5566
Function buttons
1
2
Each time the button is pressed, the operation
mode is selected in a sequence of following:
3
MODE Button
1
2
4
5
3
8
10
9
4
5
ON/OFF Button( )
Operation starts when this button is pressed
and stops when this button is pressed again.
NOTE: Heat mode is for Cooling & Heating models only.
AUTO
COOL
DRY
HEAT FAN
6
7
11
12
13
14
SHORTCUT(MEMORY SHORTCUT) Button
NOTE: While the unit is running under SLEEP
mode, it would be cancelled if press the MODE,
FAN SPEED or ON/OFF button.
TIMER ON Button
Used to restore the current settings or
resume previous settings.
On the first time connecting to the power,
if push the SHORTCUT button, the unit
O
will operate on AUTO mode, 24 C, and fan
speed is Auto.
Push this button when remote controller is
on, the system will automatically revert back
to the previous settings including operating
mode, setting temperature, fan speed level
and sleep feature(if activated). And transmit
the signals to the unit.
If push this button when remote controller
is off, the system will only resume the
previous settings and will not transmit
the signals to the unit. And the sleep
feature is disable.
If pushing more than 2 seconds, the system
will automatically restore the current
operation settings including operating mode,
setting temperature, fan speed level and
sleep feature(if activated ).
15
8
6
7
MOD E
SWING TEM P
SHORTCUT
FAN
SPEED
TIMER
OFF
RESET LOCK
LED
FOL LOW ME
TIMER
ON
TURBO
SEL F CLEAN
DIRECT
SLEEP
FRESH
1
2
4
5
3
9
10
8
6
7
11
12
13
14
15
TURBO
SE LF
CL EAN
SLEEP
FRESH
SHORT
CU T
TIMER
ON
TIMER
OF F
LOC K RES ET
LED
FOL LOW
ME
FA N
SPEED
DIRECT
SWING
MODE
TEM P
RG35A(2) RG36A(1)
SWING Button
DIRECT Button
Used to stop or start horizontal louver auto
swing feature.
Used to change the louver movement and set
the desired up/down air flow direction. The
O
louver changes 6 in angle for each press.
Active/Disable SLEEP function. If pushing
more than 2 seconds, the FRESH function
will be activated, pushing more than 2
seconds again to disable.
SLEEP/FRESH Button
,
,
Active/Disable TURBO function. If pushing
more than 2 seconds, the SELF CLEAN
function will be activated, pushing more than
2 seconds again to disable(depending on
models).During the heating operation(only
when the setting mode is HEAT),press this
button and the unit will operate at a setting
O
temperature of 8 C.The display window of indoor
unit will display FP.Press the buttons of ON/OFF,
SLEEP,FP,MODE,FAN SPEED,UP,DOWN and
SHORTCUT while operating will cancel the FP
function.
TURBO/SELF CLEAN(or FP) Button:
,
,
When you press the recessed RESET button,
all current settings are cancelled and the
control will return to the initial settings.
RESET Button:
Push this button to decrease setting temper-
ature or to decrease Hour during Timer setting.
UP Button( )
Push this button to increase setting temper-
ature or to increase Hour during Timer setting.
DOWN Button( )
9
-
+
12
10
11
Used to select the fan speed in four steps:
AUTO LOW MED HIGH
FAN SPEED Button
Press this button to initiate the auto-on time
sequence. Each press will increase the
auto-timed setting in 30 minutes increments.
When the setting time displays 10H, each
press will increase the auto-timed setting
60 minutes increments. To cancel the
auto-timed program, simply adjust the
auto-on time to 0:0.
1
2
4
5
3
8
10
9
6
7
11
12
13
14
15
MOD E
SWI NG TE MP
SHO RTC UT
FAN
SPEED
TIMER
OFF
RESET LOCK
LED
FOL LOW ME
TIMER
ON
TURBO
FP
DIR ECT
SLE EP
RG35A1
1
2
4
5
3
9
10
8
6
7
11
12
13
14
15
TURBO
FP
SLEEP
SHORT
CU T
TIMER
ON
TIMER
OF F
LOC K RES ET
LED
FA N
SPEED
DIRECT
SWING
MODE
TEM P
RG36B1
,,
,,
ON /O FF
ON /O FF
ON/OFF
