Canon Creative Park Pteranodon User manual

Cut line
Valley fold
Mountain fold
Glue up to this line
Cut in line
Tools
Keep scissors and glue away from small children.
Be careful not to cut your fingers when using scissors.
Caution
Assembly Instructions Explanation of Symbols
Glue tab
Attach to a point within the same piece
Glue tab
Attach to a separate piece
1: Carefully cut out the parts.
2: Fold along the dotted lines, making mountain or valley folds
as indicated.
3: Attach the glue tabs on each part to assemble the model.
(Read the assembly instruction for more information.)
4: Attach the parts in order.
(Read the assembly instruction for more information.)
5: Your paper craft model is finished!
Scissors, glue (We recommend craft glue.)
Pteranodon : Assembly Instructions
This is a paper craft of a pteranodon
in flight with its wings spread wide.
The pteranodon is one of the most
well-known winged dinosaurs.
Believed to have existed in the late
Cretaceous period of the Mesozoic
era, pteranodons have large,
distinctive crests, and a wingspan of
around 7 to 9 meters. Display this
paper craft by placing it on the stand
included, or use string to hang it from
the ceiling!
Pteranodon

1. Add curves to , and assemble it.
*Assemble in the same way.
Assemble the head
3. After assembling and , attach them to . Then, fit it on to the head and attach it in place.
Tuck these two glue tabs under the bill
and glue them underneath.
Put a little glue on the tip of the bill too.
Attach in line with the curved parts.
2. Assemble , and attach it to .
Assemble by attaching these two glue tabs only.
Pteranodon : Assembly Instructions

4. Attach to the head by inserting it inside. Then, assemble , fit it on to the head from the bottom and attach it in place.
Assemble by attaching these two glue tabs only.
Insert this part into the head.
5. Assemble , and attach it to the head by inserting it inside.
Put a little glue on the tip too.
6. Assemble , and , and attach to the head.
Pteranodon : Assembly Instructions

1. Assemble , and attach it to . Next, cut away the piece on marked by the curved line.
2. Roll the sections marked A, B and C and glue them to form cylinders.
3. Attach the left and right wings together. Next, assemble , and glue it to the wings.
After attaching the pieces together, fold these parts back and then glue them down.
Align these straight lines and attach together.
A
C
B
Assemble by fitting B over A.
*Assemble and in the same way.
is a reinforcing part, so attach it securely.
It should look like this viewed from the side.
Assemble the wings
Pteranodon : Assembly Instructions

Assemble the body
2. Assemble , and attach it to .
3. Attach and as shown, to the assembled wings.
If you want to hang it up with string,
thread the string through at the two
points marked by arrows.
Glue firmly to the straight lines
(marked here in green).
If you have threaded string, tie it up
to keep it out of the way.
Turn it over, and attach the glue tabs together.
First, attach the pieces at these two glue tabs only.
1. After assembling , attach and , and cut away the piece marked by the curved line.
Pteranodon : Assembly Instructions

4. Assemble , and attach it to the body.
5. Assemble and , and attach it to the body.
1. After attaching and , attach them to the wings.
Assemble the feet
Glue the tips of the claws together too.
*Assemble and in the same way.
Pteranodon : Assembly Instructions

2. After assembling , cut away the piece marked by the curved line.
3. Attach and to the wings, and attach the head to the body.
4. Attach and together.
Do not put glue on these areas.
*Assemble in the same way.
Glue the tips of the claws together too.
*Assemble and in the same way.
Pteranodon : Assembly Instructions

5. Assemble , and attach it to .
6. Attach the legs to the body, and your pteranodon is complete.
1. Attach , and , place the pteranodon on top, and you're done!
Assemble the stand
*Do not apply glue.
*Assemble in the same way.
Pteranodon : Assembly Instructions