Solla 5000LM User manual

LED Motion Sensing Security Light Retain this manual for future reference. Read the instructions carefully prior to installation![e-mail] WWW.SOLLA.USWWW.FACEBOOK.COM/SOLLALED

SAFETY INSTRUCTION1. DO NOT install the fixture near an air condition unit or flammable materials. 2. DO NOT install it in a place with limited ventilation, high vibration level or high ambient temperatures. 3. DO NOT look directly at the light source when it is on, as this may cause irreparable damage to the eyes. 4. Risk of suffocation! Keep small parts and packaging materials away from children. 5. Non-professionals are forbidden to disassemble, repair or modify this product.Prior to the installation, service or routine maintenance, please read the following general precautions.SPECIFICATIONSH: 5000LM±10%M: 4000LM±10%L: 3000LM±10%5000~5500K36W2835 56pcs*3AC100V~240V≥80≤10mA72ft/40ft/20ft10mins/5mins/1minIP65Luminous FluxColor TemperatureCurrent Consumption LED BeadsInput CRIStandby CurrentSensitivity Setting Time Setting Ingress Protection- 1 -

EN PRE-INSTALLATION10 cm (3.94 in)10 cm (3.94 in)×￭ Optimum installation height: 2.5 m (8.25 ft) WallGround2.5 m (8.25 ft)1.Mounting Height and LocationsnIt is recommended to install the light under eaves or awnings.￭ Keep the fixture level with the ground. ￭ Leave at least 10 cm space from the top or ceiling and side wall.￭ Install the fixture on a flat surface and a relatively stable place.- 2 -
√

INSTALLATIONMounting AccessoriesA.Iron Plate x 1B.Screw x 2C.Screw x 1D.Screw x 1E.Silicone plug x 1F.Light Fixture x 1G.Wiring Cover x 1Installation Procedure1.Install the Iron Plate (A) on the junction box in right direction and tight it with screws (B).2.Remove the Wiring Cover (G) from the light.3.Wiring the Light FixtureCAUTION: Make sure polarity is correct as shown below.■ The ends of the mains cable should leave enough length to make it easy to make connections.■ Connect the mains cable to the Connector Block. Insert the blue wire from the original power supplier into the terminal marked "N".Insert the brown wire from the original power supplier into the terminal marked "L".Insert the green/yellow earth wire from the original power supplier into the terminal marked "〨 ".- 3 -

- 4 -4.Remove the silicone plug amid the Wiring Cover (G), then install the Wiring Cover (G) on the junction box and tight it with screw (C). Then cover the hole with silicone plug.5.Mount the light fixture (F) on the Wiring Cover assembly, tight it with screw (D)and cover it with silicone plug(E).OPERATION 1.Lamp Heads Adjustment￭ The left and right lamps can be adjusted 180 degrees up or down. The middle lamp can be adjusted 90 degrees up or down. ￭ The left and right lamps can be adjusted 90 degrees backward or forward.￭ The triangle bracket can be adjusted 45 degrees left or right. 2.Motion Sensor Adjustment90°180°90°90°45°45°90°90°￭ The sensor can be adjusted 90° degrees left or right.

4.Warm-up State￭ Warm-up state The light fixture will enter a warm-up state for 20 seconds when it is energized with AC100`240V for the first time: The three adjustable light heads are switched off, the 12 function indicators will light gradually for 20 seconds; 20 seconds later, three heads will light and the light fixture is ready to be set.￭ Function indicator When the light on standby mode detects the motion, four function indicators showing the current level will keep light on for 5 seconds. - 5 -72ft40ft20ftD2DTEST10min5min1minDISTMODEDIM3.Detection RangeDetection Range: around 72 ft/21m * 180 degrees (Max.) 180°0°20ft/6m10ft/3m150°80°30°40ft/12m72ft/21m72ft/21m40ft/12m20ft/6m8.25ft2.5m

- 6 -5.Custom SettingsWithin 72ft(21M)High sensitivityDetection DistanceDimmingHigh Brightness
Medium Brightness
Low BrightnessLight up for 10 minsLight up for 5 minsLight up for 1 mins Infrared human body sensing modeDawn to Dusk Mode Switch72ft40ft20ftWithin 40ft(12M)Medium sensitivityWithin 20ft(6M)Low sensitivityD2DTEST10min5min1minLight up 5 secondsDISTMODEDIMTime SettingPress the setting buttons to customize your light fixture:DIST: The sensor will detect motion within 72ft/40ft/20ftMODE:￭ Infrared human body sensing mode: The light fixture will be triggered when the sensor detects the human body.￭ Dawn to Dusk mode: The light fixture will turn off in the daytime and turn on at night automatically, light up for 10 hours.￭ Test mode: The light fixture will light up for 5 seconds.The fixture will light up for 10 mins/5 mins/ 1min when the motion is detected.DIM: The light fixture is dimmable.(5000lm/4000lm/3000lm)

6.Motion SensorInfrared human body sensing mode: When the sensor detects the moving heat source, three light heads will be turned on and the motion sensor will turn blue and stay for 5 seconds, indicating that the sensor works properly.Dawn to Dusk mode:In this mode, the light fixture will be switched to energy-saving mode by decreasing the lumen by 50% when there is no moving heat source detected within 10 minutes. If detected the heat source, the light will return to the normal brightness, meanwhile the motion sensor will turn blue and stay for 5 seconds. - 7 -