Sony CFD-S45L User manual

3-864-534-11(1)
1998 by Sony Corporation
CD Radio
Cassette-Corder
EN
Operating Instructions page 2EN
Manual de instrucciones página 2ES ES
CFD-S45L
CFD-S47
CFD-S47L

Introduction2EN
Warning
To prevent fire or shock hazard, do
not expose the player to rain or
moisture.
To avoid electrical shock, do not open
the cabinet. Refer servicing to
qualified personnel only.
Information
For customers in Europe
This Compact Disc player is classified as a
CLASS 1 LASER product.
The CLASS 1 LASER PRODUCT label is
located on the bottom exterior.
Warning
Do not install the appliance in a confined
space, such as a bookcase or built-in cabinet.
Notice for customers in the United
Kingdom
A moulded plug complying with BS 1363 is
fitted to this equipment for your safety and
convenience.
Should the fuse in the plug supplied need to
be replaced, same rating fuse approved by
ASTA or BSI to BS 1362, (i.e. marked with
or mark) must be used.
If the plug supplied with this equipment has
a detachable fuse cover, be sure to attach the
fuse cover after you change the fuse. Never
use the plug without the fuse cover. If you
should lose the fuse cover, please contact
your nearest Sony service station.
About this manual
The instructions in this manual are for the
CFD-S45L, CFD-S47 and CFD-S47L. Before
you start reading, check your model number.
The CFD-S47L is the model used for
illustration purpose.
Note
The name of the switch to turn on/off this
player is indicated as below:
“OPERATE”: European countries (excluding
central and eastern Europe)
“POWER”: Other countries

3EN Introduction
Basic Operations
EN
Table of contents
Basic Operations
4Playing a CD
6Listening to the radio
8Playing a tape
10 Recording on a tape
The CD Player
12 Using the display
13 Locating a specific point in a
track
14 Playing tracks repeatedly
(Repeat Play)
15 Playing tracks in random order
(Shuffle Play)
16 Creating your own program
(Program Play)
18 Enjoying sound effects
(LOOP/FLASH)
The Radio
19 Presetting radio stations
20 Playing preset radio stations
The Timer
21 Setting the clock
22 Waking up to music
24 Falling asleep to music
Setting Up
25 Choosing the power sources
27 Selecting the audio emphasis
(Sound Mode/MEGA BASS)
Additional Information
28 Precautions
30 Troubleshooting
32 Maintenance
33 Specifications
34 Index

BasicOperations4EN
Playing a CD
Basic Operations
Connect the supplied AC power cord (see page 25).
1Press 6CD OPEN/CLOSE
(direct power-on) and place the
CD on the CD tray.
2Press ^.
The CD tray closes and the player
plays all the tracks once.
Display
Playing time
Track number
With the label side up
21
CD OPEN/
CLOSE
V
O
L
–
V
O
L
+
P
R
E
S
E
T
+
B
A
N
D
P
R
E
S
E
T
–
TUNE
–
TUNE
+

BasicOperations
Basic Operations
5EN
Use these buttons for additional operations
To Press
adjustthevolume VOL +, –
stopplayback p
pauseplayback ^(Pon the remote,
CFD-S47/S47Lonly)
Pressthebuttonagainto
resumeplayafterpause.
gotothenexttrack +
gobacktotheprevioustrack =
remove the CD 6CD OPEN/CLOSE
turnon/offtheplayer OPERATE (or POWER, see
page 2)
Tip
Next time you want to
listen to a CD, just press
^. The player turns on
automatically and starts
playing the CD.
OPERATE
(or POWER)
p
^
=
6CD OPEN/CLOSE
+

BasicOperations6EN
Listening to the radio
Connect the supplied AC power cord (see page 25).
1Press BAND until the band you
want appears in the display
(direct power-on).
2Hold down TUNE +/+or
TUNE –/=(TUNE + or – on
the remote, CFD-S47/S47L only)
until the frequency digits begin to
change in the display.
The player automatically scans
the radio frequencies and stops
when it finds a clear station.
If you can't tune in a station,
press the button repeatedly to
change the frequency step by
step.
Display
Indicates an FM stereo
broadcast
122
V
O
L
–
V
O
L
+
P
R
E
S
E
T
+
B
A
N
D
P
R
E
S
E
T
–
TUNE
–
TUNE
+
V
O
L
–
V
O
L
+
P
R
E
S
E
T
+
B
A
N
D
P
R
E
S
E
T
–
TUNE
–
TUNE
+

BasicOperations
Basic Operations
7EN
Use these buttons for additional operations
To Press
adjustthevolume VOL +, –
turnon/offtheradio OPERATE (or POWER,
see page 2)
To improve broadcast reception
Reorient the antenna for FM. Reorient the player itself
for AM or MW/LW.
for FM for AM/MW/LW
Tips
• If the FM broadcast is
noisy, press MONO/ST
ISS•PLAY MODE until
“Mono” appears in the
display and the radio
will play in monaural.
• Next time you want to
listen to the radio, just
press BAND. The player
turns on automatically
and starts playing the
previous station.
•CFD-S47 only:
If a very strong station
signal causes noise
while listening to FM
programs, set FM SENS
at the rear to LOCAL.
Normally, set it to DX.
OPERATE
(or POWER)
VOL +
MONO/ST ISS
PLAY MODE
VOL –

BasicOperations8EN
Playing a tape
Connect the supplied AC power cord (see page 25).
1Press p6 to open the tape
compartment and insert a
recorded tape. Use TYPE I
(normal) tape only. Close the
compartment.
2Press (.
The player turns on (direct
power-on) and starts playing.
With the side you want
to play facing upward
Display
12
STOP/EJECT
PLAY

BasicOperations
Basic Operations
9EN
Use these buttons for additional operations
To Press
adjustthevolume VOL +, –
stopplayback p6
f ast-forwardorrewindthetape )or 0
pauseplayback P
Pressthebuttonagainto
resumeplayafterpause.
ejectthecassette p6
turnon/offtheplayer OPERATE (or POWER,
see page 2)
Tip
Next time you want to
listen to a tape, just
press (. The player
turns on automatically
and starts playing the
tape.
p6
VOL –
P
0
OPERATE
(or POWER)
VOL +
)

BasicOperations10EN
Recording on a tape
Connect the supplied AC power cord (see page 25).
1Press p6 to open the tape
compartment and insert a blank
tape. Use TYPE I (normal) tape
only.
2Select the program source you
want to record.
To record from the CD player,
insert a CD (see page 4) and press
pon the CD section.
To record from the radio, tune in
the station you want (see page 6).
31
With the side you want to
record on facing upward
Display
STOP/EJECT
V
O
L
–
V
O
L
+
P
R
E
S
E
T
+
B
A
N
D
P
R
E
S
E
T
–
TUNE
–
TUNE
+
V
O
L
–
V
O
L
+
P
R
E
S
E
T
+
B
A
N
D
P
R
E
S
E
T
–
TUNE
–
TUNE
+

BasicOperations
Basic Operations
11EN
3Press rto start recording
((is depressed automatically).
Use these buttons for additional operations
Tips
• Adjusting the volume or
the audio emphasis (see
page 27) will not affect
the recording level.
• If the AM or MW/LW
program makes a
whistling sound after
you've pressed rin step
3, press MONO/ST
ISS•PLAY MODE
(Interference Suppress
switch) repeatedly until
the noise is at a
minimum.
• For the best results, use
the AC power as a
power source.
• To erase a recording,
proceed as follows:
1 Insert the tape whose
recording you want to
erase.
2 Press FUNCTION to
select “TAPE”.
3 Press r.
To Press
stoprecording p6
pauserecording P
Pressthebuttonagainto
resume recording.
turnon/offtheplayer OPERATE (or POWER, see
page 2)
p6
P
OPERATE
(or POWER)
MONO/ST ISS
PLAY MODE
REC
FUNCTION

TheCDPlayer12EN
Using the display
You can check information about the CD
using the display.
The CD Player
Checking the total track number and playing
time
Check the display in stop mode.
If the CD has more than 12 tracks, “OVER 12” appears
in the display.
Checking the remaining time
Press DISPLAY•ENTER MEM while playing a CD.
The track numbers in the music calendar disappear
after they are played.
To display Press DISPLAY•ENTER
MEM
thecurrenttracknumber once
and the remaining time
onthecurrenttrack*
thenumberoftracksleft twice
and remaining time on the CD
thecurrenttracknumber threetimes
and playing time
* For a track whose number is more than 20, the remaining
time appears as “– –:– –”.
Music calendar
Total playing time
Total track number
DISPLAY
ENTER MEM

The CD Player
TheCDPlayer 13EN
Locating a specific
point in a track
You can quickly find a specific point in a
track while playing a CD.
You can also locate any track using the
number buttons on the remote
(CFD-S47/S47L only).
To locate Press
apointwhilelisteningto +(forward)or =
thesound (backward)whileplaying
and hold down until you
findthepoint
apointwhileobserving +(forward)or =
thedisplay (backward)inpauseand
holddownuntilyoufind
thepoint
aspecifictrackdirectly the number button of the
(CFD-S47/S47Lonly) trackontheremote
Note
CFD-S47/S47L only:
You cannot locate a
specific track if
“SHUF” or “PGM” is lit
in the display. Turn off
the indication by
pressing p.
Tip
CFD-S47/S47L only:
When you locate a
track numbered over
10, press >10 first, then
the corresponding
number buttons.
Example:
To play track number
23, press >10 first, then
2 and 3.
+
=

TheCDPlayer14EN
Playing tracks
repeatedly
(Repeat Play)
You can play tracks repeatedly in
normal, shuffle or program play modes
(see page 16).
1Press p.
“Cd” appears in the display.
2Proceed as follows.
To repeat Do this
asingletrack 1 PressMONO/STISS•
PLAYMODEuntil“REP
1”appears.
2 Press =or +toselect
thetrackthatyouwantto
repeat.
3 Press ^.
allthetracks 1 PressMONO/STISS•
PLAYMODEuntil“REP
ALL”appears.
2 Press ^.
tracksinrandomorder 1 PressMONO/STISS•
PLAYMODEuntil“SHUF
REP”appears.
2 Press ^.
programmedtracks 1 PressMONO/STISS•
PLAYMODEuntil“PGM
REP”appears.
2 Programtracks(seestep3
on page 16).
3 Press ^.
To cancel Repeat Play
Press MONO/ST ISS•PLAY MODE until “REP”
disappears from the display.
p
MONO/ST ISS
PLAY MODE
=
^
On the remote
(CFD-S47/S47L only)
1 Press p.
2 Press MODE until
the repeat mode you
want appears in the
display.
3 Do either of the
following to start
repeat play:
•When you’ve
selected “REP 1”,
select the track by
pressing the
number button.
•When you’ve
selected “REP
ALL” or “SHUF
REP”, press (.
•When you’ve
selected “PGM
REP”, program
tracks (see step 3
on page 16), then
press (.
+

The CD Player
TheCDPlayer 15EN
Playing tracks in
random order
(Shuffle Play)
You can play tracks in random order.
1Press p.
“Cd” appears in the display.
2Press MONO/ST ISS•PLAY MODE until “SHUF”
appears in the display.
3Press ^to start shuffle play.
To cancel Shuffle Play
Press MONO/ST ISS•PLAY MODE until “SHUF”
disappears from the display.
On the remote
(CFD-S47/S47L only)
1 Press p.
2 Press MODE
repeatedly until
“SHUF” appears in
the display.
3 Press (.
p
^
MONO/ST ISS
PLAY MODE

TheCDPlayer16EN
Creating your
own program
(Program Play)
You can arrange the playing order of up
to 20 tracks on a CD.
Programed track Playing order
1Press p.
“Cd” appears in the display.
2Press MONO/ST ISS•PLAY MODE until “PGM”
appears in the display.
3Press the =or +then press DISPLAY•
ENTER MEM for the tracks you want to program
in the order you want.
The programed tracks appear in the music
calender.
4Press ^to start program play.
On the remote
(CFD-S47/S47L only)
1 Press p.
2 Press MODE until
“PGM” appears in
the display.
3 Press the number
buttons for the tracks
you want to program
in the order you
want.
4 Press (.
p
+
MONO/ST ISS
PLAY MODE
=
^
DISPLAY
ENTER MEM

The CD Player
TheCDPlayer 17EN
Tips
• You can play the same
program again, since
the program is saved
until you open the CD
tray.
• You can record your
own program. After
you’ve created the
program, insert a blank
tape and press rto
start recording.
To cancel Program Play
Press MONO/ST ISS•PLAY MODE until “PGM”
disappears from the display.
To check the order of tracks before play
Press DISPLAY•ENTER MEM.
Every time you press the button, the track number
appears in the programed order.
To change the current program
Press ponce if the CD is stopped and twice if the CD
is playing. The current program will be erased. Then
create a new program following the programing
procedure.

TheCDPlayer18EN
Enjoying sound
effects (LOOP/FLASH)
You can repeat part of a CD (LOOP) and
can “flash” the CD sound (FLASH)
during playback.
1Play a CD.
2Press and hold LOOP or FLASH at the point you
want to start the function.
To Press and hold
repeataselectedpartofaCD LOOP
“flash”theCDsound FLASH
To cancel the LOOP or FLASH function
Release the button.
The player returns to normal play.
LOOP
FLASH

TheRadio
The Radio
19EN
The Radio
Presetting radio
stations
You can store radio stations into the
player’s memory. You can preset up to
30 radio stations (CFD-S45L/S47L) or 20
radio stations (CFD-S47), 10 for each
band in any order.
1Press BAND until the band you want appears in
the display.
2Set the frequency to the station you want.
3Hold down DISPLAY•ENTER MEM for 2 seconds.
4Press PRESET + or – until the preset number (1 to
10) you want for the station flashes in the music
calender.
5Press DISPLAY• ENTER MEM again.
The new station replaces the old one.
On the remote
(CFD-S47/S47L only)
1 Press BAND to select
the band.
2 Set the frequency to
the station you want.
3 Hold down the
number buttons that
you want to preset
the new station on for
2 seconds.
The frequency digits
flash in the display
and the station is
stored into the
player’s memory.
BAND
DISPLAY
ENTER MEM
PRESET –
PRESET +

TheRadio20EN
Playing preset
radio stations
Once you've preset the stations, use the
number buttons on the remote or
PRESET +/– on the player to tune in to
your favorite stations.
1Press BAND to select the band.
2Press PRESET + or – to tune in the stored station.
On the remote
(CFD-S47/S47L only)
1 Press BAND to select
the band.
2 Press the number
buttons to tune in the
stored station.
BAND
PRESET –
PRESET +