SONNEMAN 2850 User manual

©2018 SONNEMAN - A WAY OF LIGHT
1 of 2
January 2, 2018
LED Product Information and Warnings
Important
• Always disconnect the power before installing or replacing bulbs and before cleaning or other maintenance.
• Consult a qualified, licensed electrician to ensure correct branch circuit conductor.
• Please read all included assembly instructions and warnings carefully before installation. Contact
Customer Service if you have any questions or concerns. Before installation, please conrm that the xture
is compatible with your supply voltage and dimming system, if present.
• LEDs are highly sensitive electronic devices, and must be treated with care. Do not open any factory
sealed compartments, and avoid touching the LEDs with your hands or any object.
• Although all our xtures are equipped with protective devices, LED xtures are vulnerable to power surges
and supply variations. Do not install LED xtures on the same circuit as any motors, appliances, or HVAC
systems.
• Do not remove or bypass any LED Driver or Transformer that is provided with the xture, and do not
replace or substitute with another power supply.
• Remote LED Driver or Transformer installation must be done by a licensed electrician and in accordance
with local codes. Remote installations should be in an accessible location, as close to the xture as possible.
• Fixtures must be wired in parallel on independent leads; do not "daisy chain" multiple xtures together or
wire them in series.
• All factory-made splices and connections must remain intact. LED circuits are carefully designed and built,
and improper connections may damage the xture.
• The ends of coaxial pendant cords have been precisely stripped and split at the factory and must not be
eld cut. Excess cord or cable should be neatly coiled and reserved in the xture canopy.
• Any mounting hardware is provided for your convenience and should be used with discretion. Always use
the appropriate hardware for the mounting surface.

©2018 SONNEMAN - A WAY OF LIGHT
2 of 2
January 2, 2018
Assembly Instructions 2850, 2852, 2853, 2854, 2855
INSTRUCTIONS D’INSTALLATION
Votives Series - LED Sconce, 1' LED Wall Bar, 4' LED Wall Bar, 6' LED Wall, 8' LED Wall
Important
• Always disconnect the power before installing and before cleaning or other maintenance.
• Consult a qualified, licensed electrician to ensure correct branch circuit conductor.
Consulter un électricien qualifié pour vous assurer que les conducteurs de la dérivation sont adéquats.
1. Shut o power to the outlet box.
2. The LED driver (A) must be installed in a remote and accessible location near the xture in accordance with local electrical
code. (Fig. 1)
a. Connect the LED driver’s live wire (black) to the live supply wire.
b. Connect the LED driver’s neutral wire (white) to the neutral supply wire.
c. Connect the LED driver's positive (+) output wire (red) to the necessary length of red wire (not included) to reach the
xture location.
d. Connect the LED driver's negative (-) output wire (black) to the necessary length of black wire (not included) to reach the
xture (B) location.
3. Drill a small hole (C) in the wall behind the xture and pull the low voltage wires through the wall.
4. Attach the mounting plate (D) to the structure, secure with drywall screws (E)
and drywall anchors (F).
5. Make appropriate electrical connections using wire nuts:
a. Connect the positive (red) low voltage wire to the red xture wire.
b. Connect the negative (black) low voltage wire to the black
xture wire.
c. Carefully place the connections in the back of the xture (B).
6. Install the xture (B) to the mounting plate (D) by
hooking the bar in the xture onto
the upper bend on the mounting plate (D).
Secure with set screws (G)
using included Allen key (H).
7. Screw diusers (J) into the xture (B).
8. Restore power to the outlet box (A).
Note
• 2850, 2852 & 2853: These fixtures are dimmable with Electronic Low Voltage (Trailing-Edge) type dimmers and
Incandescent (Leading-Edge) type dimmers. For best performance, we recommend using an Electronic
Low Voltage Dimmer.
• 2854 & 2855: This fixture is dimmable with ELV (Trailing-Edge), Incandescent (Leading-Edge), and 0-10V type
dimmers only.
Care Instructions
• Dusting: Use a clean, dry cloth.
• Cleaning: To protect the finish, avoid any harsh abrasives or chemicals.
Fig. 1
A
H
D
FGB
J
C
E
2853
2850
2852
2853
2854
2855