SOMFY WTT animeo IB+ User manual

© 2007-2017, SOMFY ACTIVITÉS SA, Société Anonyme. ALL RIGHTS RESERVERD. REF. 5057571C - 2017/12/05
WTT animeo IB+/IB • REF. 5057571C - 4/4
A. This installation test tool offers the following
possibilities
1. Sending of animeo IB+ telegrams for examination of the C and
IB+ ( ) wires on the 4 wire bus as well as the correct rota-
tion direction of the motors.
2. Sending of animeo IB up/down orders for examination of the C,
Up and Down (st) wires of the IB bus.
3. Short circuit detection between the C and IB+ ( ) wires of
the animeo 4 wire bus.
4. Programming of the Motor Controller local switch allocation to
the motor outputs, individual or grouped.
B. Preliminary conditions
1. All blinds within the tested zone should be in the upper end limit position (completely up).
Check the position of the blinds from the outside of the building!
2. Examine whether wind conditions allow to drive the blinds.
3. Connections of the local switches between Motor Controller of different zones are not allowed
without using the switch zone splitter.
4. Battery test of the WTT (3 V battery type CR 2430). A “low battery“ is indicated by 4 simultane-
ously flashing LEDs on the WTT after pressing one of the buttons on the device. Be sure that the
device is not yet connected to the system. If the “low battery“ indication appears, replace it
before continuing! The life span of the battery amounts to approx. 2000 send instructions.
5. Remove the bus connection from the Building Controller to the Motor Controller zone and at-
tach the WTT to the Motor Controller zone.
UP
STOP
DOWN
MODE
E. Grouping of the local switches on the Motor Controller
1. Identify the Motor Controllers to program and disconnect them from the IB+ bus. Connect the
WTT to the Motor Controller(s) which have to be programmed.
Attention: This order is transfered to all connected Motor Controllers.
2. Enable the function by pushing the button on the back of the WTT at least
3 seconds. On = 2 x outside-inside running light on the WTT.
3. Choose the wanted switch configuration with the Up-button on the WTT.
You have 8 possibilities to choose from. The choice will be displayed with
the 4 LEDs on the WTT.
Red = Motor 1, Orange = Motor 2, Yellow = Motor 3, Green = Motor 4.
Example: All 4 LEDs on the WTT blink one by one = Each switch controls 1 motor
4. By pressing the Stop button on the WTT, the current chosen combination can be visualised.
5. Send the order by pushing the mode button. Again, your choice is indicated by the LEDs on the WTT.
6. Test via the local switch if your configuration succeeded.
7. Disable the grouping function by pushing the button on the back for 3 seconds.
Off = 2 x inside-outside running light on the WTT.
F. Battery
1. Unloose screws and remove cover of Wiring Test Tool.
2. Remove used battery and insert new one (Type CR 2430).
3. Proper disposal of used battery.
m Batteries or accumulators have to be separated from other type
of waste and must be recycled through your local treatment and
recycling system.
min. 3 s.
① ②
③
WT T animeo IB+/IB
Wiring Test Tool
Installation guide
50 Avenue du Nouveau Monde, 74300 Cluses, France
somfy.com/projects
somfy.com/ce
©2007-2017, SOMFY ACTIVITÉS SA - Société Anonyme - capital 35.000.000 €, RCS ANNECY 303.970.230. ALL RIGHTS RESERVED. REF. 5057571C – 2017/12/05 100 % recycled paper

WTT animeo IB+/IB • REF. 5057571C - 2/4 WTT animeo IB+/IB • REF. 5057571C - 3/4
C. Detectable errors
Error 1: Motor Controller without supply
Error 2: Missing IB+ transmission to the Motor Controller
Error 3: Short circuit in the IB+ bus, between the C and IB+ wire (a short circuit
is indicated by 4 simultaneously flashing LEDs on the wiring test tool)
Error 4: Inverted up/down motor connection
Error 5: Broken fuse for the corresponding motor output
Error 6: Broken motor or missing connections
Error 7: Inverted up/down wires or short circuit on the IB bus. Start to look for the error from the
Motor Controller which is closest to the Building Controller
Error 8: Wiring mistake on the local switches
Remark: When running long test sequences the thermal protection of the mo-
tors could be activated. In this case wait 30 minutes before continuing.
D. Wiring test sequence
1. Testmode on by pressing
(1 sec) the button on the back
of the tool.
Testmode on = orange LED blinks
3 x. Running light on all connected
Motor Controllers. During the
test mode, all local switches are
disabled!
Error 1
Error 2
Error 3
After correc-
tion,
repeat this
step until the
running light is
enabled on all
Motor Control-
lers
4. Test mode off by pressing
(1 sec) the button on the back of
the tool.
Test mode off = yellow LED blinks 3 x. The running light on the
Motor Controller stops. All local switches are enabled again!
2a. IB+ Down order. Order
indicated on WTT by blinking of
the red and the green LED.
Visual check of all blinds in the zone.
All blinds move down for approx.
10 sec.
Wrong running
direction
Error 4
Does not move
Error 5
Error 6
After correction,
repeat step 2a
and 2b until
o.k.
2b. IB+ Up order. Order indi-
cated on WTT by blinking of the
red and the green LED.
Visual check of all blinds in the zone.
All blinds move up for approx. 10 sec.
3a. Switching to IB mode in order to test the C, up and down (st) wires of the IB bus.
(You may switch from IB to IB+ by pushing the mode button for 3 sec)
3b. IB Down order. Order
indicated on WTT by blinking of
the red and the yellow LED.
Visual check of all blinds in the zone.
All blinds move down to the lower
end limit.
Error 7
After correction,
repeat step 3b
and 3c until o.k.
3c. IB Up order. Order indicated
on WTT by blinking of the red
and the orange LED.
Visual check of all blinds in the zone.
All blinds move up to the upper end
limit.
WTT Command Reaction Possible error
WTT order Reaction Possible error
5. Check each of the local switches in the building individually! Error 8