cable chain your units together via the XLR connector on the rear
of the units. For longer cable runs we suggest a terminator at the last fixture.
Caution: Do not allow contact between the common and the fixture’s chassis ground. Grounding the
common can cause a ground loop, and your fixture may perform erratically. Test cables with an ohm
meter to verify correct polarity and to make sure the pins are not grounded or shorted to the shield or
each other.
4. Turn on the all units' power, the units begins reset, and then the unit begins working. The slave
units will re-act the same as the master unit.
5. The units will react to the low frequencies of music via the internal microphone. Adjust the audio
sensitivity knob on the back of the master unit to make the unit more or less sensitive in sound active.
The panel has LED indicating for sound active.
Page 5

Universal DMX Operation (DMX mode)
The system only accepts the DMX512 signal of international standard to control the
system. This mode allows you to use universal DMX-512 console to operate.
1. Install the units in a suitable position (laying or appending).
2. Use standard XLR microphone cable chain your units together via the XLR connector on
the rear of the units. For longer cable runs we suggest a terminator at the last fixture.
3. Assign a DMX address to each the unit using dipswitches, see the "DMX Address Quick
Reference Char".
4. Turn on the all units' power, the units begins reset, and then the unit begins working.
5. Use DMX console to control your units.
DMX Control:
The LED light only accepts the DMX512 signal of international standard to control the light.
DMX Control Parameter Chart
(1) 5 channels
Channel
Function
Value
Description
CH1
Red brightness
0-255
Dark to bright
CH2
Green brightness
0-255
Dark to bright
CH3
Blue brightness
0-255
Dark to bright
CH4
White brightness
0-255
Dark to bright
CH5
Strobe/Flashing
0-63
No strobe
64-223
AUTO strobe, speed from slow to fast
224-255
Sound strobe
(2) 8 channels
Channel
Function
Value
Description
CH1
All LEDs
brightness
0-255
Dark to bright
CH2
Red brightness
0-255
Dark to bright
CH3
Green brightness
0-255
Dark to bright
CH4
Blue brightness
0-255
Dark to bright
CH5
White brightness
0-255
Dark to bright
Page 6
Channel
Function
Value
Description
CH6
Color change
0-31
Color controlled by CH1 to CH5, no all color change
32-95
Static color selection CC01—CC16 with 15 colors
controlled by CH7
96-143
Color change RonGup –RdownGon –GonBup—
GdownBon --RupBon-- RonBdown
144-191
RonGup--RdownGon--GonWup--GdownWon--
BupWon--BonWdown--GupBon--GonBdown--
RupGonWup--RonGdownWon--RdownWon--
GupBupWon--GdownBonWdown--RupBon--
RonBdown--RonGupBup--RdownGonBon--
GonBonWup--GonBdownWon--RupGonWon--
RonGonWdown--RonGonBup--RonGdownBon--
RonBonWup--RonBdownWon—RonWdown, color
AUTO dimming, speed controlled by CH7
192-223
R-BW-G-RW-B-GW-RGB-W-RB-GBW-RG-RBW-
GB-RGW-RGBW Color AUTO jumping, speed
controlled by CH7
224-255
R-BW-G-RW-B-GW-RGB-W-RB-GBW-RG-RBW-
GB-RGW-RGBW Color Sound jumping
CH7
Static color
selection and
speed control
0-255
CC01---CC16 15 kinds of static colors, speed from
slow to fast
CH8
Strobe/Flashin
g
0-63
No strobe
64-223
AUTO strobe, speed from slow to fast
224-255
Sound strobe
Notes:
(1) Power on the light, LCD displays d001, connect XRL DMX cable, power on DMX controller,
then the light will receive the DMX signal if the light and DMX Controller are connected.
(2) Under the d001, several lights are linked. If there is no DMX controlled connected, Master/slave
can be set stand alone. One light is Master and other lights are Slave.
Page 7