Sony CD-R/RW User manual

CD-R/RW SCSI Drive Unit
User’s Guide
Mode d’emploi
Bedienungsanleitung
Manual de instrucciones
Manuale d’istruzione
©1999 by Sony Corporation
Rev. 1.0
BKC: 98001684
CD-R/RW SCSI Drive Unit
User’s Guide
Mode d’emploi
Bedienungsanleitung
Manual de instrucciones
Manuale d’istruzione

This unit uses CD-R discs and CD-RW discs
with the following mark.
This unit uses CD-ROM discs with the following mark.
When you use this unit as a CD player, use compact
discs with the following mark.
You are cautioned that any changes or modifications not expressly approved in this manual
could void your authority to operate this equipment.
Note:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
●Reorient or relocate the receiving antenna.
●Increase the separation between the equipment and receiver.
●Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
●Consult the dealer or an experienced radio/TV technician for help.
This CD-R/RW drive unit is classified as a CLASS 1 LASER
PRODUCT.
The CLASS 1 LASER PRODUCT label is located at the
bottom of the enclosure.
English
3
CLASS 1
LASER PRODUCT
LASER KLASSE 1
PRODUKT
Trademarks
●MS-DOS/Windows/Windows 95/98/NT are registered trademarks of Microsoft Corporation.
●Pentium is a trademark of Intel Corporation.
●IBM PC, PC/XT and PC/AT are registered trademarks of International Business Machines
Corporation.
●PHOTO CD is a registered trademark of Eastman Kodak Company.
2
Owner’s Record
The model and serial numbers are located on the top of the drive. Record these numbers in
the spaces provided below. Refer to them whenever you call upon your sales representative
regarding this product.
Model No. __________________ Serial No. ___________________
This label is located on the drive unit’s internal chassis.
Safety Regulations
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.
Caution:
As the laser beam in this CD-R/RW drive is harmful to the eyes, do not attempt to disassemble
the cabinet. Refer servicing to qualified personnel only.
The use of optical instruments with this product will increase eye hazard.
The use of controls or adjustments or performance of procedures other than those specified
herein may result in hazardous radiation.
WARNING
DANGER
INVISIBLE LASER RADIATION WHEN OPEN.
AVIOD DIRECT EXPOSIRE TOP BEAM
VORSICHT
UNSICHTBARE LASERSTRAHLUNG. WENN ABDECKUNG
GEOFFNET
NICHT DEMSTRAHL AUSSETZEN.
DANGER
DANGER
VORSICHT
ADVARSEL
ADVARSEL
VARNING
VAROI
INVISIBLE LASER RADIATION WHEN OPEN.
AVOID DIRECT EXPOSURE TO BEAM.
RADIATIONS INVISIBLES DU LASER EN CAS D'OUVERTURE.
EVITER TOUTE EXPOSITION DIRECTE AU FAISCEAU.
UNSICHTBARE LASERSTRAHLUNG, WENN ABDECKUNG GEÖFFNET.
NICHT DEM STRAHL AUSSETZEN.
USYNLIG LASERSTRÅLING VED ÅBNING.
UNDGÅ UDS/ETTELSE FOR STRÅLING.
USYNLIG LASERSTRÅLING NÅR DEKSEL ÅPNES.
UNNGÅ EKSPONERING FOR STRÅLEN.
OSYNLIG LASERSTRÅLING NÅR DENNA DEL AR ÖPPNAD.
STRÅLEN ÄR FARLIG.
NÄKYMÄTÖN AVATTAESSA OLET ALTTINA LASERSÄTEILYLLE.
ÄLÄ KATSO SÄTEESEN.
This label is located on the bottom of the drive unit enclosure.

Introduction
Features This CD-R/RW drive has the following features:
General
●5 1/4 inch half-height drive form factor.
●Fast SCSI bus interface embedded (based on SCSI-2).
●Integrated buffer memory.
●Power tray loading and ejection (manual eject too).
●Housed in an airtight frame casing.
Supported formats and modes
●CD-ROM (mode 1), CD-ROM XA (Mode 2 form 1 & 2 data)
●PHOTO-CD (read only) & Video-CD, CD-I (Mode 2, form 1 and 2)
●CD-DA, CD-EXTRA and CD-I Ready (read only)
●CD-TEXT, CD-Recordable & CD-ReWritable
Audio
●Outputs 16-bit digital audio data over SCSI interface.
●Audio CD playback via Audio Out and headphones jack.
Note:
Please read this manual thoroughly before attempting installation.
System Requirements for WINDOWS 95/98/NT
●System requirements of format software
●SCSI host adapter card (Bus Mastering)
●150 MB or more free hard disc space
●3.5" floppy disk drive
●Mouse (Microsoft-compatible)
●32 MB of RAM or more
Introduction 5
Contents
Introduction 5
Features..........................................................................................................5
System Requirements for WINDOWS 95/98/NT............................................5
Location and Function of Parts and Controls 6
Front Panel / Rear Panel................................................................................6
Precautions 7
Hardware Installation 7
Installing the Drive Unit into the Computer.....................................................7
Getting started................................................................................................7
Step 1: Opening the Computer.......................................................................8
Step 2: SCSI Configuration ............................................................................8
Step 3: Finding the Connector........................................................................9
Step 4: Choosing the Configuration................................................................9
Step 5: Setting the Jumpers.........................................................................10
Step 6: Connecting the Drive........................................................................12
Step 7: Mounting the Drive...........................................................................13
Step 8: Connecting the Power Cable...........................................................13
Step 9: Installation Review...........................................................................14
Step 10: Closing the Computer ....................................................................14
Software Installation 15
Using Discs 15
Storing Discs.................................................................................................15
Care of Discs................................................................................................15
Operating the Drive 16
Starting Up....................................................................................................16
Troubleshooting 18
Checklist .......................................................................................................18
Additional Installation Cases.........................................................................18
Technical Support.........................................................................................19
Specifications 20
Dimension diagram..........................................................Last page of manual
4

Precautions
■Installation
●Avoid placing the drive in a location subject to:
– high humidity
– high temperature
– excessive dust
– mechanical vibration
– direct sunlight.
Only horizontal drive operation recommended, not vertical or tilted.
■Operation
●Do not move drive during operation, it may cause an error.
●Avoid sudden temperature changes, condensation may form inside
the drive. Should ambient temperature suddenly change, wait at
least 1 hour before turning off power. Operation immediately after
temperature change may cause a malfunction.
■Transportation
●Keep the original packing materials for future transport of the drive.
Hardware Installation
Installing the Drive Unit into the Computer
This example assumes an IBM-PC/AT* compatible computer,
a SCSI adapter card and a SCSI interface cable (50 pin flat) are at-hand.
Getting Started
Assure SCSI adapter is operational before installing CD-R/RW drive.
●Prepare the necessary parts and tools not supplied:
– a screwdriver
– Two mounting rails if computer has mounting racks.
Precautions/Hardware Installation 7
Location and Function of Parts and Controls
Front Panel
Rear Panel
6 Location and Function of Parts and Controls
0 1 2
AUDIO OUT
R GND L
INTERFACE CONNECTOR
DC INPUT
5V±5% GND 12V±10%
ACTIVE TERM
TEST
ID SELECT
Power-in connector
SCSI bus interface connectorAudio output connector
Jumper block for SCSI bus
Headphone
Volume
Control
Busy
Indicator Disc Drawer Emergency Eject Hole Eject Button
Headphone
Jack

Step 3: Finding the Connector
The SCSI cable should have 1 or more unused connectors on the end
opposite the adapter, as shown, find a connector not in use.
We recommend a connector at the very end of the 50 pin SCSI cable.
Note:
If no free 50 pin SCSI connector exists, see “Troubleshooting”, page 18.
Step 4: Choosing the Configuration
■SCSI ID selection
●If no other SCSI devices are in the system, we recommend the default
jumper settings. In this case, go on to Step 6: “Connecting the Drive”.
●If one or more SCSI ID’s are assigned, you must determine if the
default ID# 6 is free. If SCSI ID# 6 is assigned, you must change the
CD-R drive to a free ID# via jumpers at rear of drive (see Step 5).
■Termination
●If CD-RW drive is the last physical device on SCSI cable, leave
“Active Term” jumper in place.
Previous last SCSI device may need to be “un-terminated”.
●If CD-RW drive is not on end of SCSI cable or last physical device,
remove the “Active Term” jumper and assure the last physical SCSI
device is properly terminated or activated.
Note:
Only the last physical SCSI device needs to be terminated.
Hardware Installation 9
SCSI host adapter connector Pin 1 (red) Opposite End
Step 1: Opening the Computer
First turn off computer and remove / unplug all power cables!
Remove computer cover as directed in the User’s Manual.
Step 2: SCSI Configuration
Locate the 50 pin SCSI cable in your computer. One end of the cable is
connected to the SCSI host adapter card as shown below.
Note:
The following types of cables may be installed in your computer:
Note:
There may already be internal or external SCSI devices (HDD, Scanner,
CD-ROM) connected to the SCSI cable. If so, determine the SCSI ID# of
each SCSI device. This information is required for Step 5 “Setting the
Jumpers.” Refer to SCSI device(s) for ID data. In some cases, a SCSI chip
set may be implemented on the motherboard.
1
49
50
8 Hardware Installation
SCSI
Device
SCSI
Device SCSI Device
SCSI Host Adapter Card
Red Edge
Find this
flat cable!
SCSI Cable
68 Pin*/
50 Pin
Width
40 Pin
Width 34 Pin
Width
Floppy Disk
Drive Cable
IDE Cable
*Adapter required (not included)
➧

The following table shows the function of each jumper.
Notes:
●The upper row of pins is (without position KEY) is ground.
●Remove jumper to set OFF, install jumper to set ON.
●ID SELECT, ACTIVE TERM, and TEST MODE are recognized when
the power supply is turned on or the SCSI bus is reset.
●TEST mode is used exclusively for factory testing.
Do not set TEST mode to ON. Doing so may cause unexpected
(disastrous) results.
Hardware Installation 11
Step 5: Setting the Jumpers
Set jumpers on rear of drive unit according to your computer configuration.
Jumpers are factory preset as shown below.
10 Hardware Installation
ID1
TEST
ACTIVE TERM
ID2 ID4
Jumper
ACTIVE
TERM
ID SELECT
ID number
0
1
2
3
4
5
6
Jumper settings
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
ON
OFF
OFF
ON
OFF
OFF
OFF
OFF
ON
ON
ON
TEST ON: Enables test mode
OFF: Enables normal operation
Function
ON: Enables active termination
OFF: Disables active termination
Assign the drive unit’s ID number by setting these
jumpers to ON or OFF. Do not assign the same
number as one used for other SCSI device.
Factory settings
ID1
TEST
ACTIVE TERM
ID2 ID4

Step 7: Mounting the Drive
Insert the CD-RW drive into computer front as shown, routing cables
accordingly. Secure drive to frame with appropriate screws.
Note:
Slide rails (not included) may be necessary if you cannot secure CD-RW
drive. Refer to your computer’s User’s Guide for more information.
Step 8: Connecting the Power Cable
Locate an available power supply cable, within computer, and connect it to
the rear of CD-RW drive as shown.
Note:
The power supply cable connector is designed to fit one way, do not force
it upside down, this could damage drive and void the warranty.
DC INPUT
GND 12V 10%
5V 5%
+
-+ -
Step 6: Connecting the Drive
Attach flat SCSI cable to connector at rear of CD-RW drive.
Notes:
The 50 pin flat SCSI cable must be firmly attached with its red edge
(Pin 1) positioned next to the power supply connector.
If computer has a Sound Card, an Audio Cable may be connected to the
rear of the CD-RW drive. Contact a local dealer if cable is required.
Interface Connector
Pin 1
Power Supply Connector
Red Edge
Audio
Cable
Audio Out
Connector
SCSI
Flat Cable
CD-R/W Drive Unit
Mounting Screws
Audio Cable
Flat Cable
Hardware Installation 1312 Hardware Installation
Power Supply
Connector
Power Supply Cable

Software Installation
Please refer to CD-RW formatting software/CD manual for instruction on
software installation. CD-RW formatting software must first be properly
installed in order to write CD’s with this device.
Using Discs
Storing Discs
●Do not store the disc in a location subject to:
– high humidity
– high temperature
– excessive dust
– direct sunlight
Care of Discs
●Only hold disc by its edge. Do not touch the record surface.
●Do not wipe CD-R/RW discs before recording data.
To avoid scratching the recording surface, blow away dust using an air
blower.
Software Installation/Using Discs 15
Step 9: Installation Review
Now let us review the hardware installation process, assuring that:
●All connectors are properly connected.
● Each SCSI device has its own unique SCSI ID number.
● The last physical SCSI device on the bus is properly terminated.
Notes
●Red edge of 50 pin flat SCSI cable must be on pin 1 of host adapter.
●The following is a sample configuration of CD-RW installation.
Step 10: Closing the Computer
Carefully replace computer cover, per Owner’s Manual.
Hardware installation is now complete!
14 Hardware Installation
1
49
50
Red Edge
0 1 2
AUDIO OUT
R GND L
INTERFACE CONNECTOR
DC INPUT
5V±5% GND 12V±10%
ACTIVE TERM
TEST
ID SELECT
1
2
49
50
CD-R/W Drive Power
Supply
Cable
Red Edge
SCSI Card
(Not included)
Speakers
(Not included)
Sound Card
(Not included)
Audio Cable
(included) SCSI
Cable
(Not included)

As the drive begins reading the Table of Contents (TOC) data, the busy
indicator lights and remains illuminated until read is completed.
When the busy indicator switches off, the drive is ready to receive
commands, data may be retrieved from the disc. After loading a disc,
it takes a moment for the drive to become ready while Program Memory
Area is read. From this point, follow instructions provided with the
application software.
Note:
Busy indicator on drive continues to light amber if disc is not properly
inserted or a malfunction occurs.
In such a case, eject the disc (tray) and reinsert it properly. Should
the light remain amber, consult your dealer or qualified service point.
During audio play the busy indicator remains amber, this is normal.
■Opening the drawer (tray) manually in an emergency
In the event of electrical or mechanical drive failure, a manual emergency
eject is provided to allow manual disc removal.
1Turn off the computer and remove power cable.
2Insert a pointed object, perhaps a paper clip, into the emergency
eject hole and push (typical force required is 46 N [4.7 kg]).
After thus removing disc, consult dealer or qualified service point.
Operating the Drive 17
at least 35 mm
Operating the Drive
Assure application software is installed before using the CD-RW drive.
Starting Up 1Turn on the computer.
2Press eject button and the tray extends from drive unit.
Note:
Eject button does not function if software disabled.
Insert disc into drive slot with disc label facing up.
Push gently until auto-load mechanism pulls tray into drive.
Important:
When loading a disc, do not attempt to overpower the auto-load.
16 Operating the Drive

Technical Support
If you require further support or service please contact your local Sony
technical support professionals.
For Europe (German or English) contact the hotline at:
Tel.: [phone] - 951047 or SONY-HO[email protected]
(Monday – Thursday, 8:00 am – 4:30 pm / Friday, 8:30 am – 2:00 pm)
For DK, N, SW & FIN, please call: Tel. [phone]
(Monday – Friday, 8:30 am to 4:00 pm Norwegian time)
Within the UK, please call: Tel. [phone]
(Monday – Friday, 8:45 am to 5:00 pm)
For France, please call: [phone]
(Monday – Friday, 9:00 am to 6:00 pm) or E-Mail: [email protected]
All this information and more may be downloaded from the Internet.
Simply access the following address:
http://www.sony-cp.com
Technical Support 19
Troubleshooting
Should problems occur while installing or operating the drive:
●Please verify the steps of this manual were carefully followed.
●If problem still exists, please confirm the items in ”Checklist“ below.
Checklist Please verify the following:
●Power cable properly attached to drive, Step 8 on page 13.
When properly connected, the LED lights.
●Both ends of SCSI cable are properly attached, check pin 1 position.
●SCSI ID# of CD-RW is unique to SCSI bus. Compare all other SCSI
devices (internal and external) and see Step 2 – Step 5, pages 8-11.
●Check all other jumpers on rear of drive. We recommend factory
defaults on pages 10 and 11 with a SCSI ID# 6 (if possible).
●Assure SCSI bus is properly terminated or activated at both ends.
For details, please see Step 4, Termination, on page 9.
Should you still have problems operating or installing your CD-RW drive,
please contact our hotline or your local computer dealer.
Additional Installation Cases
■ No free SCSI connector present
If other SCSI devices occupy ever bus connector, either remove a device
before installing CD-RW drive or use a SCSI cable with more connectors.
Please contact a local computer dealer for details.
■ 68 Pin SCSI Cable
If a wide SCSI cable (68 pin) is used, a 50 pin adapter is necessary.
18 Troubleshooting