SOLIDDRIVE SD1 Operating manual

INDUCTION DYNAMICS®
INSTALLATION & USE GUIDE
for SolidDrive SD1 into walls and
ceilings before drywall
INDUCTION DYNAMICS®True Audio PerfectionTM
Experience True
Audio Perfection
Induction Dynamics extensive
line of audio products makes
it easy to create the ultimate
audio system, regardless of
installation requirements.
Induction Dynamics builds
these products with only the
most select components and
materials; and utilizes numerous
unique and proven technologies.
TM

Figure 1. SolidDrive SD1 mounting bracket attached to wall studs.
Place the mounting bracket between the wall studs
or ceiling joists and secure with two, 1 3/8" drywall
screws. Insert the screws through the 2 pre-drilled
holes in each flange and screw them into the face of
each wall stud or ceiling joist (Figure 1). The drywall
screws need to be driven flush with the surface of the
flange so that the drywall sets flush on the bracket
flange.
Feed the SolidDrive SD1 cable through the round
opening in the face of the mounting bracket. Insert
the SolidDrive SD1 through the same opening with
the oversized mounting base facing outwardtoward
the side that the drywall will be installed and flush
against the bracket face. Align the pre-drilled holes in
the mounting base to the threaded holes in the bracket
face (Figure2). Attach the SolidDrive SD1 securely to
the mounting bracket using the 4 Phillip’s flat head
machine screws.
STEP 1. Attach the SolidDrive SD1 mounting
bracket to wall studs or ceiling joists.
STEP 2. Insertthe SolidDriveSD1 into the bracket.
Figure2. SolidDriveSD1 being installed into mounting bracket
INSTALLATION OF SOLIDDRIVE
SD1 INTO WALLS AND
CEILINGS BEFORE DRYWALL
By utilizing these six basic installation steps,
you can install the SolidDrive SD1 into walls
and ceilings before drywall to create sound
for boardrooms, home theater, and distributed
audio.
Getting Started with SolidDrive
What’s included with the SolidDrive SD1 for
installation into walls and ceilings before
drywall and what is supplied by the installer
ASolidDrive SD1 consists of:
One (1) SolidDrive SD1 unit and attached wiring
harness with Eurostyle connector. *Additional
mounting materials may need to be ordered with
the SolidDrive SD1 or supplied by the installer
depending on the application.
For drywall: For in-wall and in-ceiling installation,
you will have ordered one (1) or more SolidDrive
SD1s and one (1) or more patent-pending acoustic
in-wall mounting brackets (one (1) bracket per SD1),
which comes with four (4) #8-32 x 5/16'' Phillips
flat head machine screws for mounting the drive to
the bracket.
At the time of the order, you will have specified
16OC, 24OC or 12OC. *Installation also requires
four (4) 1 3/8'' drywall screws and one (1) container
of 3M®Super 77 Spray Adhesive(supplied by the
installer).
s

normal mud and tape routine. The joint compound
placed between the panels will improve the distribution
of sound as well as the overall sound quality.
The surface material plays a key role in the system’s
sound performance. To ensure an optimal listening
experience the installer MUST equalize the SolidDrive
SD1 system. Equalization is accomplished by using the
SolidDrive Drywall Passive Equalization Module or
using the auto equalization feature available on some
receivers. *Additional information about the
SolidDrive Drywall Passive Equalization Module can
be found on the back cover of this guide.
INSTALLATION IS NOW COMPLETE – ENJOY THE
SOLIDDRIVE SD1 SOUND SYSTEM
Now that you’ve completed the installation process
and equalization, you can enjoy the True Audio
Perfection of the Induction Dynamics SolidDrive
SD1 sound system.
HIGH OUTPUT INSTALLATIONS
For installations requiring high output, such as a
home theater or other high output type applications,
two SolidDrive SD1’s should be used for each of the
high output channels. For example the left, right, and
center channel of a home theater or the left and right
channels of a high output stereo system. The two
SD1’sshould be wired in series for each of the high
output channels (Figure 4). For maximum output each
SolidDrive channel should have available at least 20
square feet of surface area.
STEP 3. Make the electrical connections.
Figure 4. SolidDrive SD1’s wired in series for high output installations
Figure 3. Eurostyle connector
Make the electrical connection between the SolidDrive
SD1 and the speaker cable using the Eurostyle connector
attached to the end of the SolidDrive SD1 audio cable.
The polarity of the wiring is clearly indicated (Figure 3).
If possible, position the drywall panel so that the
SolidDrive SD1 is at the center of the panel or as far
from the edge of the panel as possible. This will allow
proper distribution of sound and the SolidDrive SD1
will function with optimum performance. Prior to
mounting, take measurements of the new drywall
panel to determine the exact area that will come in
contact with the base of the SolidDrive SD1 and spray
that area liberally with the 3M®Super 77 contact
spray adhesive. Also, liberally spray the surface of the
oversized mounting base of the SolidDrive SD1
(masking around the base is highly recommended to
prevent overspray). IMPORTANT: Failure to apply the
adhesive to both the drywall surface and oversized
mounting base will prevent the system from function-
ing properly.
Immediately install the drywall beforethe spray
adhesive sets up (approximately 10 minutes). This
allows adjustment of the panel before the final
location is determined. The drywall panel is to be
fitted to the wall studs or ceiling joists and screwed
into position. Apply joint compound in the crack
between the drywall panels and proceed with the
STEP 5. Install the new drywall panels.
STEP 6. Equalize the SolidDrive SD1 sound system
STEP 4. Apply adhesive to the drywall surface
and base of the SolidDrive SD1.

Type Full Range Transducer
Impedance 8 Ohm
Frequency Response (Hz) 70 Hz to 15 kHz
Recommended Amplifier Power 10 – 100 Watts
Dimensions 2.28" Diameter x 2.08" Height
Mounting Plate 3.5'' Diameter
Weight 1.2 lb / .54 kg
SolidDrive SD1 Specifications
Type Patent-pending balanced cantilever
spring bracket
Construction Heavy duty, galvanized steel
Dimensions 16OC – 2.0" H x 17.5" W
24OC – 2.0" H x 25.5" W
12OC – 2.0" H x 13.5" W
Weight 1.0 lb / .45 kg
SolidDrive SD1 In-Wall and
In-Ceiling Mounting Bracket
Specifications
Connector Type Eurostyle
Wire Size 16 gauge
Dimensions 1.0" H x 2.875" W x 2.0" D
Weight .27 lb / .12 kg
SolidDriveDrywall Passive
Equalization Module Specifications
SolidDrives, SolidDrive Subwoofers, and A4
Amplifier come with a 7-year warranty.
SOLIDDRIVE DRYWALL PASSIVE
EQUALIZATION MODULE
The SolidDrive Drywall Passive Equalization Module
increases the system’s sound performance for optimal
listening enjoyment by using notch filters to correct
peaks in the frequency response. Use one (1) module
with each SolidDrive SD1.
WARRANTY
The product is guaranteed for 7 years from date of purchase. Any misuses
or modifications to this equipment in any way will void the warranty.
WARNING
Read instructions prior to operating. To reduce the risk of fire or electric
shock, do not expose this product to rain or moisture. Unplug prior to
cleaning and clean with a damp cloth. There are no user-serviceable parts
in this product, please refer all servicing to qualified personnel.
www.inductiondynamics.com / www.soliddrive.com
8650 College Boulevard •Overland Park, KS 66210 •TEL: [phone] •FAX: [phone]
INDUCTION DYNAMICS®True Audio PerfectionTM
TM