Solomon SR-073 User manual

Warning!
Using the machine, the following basic measures should be abide, avoid electric shock or
cause injury or damage caused by fires.
2. To ensure personal safty, must use the orginal approval or recommendation of the parts,
otherwise it will lead to serious consequences.
3. Machine failure must be by professionals or the company designated personnel for repair.
4. This product is grounded three-wire plug, must be inserted within the threehole grounded outlet,
do not change the plugs or use ungrounded three adapter made it bad grounded.
5. When the hot air gun or soldering station is turned on, its temperature all has the possibility to
amount to above 400 degrees. Do not use it near flammable gas, objects. Tube and the heat
emitted very hot, can burn the body, don not bouch the hot pipe and direct injection to heat the
human body.
6. Hot air gun is turned on, do not leave the jobs site.
7. Do not install nozzle when the hot air gun is turned on. It must be installed after the heating pipe
and the gun are cooling down.
8. Please keep inlet and outlet air flow, it can not be clogging.
9. After used, remember cooling the station, the handle should be released into the handle frame,
then shut down the machine to sleep.
10. The machine welding will take smoke, please do proper ventilation.
1. In order to ensure the personal safety, when the machine work is completed, please unplug
the power cord.
Specification
Model
Input voltage
Power
Heater type
Airflow type
Airflow value
Temperature range
Temperature stability
Shows type
Handle line
Noise
Work Environment
Storage Environment
Storage humidity
SR-073
AC 220V / AC 110V
≦550W
Skeleton
Diaphragm pump
≦24L / min
100℃ ~ 450℃
±1℃
LED / display
≧100cm
≦45dB
0 ~ 40℃
-20 ~ 80℃
35% ~ 45%
SMD REWORK STATION
AIR GUN
INSTRUCTION MANUAL
SR-073
Thank you for choosing this type of unsoldering Equipment with Hot Air. The product
is designed for soldering and unsoldering without lead. Please read the User Guide
thoroughly before use, and keep it in a safe place for future reference.
HOT
CAUTION
Iron
AIR
POWER
5V 2A
AUTO MANUAL
ESD
SAFE
Lead-free design Air pump Volution outlet
SR-073
1
2
3
4 5
6
7
8
SMD REWORK STATION
Manual / automatic
HEATER
100 480
℃
Heater Lamp
Temperature Control Knob
(Refer to the Temperature Distribution Chart)
Air Flow
Lamp
Air Flow Control Knob
(Refer to the Air Flow Distribution Chart)
Temperature Display
USB Output
Auto(Stand by) / Manual(Working Condition)
Power Switch
Air Gun Stand

Usage
1. Rework for a variety of components such as: SOIC, CHIP, QFP, PLCC, BGA, etc.
(Especially for phone cable and welding cable split seat)
2. For shrink, drying, paint, adhesive removal, thawing, warm, and plastic welding.
Operating Instructions
1. Put the air gun on the air gun stand.
2. Connect the power
3. Equipment required nozzle( try to using bigger nozzle).
4. When turn on SR-073 enters working mode, LED shows “---”, rework station is standby.
5. Rotate the temperature control knob to set the working temperature.
6. Picked up the handle, the station will enter normal heat welding working station.
Air volume adjustment knob to the right airflow, after waiting for temperature stability
it can normal operation.
7. SR-073 work is completed, the handle must be placed on the holder. And then the
station will cut off the hot air automatically to send cold air cooling heating mode. When
the temperature less than 100, LED display “---” that machine will enter standby mode.
8. Long termed not used must be cut off the power.
Note:
If it possible make use of low temperature and large air volume, that good for save
heating element of the life and safety disoldering IC chip.
Set up the Temperature and Airflow
1. LED digital display microcomputer-based hot air reowrk station:
* In the energized, rotating the temperature control knob temperature. The LED will
display set temperature. After two seconds, real-time temperature display shows
“---” into standby(The handle should be on the holder).
2. After set up the temperature, adjust the air flow to the right to work.
Explanation of symbols
1. Shows “---” mean the air temperature less 100℃, the station enter standby and the gun
should be on the holder.
2. Shows “ S-E ” mean the station sensor have problem should be replaced the heater
(Heating material and sensor components).
3. When working, the display temperature less than 50℃, and no longer to heat up, that the
heater may be damaged and need to replace the heating element(heating material and
sensor components).
Terms of Use
1. Hot air rework station and surrounding the outlet may have a very high temperature, should be
careful to guard against burns.
2. Heating, the handle must be on the holder, not be placed on work surfaces or other places.
3. Please keep the air gun not have obstructions.
4. After work, must turn off the power, SR-073 gun handle must be placed on the holder, the
machine automatically cooled to below 70℃(into standby), and then turn off the power swtich.
5. When using outlet should be kept the distance with the goods at least 2mm, as per outlet to
calculated.
6. As work requirements, choose the appropriate nozzle, different nozzle, different temperature.
OPTION PARTS mm(inch)
“The size in Name/Specification indicates the size of IC package.”