Sonic Modell HD WING User manual

Page | 1
Assembly Instrucons for:
SONICMOELL HD WING

Page | 2
Thank you for purchasing the SonicModell HD WING!
intended to be a short to medium range FPV aircra .
The HD Wing is easy to operate with
excellent flight characteriscs, but we do not recommend a flying wing as a beginner airframe
for FPV unless they have assistance
from an experienced pilot .
Please obey all current laws and use common sense for safety when operang.
Note: We reserve the right to modify informaon presented and cannot be held liable for errors
within.
Required to operate:
Motor – 2212 2200KV (Included in PNP)
Propeller – 6x4 E (Included in PNP)
ESC – Hobby Wing 30A (Included in PNP)
Servos – 2x 9g (Included in PNP)
Baeries – 3s 2200-4200
Required for assembly:
Epoxy or personal choice of glue
Medium and Small Phillips screw driver
Hobby Knife
Servo Centering Tool
It is import to read the manual in its enrety before your maiden flight. This model is

Page | 3
Package Contents: (KIT version Show)
Fuselage
Hardware Package
a. Upper and Lower Wing Bracket Joiners with Screws
b. Oponal Wooden Camera Plate
Main Wings
Landing Skids
Wing Spar
Oponal Nose with Domes
Rudders
Decal Sheet

Page | 4
Assembly
1. Locate Wing Spar and feed it half way through the fuselage.
2. Locate Right and Le wings and slide each side over the spar unl they reach
the center. Aileron servos should be on top.

Page | 5
3. Locate Plasc wing Anchors and Screws. Each anchor has corresponding leers
and a forward poinng arrow in the plasc that note where each one belongs.
a. Longer screws go in the forward brackets.
b. All screws insert from the boom side. If you have any that insert from
the top, please double check.
c. Fasten screws unl snug. Do not over ghten and compress foam.

Page | 6
4. Locate Servo Leads and pass them through to the fuselage.
a. You will see a small opening inside the fuselage to pull the lead through.

Page | 7
5. Locate landing skids and dry fit before gluing into place.
a. If you use the nose piece to help guide the skids, be careful to not allow
glue onto it. We use contact cement.
b. Secure the skids with masking tape while curing.

Page | 8
6. Locate rudders, screws and secure into place. It is not necessary to glue the
rudders into place.

Page | 9
7. Locate oponal dome nose and 2 small screws.
a. Secure dome onto nose with screws.
8. Locate prop adapter, propeller, and adapter rings. Install onto motor sha and
ghten completely.
a. It is always best to balance the propeller before flying.
b. Note proper direcon. The “leers” printed on the prop always face
forward.

Page | 10
9. Oponal – If you are not planning on using the equipment cut-outs, you may
want to glue or tape them in place before flying.
10. Seng up the HD Wing
for maiden flight:
a. Aer you have successfully installed and bound your radio and receiver,
verify that all channels are operang on the correct controller input and
in the correct direcon for flight. The HD Wing will require “mixing”
since it
is a model with elevons.
b. Set the elevon throws to 100% or approximately 15mm of travel in both
direcons. (Measured in relaon of the elevon to the wing)
c. Center of Gravity (CG) is achieved directly on the raised leering on the
boom of the wings (24mm forward of the wing spar). We recommend
that the model is slightly nose heavy for the maiden flight.
d. Without FPV gear installed, we fly with an 3300 3s baery.
e. While the HD Wing is an easy plane to hand launch, we recommend
qualified person to launch for the maiden flight.
having a

Page | 11
Center of Gravity Mark:
Finished the HD Wing:
Enjoy your HD Wing ! Please fly responsibly.
CG Bump