CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716
CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK
• For printed wiring boards.
•b: Pattern from the side which enable seeing.
(The other layer's patterns are not indicated.)
• Circled numbers refer to waveforms.
• Through hole is omitted.
• There are few cases that the part printed on diagram isn’t
mounted in this model.
• Chip parts.
Transistor Diode
• For schematic diagrams.
• All capacitors are in µF unless otherwise noted. pF: µµF.
50V orlessare not indicatedexcept forelectrolytics and tantalums.
• Chip resistor are 1/16W unless otherwise noted.
kΩ:1000Ω, MΩ:1000kΩ.
• Caution when replacing chip parts.
New parts must be attached after removal of chip.
Becarefulnot toheatthe minussideof tantalumcapacitor, because
it is damaged by the heat.
• Some chip part will be indicated as follows.
Example C541 L452
22U 10UH
TA A2520
• Constants of resistors, capasitors, ICs and etc with XX indicate
tha they are not used. In such cases, the unused circuits may be
indicated.
• Parts with differ according to the model/destination. Refer to
the mount table for each function.
• All variable and adjustable resistors have characteristic curve B,
unless otherwise noted.
• Signal name
XEDIT nEDIT PB/XREC nPB/REC
•2: non flammable resistor.
•1: fusible resistor.
•H: panel designation.
•A: B+ Line
•B: B– Line
•J: IN/OUT direction of (+, –) B LINE.
•C: adjustment for repair.
• Circled numbers refer to waveforms.
4-8 4-9
CD-210/211 (CCD IMAGER) PRINTED WIRING BOARD
– Ref No. CD-210 BOARD: 4,000 series, CD-211 BOARD: 9,000 series –
CCD IMAGER
CD-210/211
Note on the CCD imager replacement
• The CCD imager is not mounted for the already mounted
CD-210/211 board supplied as the repair parts.
When replacing the CD-210/211 board, remove the CCD im-
ager from the old board and install on the new board.
• Perform all adjustments of the camera block when the CCD
imager has been replaced.
• Handle the CCD imager with attention such as MOS IC as it
may be broken by static electricity in the structure.
Also, prevent the receiving light section from dust attached
and strong light.
• For Printed Wiring Boards.
•Chip transistor
There are few cases that the part isn't mounted in this model is
printed on this diagram.
C
Q
BE
4-2. PRINTEDWIRING BOARDS AND SCHEMATIC DIAGRAMS
THIS NOTE IS COMMON FOR PRINTEDWIRING BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.)
• Measuring conditions voltage value and waveform.
• The object is color bar chart of pattern box.
• Voltages and dc between ground and measurement points.
Readings are taken with a digital multimeter (DC 10MΩ).
• Voltages variations may be noted due to normal production
tolerances.
1.Connection
2.Adjust the distance so that the output waveform of Fig. a and the
Fig. b can be obtain.
Fig. b (Picture on monitorTV)
Fig. a (Video output terminal output waveform)
Pattern box
1.5m
Kinds of capacitor
(
Â
External dimensions (mm)
Â
Temperature
chracteristics
Les composants identifiés par
une marque !sont critiques
pour la sécurité.
Ne les remplacer que par une
piéceportantle numéro spécifié.
The components identified by
mark !ordottedline withmark
!are critical for safety.
Replace only with part number
specified.
When indicating parts by refer-
encenumber,please includethe
board name.
4-7
Lens reference plane
surface lmaging surface
of CCD imager
(IC401 on CD-197/198 board)
Electron beam
scanned frame
CRT picture frame
Yellow
Cyan
Green
White
Magenta
Red
Blue
ABBA
A=B
H
Yellow
Cyan
Green
White
Magenta
Red
Blue
C
Q
BE
5 46
132
Q
5 64
312
Q
54
312
Q
21
Q
534
3
21
3
21
3
21
Refer to page 3 as for “Table for difference
of functions” of models and classification.
CD-210/211 BOARD
CAMERA REC
H
7Vp-p
IC401
1 2
1
2
3
,
H
7Vp-p
IC401
3 4
H
1.3Vp-p
IC401
7
,
CD-210/
CD-211 BOARD
C401 A-3
C403 B-3
C405 A-3
C406 A-3
C407 B-3
CN401 B-4
IC401 A-1
L401 B-1
Q402 B-3
R401 A-3
R404 B-3
R405 A-3
R406 B-4
VF-99...
B/W EVF models only
(B/W EVF)
PD-107...
TRV series only
RGB decoder, LCD,
LCD drive, Back light
CF-61...
TRV series only
(Control) SE-80...
TR716 only
SE-81...
TRV series only
(Steady shot)
CD-210...
TR series only
CD-211...
TRV series only
(CCD imager)
1-672-464- 11 21
1-672-458- 11
CD-210/211 BOARD (SIDE B) CD-210/211 BOARD (SIDE A)
1234
A
B
C
09
321