manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Sony
  6. •
  7. Car Receiver
  8. •
  9. Sony XR-CA624X Product guide

Sony XR-CA624X Product guide

Cautions
•This unit is designed for negative earth 12 V
DC operation only.
•Do not get the wires under a screw, or caught
in moving parts (e.g. seat railing).
•Before making connections, disconnect the
earth terminal of the car battery to avoid short
circuits.
•Connect the yellow and red power input leads
only after all other leads have been connected.
•Run all earth wires to a common earth
point.
•Be sure to insulate any loose unconnected
wires with electrical tape for safety.
Notes on the power supply cord (yellow)
•When connecting this unit in combination with
other stereo components, the connected car
circuit’s rating must be higher than the sum of
each component’s fuse.
•When no car circuits are rated high enough,
connect the unit directly to the battery.
Parts Iist (1)
The numbers in the list are keyed to those in the
instructions.
Caution
Handle the bracket 1carefully to avoid injuring
your fingers.
Connection example (2)
Notes (2-A)
• Be sure to connect the earth cord before
connecting the amplifier.
• If you connect an optional power amplifier and do
not use the built-in amplifier, the beep sound will
be deactivated.
Tip (2-B-
)
For connecting two or more changers, the source
selector XA-C30 (optional) is necessary.
Connection diagram (3)
1To a metal surface of the car
First connect the black earth lead, then connect
the yellow and red power input leads.
2To the power aerial control lead or power
supply lead of aerial booster amplifier
Notes
• It is not necessary to connect this lead if there
is no power aerial or aerial booster, or with a
manually-operated telescopic aerial.
• When your car has a built-in FM/MW/SW aerial
in the rear/side glass, see “Notes on the control
and power supply leads.”
3To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.
4To the +12 V power terminal which is energised
in the accessory position of the ignition key
switch
Notes
• If there is no accessory position, connect to the
+12 V power (battery) terminal which is
energised at all times.
Be sure to connect the black earth to it first.
• When your car has a built-in FM/MW/SW aerial
in the rear/side glass, see “Notes on the control
and power supply leads.”
5To the +12 V power terminal which is energised
at all times
Be sure to connect the black earth lead to it first.
Notes on the control and power supply leads
• The power aerial control lead (blue) supplies +12 V
DC when you turn on the tuner.
• When your car has built-in FM/MW/SW aerial in
the rear/side glass, connect the power aerial
control lead (blue) or the accessory power input
lead (red) to the power terminal of the existing
aerial booster. For details, consult your dealer.
• A power aerial without relay box cannot be used
with this unit.
Memory hold connection
When the yellow power input lead is connected,
power will always be supplied to the memory circuit
even when the ignition key is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms,
and with adequate power handling capacities to
avoid its damage.
• Do not connect the speaker terminals to the car
chassis, or connect the terminals of the right
speakers with those of the left speaker.
• Do not connect the earth lead of this unit to the
negative (–) terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active
speakers (with built-in amplifiers) to the speaker
terminals may damage the unit.
3-227-101-11 (1)
Installation/Connections
安裝線路連接
########
FM/MW/SW
Cassette
Car stereo
Sony Corporation © 2001 Printed in Thailand
XR-CA624X
1
12
×4
3
4675
×2
Equipment used in illustrations (not supplied)
插圖中的裝置(非附送)
######
Power amplifier
功率放大器
########
CD/MD changer
CD/MD換碟機
#######
Front speaker
前揚聲器
######
Rear speaker
後揚聲器
#######
2
BBUS AUDIO IN
BUS CONTROL IN
TV tuner unit
電視機調諧器裝置
######
BUS CONTROL IN
BUS AUDIO IN
A
TV monitor
電視監視器
#########
Rotary commander RM-X4S
旋轉式控制器 RM-X4S
###########
AUDIO OUT
Source selector
音源選擇器
######
*
*
*not supplied
非附送
#####
AUDIO OUT
FRONT
AUDIO OUT
REAR
BUS
AUDIO
L
R
3
from car aerial adaptor
來自汽車天線轉接器
################
BUS AUDIO IN
Source selector
音源選擇器
########
1
4
5
2
AMP REM
ANT REM
7
Left
左
#####
Right
右
#####
Left
左
#####
Right
右
#####
RCA pin cord (not supplied)
RCA 針型插頭電線(非附送)
###############
Max. supply current 0.3 A
最大電流 0.3 A
##############
Max. supply current 0.1 A
最大電流 0.1 A
##############
Fuse (10 A)
保險絲(10 A)
#########
Red
紅色
#######
Yellow
黃色
#######
Black
黑色
#######
Blue
藍色
########
Blue/white striped
藍白條紋
#############
White
白色
#######
Green
綠色
#########
Purple
紫色
##########
White/black striped
白黑條紋
#########
Grey/black striped
灰黑條紋
#########
Green/black striped
綠黑條紋
#########
Purple/black striped
紫黑條紋
#############
BUS CONTROL IN
Grey
灰色
#####
警告
•本機祇能使用負極接地 12 V 直流電源。
•不要使導線夾在螺栓下,或繞掛在移動部件上
(如:座椅扶手上)。
•連接前,先拔去汽車電池的接地端子,以免發生
短路。
•黃色和紅色電源輸入導線必須在所有其它導線都
連接完畢以後才連接。
•將所有地線都連接到同一接地點。
•為了安全,請確認把沒有連接的導線用電器膠帶
包紮進行絕緣。
電源導線須知(黃色)
•將本機與其它立體聲裝置相連接時,所連接的
汽車電路容量必須大於每個裝置保險絲容量的
總和。
•當汽車電路容量不夠大時,請將本機直接與電
池相連接。
零件一覽表(1)
圖示數字與說明書中的數字是一致的。
警告
拿取裝卸支架 1 時,請特別注意別傷到手指。
線路連接圖例(2)
註
(2-A)
•
務必在接放大器之前連接地線
。
•
如果您連接了選購件的功率放大器而不使用內置的放
大器,將無報警聲功能
。
提示
(2-B- )
若要連接 2 台或 2 台以上換碟機時,必須使用音源選擇
器 XA-C30(選購件)。
線路連接圖(3)
1至汽車的金屬表面
首先連接黑色接地導線,然後再連接黃色和紅色電源
輸入導線。
2至電動天線控制導線或天線升壓放大器的電源導線
註
•
如無電動天線、增壓器或手動操作的伸縮天線,便
不需連接此導線。
•
您的汽車的後玻璃窗中如果有內置 FM/MW/SW 天線,
即請參看“控制和電源線須知”。
3至選購的功率放大器的 AMP REMOTE IN(放大器遙控
輸入)
本連接僅用於放大器。連接任何其它系統可能會損壞
本機。
4至在點火鑰匙的輔助位置上通電的 +12 V 電源端子
註
•
若沒有輔助位置,則請連接至常時通電的 +12 V 電
源(電池)端子。
務請首先將黑色接地導線與其連接。
•
您的汽車的後玻璃窗中如果有內置 FM/MW/SW 天線,
即請參看“控制和電源線須知”。
5至常時都通電的 +12 V 電源端子
務請首先將黑色接地導線與其連接。
控制和電源線須知
•
接通調諧器電源時,電動天線的控制導線(藍色)便
能提供 +12 V 直流電。
•
若您的汽車後玻璃窗上有內置 FM/MW/SW 天線,須將
電動天線控制導線(藍色)或輔助電源輸入導線(紅
色)連接到現有天線放大器上的電源端子上。詳細內
容請向銷售商諮詢。
•
本機不能使用不具備繼電箱的電動天線。
保持記憶的線路連接法
當連接好黃色電源輸入導線時,即使汽車發動機點火鑰匙
被轉在電源切斷之處,電源仍繼續將電流供給記憶用電路,
以保持所記憶著的數據。
連接揚聲器時的注意事項
•
連接揚聲器電線以前,請先切斷本機電源。
•
使用阻抗為 4-8Ω 且具有充分功率處理容量的揚聲
器,以免損壞揚聲器。
•
不要將揚聲器端子連接到汽車底盤上或將右揚聲器端
子與左揚聲器端子相連接。
•
切勿將本機的接地導線連接至揚聲器的負(-)接線柱。
•
揚聲器不可以並聯連接。
•
請僅連接無源揚聲器。若將有源揚聲器(帶內置放大
器)連接到揚聲器端子上會損壞本機。
Insert with the cord
upwards.
電線向上插入。
###############
REMOTE IN
AUDIO OUT
Supplied with the CD/MD changer
附帶於 CD/MD 換碟機
##########
3
Supplied with XA-C30
附帶於 XA-C30
#########
XR-CA624X
Cautions
•This unit is designed for negative earth 12 V
DC operation only.
•Do not get the wires under a screw, or caught
in moving parts (e.g. seat railing).
•Before making connections, disconnect the
earth terminal of the car battery to avoid short
circuits.
•Connect the yellow and red power input leads
only after all other leads have been connected.
•Run all earth wires to a common earth
point.
•Be sure to insulate any loose unconnected
wires with electrical tape for safety.
Notes on the power supply cord (yellow)
•When connecting this unit in combination with
other stereo components, the connected car
circuit’s rating must be higher than the sum of
each component’s fuse.
•When no car circuits are rated high enough,
connect the unit directly to the battery.
Parts Iist (1)
The numbers in the list are keyed to those in the
instructions.
Caution
Handle the bracket 1carefully to avoid injuring
your fingers.
Connection example (2)
Notes (2-A)
• Be sure to connect the earth cord before
connecting the amplifier.
• If you connect an optional power amplifier and do
not use the built-in amplifier, the beep sound will
be deactivated.
Tip (2-B-
)
For connecting two or more changers, the source
selector XA-C30 (optional) is necessary.
Connection diagram (3)
1To a metal surface of the car
First connect the black earth lead, then connect
the yellow and red power input leads.
2To the power aerial control lead or power
supply lead of aerial booster amplifier
Notes
• It is not necessary to connect this lead if there
is no power aerial or aerial booster, or with a
manually-operated telescopic aerial.
• When your car has a built-in FM/MW/SW aerial
in the rear/side glass, see “Notes on the control
and power supply leads.”
3To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.
4To the +12 V power terminal which is energised
in the accessory position of the ignition key
switch
Notes
• If there is no accessory position, connect to the
+12 V power (battery) terminal which is
energised at all times.
Be sure to connect the black earth to it first.
• When your car has a built-in FM/MW/SW aerial
in the rear/side glass, see “Notes on the control
and power supply leads.”
5To the +12 V power terminal which is energised
at all times
Be sure to connect the black earth to it first.
Notes on the control and power supply leads
• The power aerial control lead (blue) supplies +12 V
DC when you turn on the tuner.
• When your car has built-in FM/MW/SW aerial in
the rear/side glass, connect the power aerial
control lead (blue) or the accessory power input
lead (red) to the power terminal of the existing
aerial booster. For details, consult your dealer.
• A power aerial without relay box cannot be used
with this unit.
Memory hold connection
When the yellow power input lead is connected,
power will always be supplied to the memory circuit
even when the ignition key is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms,
and with adequate power handling capacities to
avoid its damage.
• Do not connect the speaker terminals to the car
chassis, or connect the terminals of the right
speakers with those of the left speaker.
• #####.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active
speakers (with built-in amplifiers) to the speaker
terminals may damage the unit.
182 mm
53 mm
4A
Precautions
•Choose the installation location carefully so
that the unit will not interfere with normal
driving operations.
•Avoid installing the unit in areas subject to
dust, dirt, excessive vibration, or high
temperatures, such as in direct sunlight or near
heater ducts.
•Use only the supplied mounting hardware for
a safe and secure installation.
•There must be a distance of at least 15 cm between
the cassette slot of the unit and shift lever in order
to insert a cassette easily. Choose the installation
location carefully so the unit does not interfere
with gear shifting and other driving operations.
15 cm
Mounting angle adjustment
Adjust the mounting angle to less than 20°.
How to detach and attach the
front panel (4)
Before installing the unit, detach the front
panel.
4-A To detach
Before detaching the front panel, be sure to
press (OFF). Press (OPEN), then slide the front
panel to the right side, and pull out the left side.
4-B To attach
Place the hole in the front panel onto the
spindle on the unit as illustrated, then push
the left side in.
B
Mounting example (5)
Installation in the dashboard
Mounting the unit in a Japanese
car (6)
You may not be able to install this unit in some
makes of Japanese cars. In such a case, consult
your Sony dealer.
Note
To prevent malfunction, install only with the
supplied screws 4.
Warning when installing in a car
without ACC (accessory)
position on the ignition key
switch
Be sure to press (OFF) on the unit for two
seconds to turn off the clock display after
turning off the engine.
When you press (OFF) only momentarily, the
clock display does not turn off and this causes
battery wear.
RESET button
When the installation and connections are
completed, be sure to press the RESET button
with a ballpoint pen, etc.
1 2 3
Bend these claws outward
for a tight fit, if necessary.
若有必要,則可彎曲這些卡爪。
#####
2
6
4
4
5
54
4
1
1
Fire wall
防火壁
#####
Dashboard
儀表板
#####
5
5
c
使用前注意事項
•仔細選擇安裝位置,使之不妨礙正常的駕駛操作。
•避免將本機放在高溫之處,如陽光直接照射、暖
氣機前、或灰塵極多、髒亂,以及極易受震動等
地方。
•為使安裝得以安全和可靠,祇能使用提供的安裝
零件。
•在本機的卡帶槽口和變速桿之間,至少需保持
15 cm 距離以便於裝插卡帶。請留心選擇安裝位
置以便使機器不至於妨礙您排檔和其他駕車操
作。
15 cm
安裝角度之調整
請在 20 °以內調整安裝角度。
如何拆卸和裝配前面板(4)
安裝本機之前,請先拆卸前面板。
4-A 拆卸
拆卸前面板之前,須先按下 (OFF) 鍵。然後,按
下 (OPEN) 鍵以便開啟前面板,將前面板稍微向
右邊滑動,然後將前面板的左側拉出。
4-B 裝配
如圖所示,將前面板的 孔搭在本機的支軸
上,然後推入左側。
安裝示例(5)
安裝在儀錶板裡
將本機安裝於日本產汽車上時
(6)
有的日本產汽車不能安裝本機,在這種情形下,請
您向當地的 Sony 經銷商諮詢。
註
為防止發生故障,安裝時只能使用附送的螺絲
4
。
安裝在點火鑰匙開關上沒有 ACC
(輔助)位置的汽車上時的警告
在關掉汽車引擎之後,一定請按下機器上的
(OFF) 兩秒以關掉時鐘顯示。
如果只短暫地按一下 (OFF),將不會關掉時鐘顯
示而浪費電池。
RESET 按鈕
當安裝和連接完成後,務請用圓珠筆等按壓 RESET
按鈕。
3
6A
to dashboard/center console
至儀表板中央控制箱
################
Bracket
托架
########
Bracket
托架
#########
max. size
5 ×8 mm
最大尺寸
5×8 mm
#########
#########
B
4
max. size
5 ×8 mm
最大尺寸
5×8 mm
#######
########
TOYOTA NISSAN
4
to dashboard/center console
至儀表板中央控制箱
#################
Bracket
托架
#######
Bracket
托架
######
4
Existing parts supplied with your car
隨汽車附送的部件
##########################################
Existing parts supplied with your car
隨汽車附送的部件
#########################
max. size
5 ×8 mm
最大尺寸
5×8 mm
#######
##########
max. size
5 ×8 mm
最大尺寸
5×8 mm
##########
#####
4
Precautions
•Choose the installation location carefully so
that the unit will not interfere with normal
driving operations.
•Avoid installing the unit in areas subject to
dust, dirt, excessive vibration, or high
temperatures, such as in direct sunlight or near
heater ducts.
•Use only the supplied mounting hardware for
a safe and secure installation.
•There must be a distance of at least 15 cm between
the cassette slot of the unit and shift lever in order
to insert a cassette easily. Choose the installation
location carefully so the unit does not interfere
with gear shifting and other driving operations.
15
cm
Mounting angle adjustment
Adjust the mounting angle to less than 20°.
How to detach and attach the
front panel (4)
Before installing the unit, detach the front
panel.
4-A To detach
Before detaching the front panel, be sure to
press (OFF). Press (OPEN), then slide the front
panel to the right side, and pull out the left side.
4-B To attach
Place the hole in the front panel onto the
spindle on the unit as illustrated, then push
the left side in.
Mounting example (5)
Installation in the dashboard
Mounting the unit in a Japanese
car (6)
You may not be able to install this unit in some
makes of Japanese cars. In such a case, consult
your Sony dealer.
Note
To prevent malfunction, install only with the
supplied screws 4.
Warning when installing in a car
without ACC (accessory)
position on the ignition key
switch
Be sure to press (OFF) on the unit for two
seconds to turn off the clock display after
turning off the engine.
When you press (OFF) only momentarily, the
clock display does not turn off and this causes
battery wear.
RESET button
When the installation and connections are
completed, be sure to press the RESET button
with a ballpoint pen, etc.

Other Sony Car Receiver manuals

Sony XR-1800 User manual

Sony

Sony XR-1800 User manual

Sony CDX-R3300 - Fm/am Compact Disc Player Guide

Sony

Sony CDX-R3300 - Fm/am Compact Disc Player Guide

Sony CDX CDX-GT210 Product guide

Sony

Sony CDX CDX-GT210 Product guide

Sony CDX-GT550UI - Fm/am Compact Disc Player Product guide

Sony

Sony CDX-GT550UI - Fm/am Compact Disc Player Product guide

Sony CDX-GT25MPW - Fm/am Compact Disc Player User manual

Sony

Sony CDX-GT25MPW - Fm/am Compact Disc Player User manual

Sony XR-4800 User manual

Sony

Sony XR-4800 User manual

Sony Xplod CDX-GT130 User manual

Sony

Sony Xplod CDX-GT130 User manual

Sony DSX-S100 Product guide

Sony

Sony DSX-S100 Product guide

Sony DSX-MS60 User manual

Sony

Sony DSX-MS60 User manual

Sony CDX-M9900 Operating Instructions  (primary... User manual

Sony

Sony CDX-M9900 Operating Instructions (primary... User manual

Sony XAV-W650BT User manual

Sony

Sony XAV-W650BT User manual

Sony CDX-C90R User manual

Sony

Sony CDX-C90R User manual

Sony EXCD-31 User manual

Sony

Sony EXCD-31 User manual

Sony CDX-1300 - Fm/am Compact Disc Player User manual

Sony

Sony CDX-1300 - Fm/am Compact Disc Player User manual

Sony XR-CA800 User manual

Sony

Sony XR-CA800 User manual

Sony XR-C430RDS Product guide

Sony

Sony XR-C430RDS Product guide

Sony CDX-L480X Product guide

Sony

Sony CDX-L480X Product guide

Sony MDX-C7900R User manual

Sony

Sony MDX-C7900R User manual

Sony CDX-GT710 - Fm-am Compact Disc Player Assembly instructions

Sony

Sony CDX-GT710 - Fm-am Compact Disc Player Assembly instructions

Sony HCD-D890AV User manual

Sony

Sony HCD-D890AV User manual

Sony CDX-L350 - Fm/am Compact Disc Player User manual

Sony

Sony CDX-L350 - Fm/am Compact Disc Player User manual

Sony MEX-BT3700U Product guide

Sony

Sony MEX-BT3700U Product guide

Sony CDC-X217 Instruction Manual

Sony

Sony CDC-X217 Instruction Manual

Sony HCD-H61 User manual

Sony

Sony HCD-H61 User manual

Popular Car Receiver manuals by other brands

Hitachi KM-900T Service manual

Hitachi

Hitachi KM-900T Service manual

TOP VEHICLE TECH GR4MBZ1 installation manual

TOP VEHICLE TECH

TOP VEHICLE TECH GR4MBZ1 installation manual

Kenwood KDC-PS907 instruction manual

Kenwood

Kenwood KDC-PS907 instruction manual

JVC KD-DV5306 Installation & connection manual

JVC

JVC KD-DV5306 Installation & connection manual

JVC KD-G511 instructions

JVC

JVC KD-G511 instructions

Pioneer Super Tuner III DEH-P90HDD Operation manual

Pioneer

Pioneer Super Tuner III DEH-P90HDD Operation manual

JVC KD-G436 instructions

JVC

JVC KD-G436 instructions

Audiovox AVDBR1 owner's manual

Audiovox

Audiovox AVDBR1 owner's manual

Kenwood DPX-5000BT instruction manual

Kenwood

Kenwood DPX-5000BT instruction manual

AMS CT410 Prediagnostic

AMS

AMS CT410 Prediagnostic

Kenwood DDX6027 Service manual

Kenwood

Kenwood DDX6027 Service manual

DAB CK-O DAB2011 user manual

DAB

DAB CK-O DAB2011 user manual

Clarion Addzest DXZ825 owner's manual

Clarion

Clarion Addzest DXZ825 owner's manual

Sanyo CDF-R800 operating instructions

Sanyo

Sanyo CDF-R800 operating instructions

Jensen VM9510 owner's manual

Jensen

Jensen VM9510 owner's manual

Toyota Auris TAS200 2012 installation instructions

Toyota

Toyota Auris TAS200 2012 installation instructions

JVC KD-R538 instructions

JVC

JVC KD-R538 instructions

Kenwood KRC-3006 instruction manual

Kenwood

Kenwood KRC-3006 instruction manual

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.