Solent RemoteF5 User manual

To fan/NEUTRAL
BLACKR ED
NL AC Power Input
L
N
BLACK
To fan/LIVE WHITE
Connection Block
on Fan Motor
Receiver
Antenna
WIRING DIAGRAM
t+27 (0) 31 563 4600 | [email protected] | www.solent.co.za
Transmitter Functions
Fan Off
1. Fan On - Slow
2. Fan On - Low
3. Fan On - Medium
4. Fan On - Medium High
5. Fan On - High
Transmitter & Receiver Pairing
1. Within 30 seconds from the power being
switched on, press the FAN OFF button until
the fan starts rotating.
2. Pairing is now complete.
Timer Function
1. There are 5 Timers – 1 hour, 2 hours,
4 hours, 6 hours and 8 hours.
2. The Timer must be set while the fan is in
rotation and it can be set on any speed.
3. Press the desired Timer to put the fan in
sleep mode and the fan will turn off when
the selected Timer is reached.
Receiver Connection
1. Connect the RECEIVER as shown in
wiring diagram.
Receiver Placement
1. Once the connection is made, place the
RECEIVER in the canopy, slide the canopy
up and tighten in position.
Receiver Memory Function
1. After a power outage or a tripped circuit
breaker, the fan will default to
Fan ON.
The fan will run at the speed
that was last saved in memory.
RemoteF5
RemoteF5 - Fan Five Speed only
IMPORTANT POINTS
1. Caution: Do not use this product in
conjunction with any wall/speed
regulator.
2. Please note that all fixed wiring
appliances should be installed by a
qualified electrician.
3. The supply to the remote control
receiver should be connected
through a mains switch, i.e. existing
wall switch.
4. Disconnect from power supply at
wall switch before working on remote
control receiver or ceiling fan.
5. This unit is to be used for the control
of ceiling fans and in an AC230/240V
50Hz power supply only.
6. The remote receiver must be used
within its load rating of 100 watt
maximum.
7. Do not install in damp locations or
immerse into water. (For indoor use
only.)
8. The batteries will weaken with age
and should be replaced before
leaking takes place as this will
damage the transmitter.
Overload Protection for Fan Motor
If your fan or light suddenly goes off, check
the protection fuses.
Installation of
TransmitterWall Mount
Holderwith two screws
Fan Off
Indicator
Light
Fan Timers
1 to 8 hours
Fan On - Slow
Fan On - Low
Fan On - Medium
Fan On - Medium High
Fan On - High
TRANSMITTER
RECEIVER PLACEMENT
RECEIVER CONNECTION
AC Power Supply
BLACK
(Mains/Neutral)
RED
(Mains/Live)
Antenna
BLACK
WHITE
(Fan/Live)

WIRING DIAGRAM
t+27 (0) 31 563 4600 | [email protected] | www.solent.co.za
Transmitter Functions
Fan Off
1. Fan On - Slow
2. Fan On - Low
3. Fan On - Medium
4. Fan On - Medium High
5. Fan On - High
Light On/Off
Transmitter & Receiver Pairing
1. Within 30 seconds from the power being
switched on, press the FAN OFF button until
the light on the fan flashes once and the
fan starts rotating.
2. Pairing is now complete.
Timer Function
1. There are 5 Timers – 1 hour, 2 hours,
4 hours, 6 hours and 8 hours.
2. The Timer must be set while the fan is in
rotation and it can be set on any speed.
3. Press the desired Timer to put the fan in
sleep mode and the fan will turn off when
the selected Timer is reached.
Receiver Connection
1. Connect the RECEIVER as shown in
wiring diagram.
Receiver Placement
1. Once the connection is made, place the
RECEIVER in the canopy, slide the canopy
up and tighten in position.
Receiver Memory Function
1. After a power outage or a tripped circuit
breaker, the fan will default to
Light OFF and Fan ON.
The fan will run at the speed
that was last saved in memory.
RemoteL5
RemoteL5 - Fan Five Speed with Light On/Off
IMPORTANT POINTS
1. Caution: Do not use this product in
conjunction with any wall/speed
regulator.
2. Please note that all fixed wiring
appliances should be installed by a
qualified electrician.
3. The supply to the remote control
receiver should be connected
through a mains switch, i.e. existing
wall switch.
4. Disconnect from power supply at
wall switch before working on remote
control receiver or ceiling fan.
5. This unit is to be used for the control
of ceiling fans and in an AC230/240V
50Hz power supply only.
6. The remote receiver must be used
within its load rating of 100 watt
maximum.
7. Do not install in damp locations or
immerse into water. (For indoor use
only.)
8. The batteries will weaken with age
and should be replaced before
leaking takes place as this will
damage the transmitter.
Overload Protection for Fan Motor
If your fan or light suddenly goes off, check
the protection fuses.
Installation of
TransmitterWall Mount
Holderwith two screws
Fan Off
Indicator
Light
Fan Timers
1 to 8 hours
Light
On/Off
Fan On - Slow
Fan On - Low
Fan On - Medium
Fan On - Medium High
Fan On - High
TRANSMITTER
RECEIVER PLACEMENT
RECEIVER CONNECTION
Block
terminal
WHITE
(Light/Live)

WIRING DIAGRAM
t+27 (0) 31 563 4600 | [email protected] | www.solent.co.za
Transmitter Functions
Fan Off
1. Fan On - Slow
2. Fan On - Low
3. Fan On - Medium
4. Fan On - Medium High
5. Fan On - High
Light On/Off + Dimmer
Transmitter & Receiver Pairing
1. Within 30 seconds from the power being
switched on, press the FAN OFF button until
the light on the fan flashes once and the
fan starts rotating.
2. Pairing is now complete.
Timer Function
1. There are 5 Timers– 1 hour, 2 hours, 4 hours,
6 hours and 8 hours.
2. The Timer must be set while the fan is in
rotation and it can be set on any speed.
3. Press the desired Timer to put the fan in
sleep mode and the fan will turn off when
the selected Timer is reached.
Receiver Connection
1. Connect the RECEIVER as shown in
wiring diagram.
Receiver Placement
1. Once the connection is made, place the
RECEIVER in the canopy, slide the canopy
up and tighten in position.
Receiver Memory Function
1. After a power outage or a tripped circuit
breaker, the fan will default to
Light OFF and Fan ON.
The fan will run at the speed
that was last saved in memory.
RemoteLD5
RemoteLD5 - Fan Five Speed with Light On/Off and Dimmer
IMPORTANT POINTS
1. Caution: Do not use this product in
conjunction with any wall/speed
regulator.
2. Please note that all fixed wiring
appliances should be installed by a
qualified electrician.
3. The supply to the remote control
receiver should be connected
through a mains switch, i.e. existing
wall switch.
4. Disconnect from power supply at
wall switch before working on remote
control receiver or ceiling fan.
5. This unit is to be used for the control
of ceiling fans and in an AC230/240V
50Hz power supply only.
6. The remote receiver must be used
within its load rating of 100 watt
maximum.
7. Do not install in damp locations or
immerse into water. (For indoor use
only.)
8. The batteries will weaken with age
and should be replaced before
leaking takes place as this will
damage the transmitter.
Overload Protection for Fan Motor
If your fan or light suddenly goes off, check
the protection fuses.
Installation of
TransmitterWall Mount
Holderwith two screws
Fan Off
Indicator
Light
Fan Timers
1 to 8 hours
Light
On/Off
+ Dimmer
Fan On - Slow
Fan On - Low
Fan On - Medium
Fan On - Medium High
Fan On - High
TRANSMITTER
RECEIVER PLACEMENT
RECEIVER CONNECTION
Block
terminal
WHITE
(Light/Live)