Sony Xperia miro User manual

1266-5140 Rev 1
 Sony Mobile Communications AB – Company Internal
ST23i,ST23a
Xperia
TM
miro
Customization
-
Build S
wap
-

Customization Repair Instruction Build Swap
1266-5140 Rev 1
 Sony Mobile Communications AB – Company Internal 2(7)
CONTENTS
1 Emma Login & Script Execution...................................................3
2 Customization Workflow ...............................................................4
2.1 Customize Unit .....................................................................................5
2.2 Customize to Ship or Build Swap........................................................6
2.2.1 Customize to Ship........................................................................................6
2.2.2 Build Swap....................................................................................................6
3 Revision History.............................................................................7
For general information about Customization and Swap, refer to
1221-5655: Generic Repair Manual – build swap

1266-5140 Rev 1

Sony Mobile Communications AB
1
Emma Login & Script Execution
In order to change a phone from Customer A to Customer B you must run a ‘
followed by an ‘Activation Script’.
Start by launching the Emma application.
Connect the Micro USB to
USB cable
computer’s USB ports but do not
connect the cable to
the phone.
The USB Activation Dongle
has to be inserted
the computer’s USB ports to be able to
To execute a ‘Customization’ or ‘
Activation
application by using your
User ID and Password
To execute a ‘
Customization Script
•
check that the phone is powered off
•press and keep the ”
Volume Down
•
connect the phone to the USB Cable
•release the ” Volume Down
” key
When executing an ‘
Activation Script
Customization Repair Instruction Build Swap
Sony Mobile Communications AB
– Company Internal
Emma Login & Script Execution
In order to change a phone from Customer A to Customer B you must run a ‘
Customization Script
Start by launching the Emma application.
USB cable
to one of the
connect the cable to
has to be inserted
into one of
the computer’s USB ports to be able to
log in.
Activation
’ you need to be properly logged on to the Emma
User ID and Password
.
Customization Script
’or ‘Activation Script’ (
or any other function):
check that the phone is powered off
Volume Down
” key down on the phone
connect the phone to the USB Cable
” key
Activation Script
’
you will be prompted for the PIN of your USB Activation Dongle
Customization Repair Instruction Build Swap
3(7)
Emma Login & Script Execution
Customization Script
’
’ you need to be properly logged on to the Emma
or any other function):
you will be prompted for the PIN of your USB Activation Dongle
.

Customization Repair Instruction Build Swap
1266-5140 Rev 1
 Sony Mobile Communications AB – Company Internal 4(7)
2 Customization Workflow

Customization Repair Instruction Build Swap
1266-5140 Rev 1
 Sony Mobile Communications AB – Company Internal 5(7)
Customization Workflow
The primary reason for the customization process is to create a customized unit.
A customized unit is a unit that is ready to ship as a final swap unit.
The second reason for customization is to create “build swap” units and this can be done by selecting
the ‘Service Exchange Unit’ customization script for the particular model.
The instruction steps below refer to the flowchart on previous page.
2.1 Customize Unit
After following the steps in section 1, ‘Emma Login & Script Execution’, you can customize a phone as
follows:
•look for the Customize script for the desired Sales Item
•if that script is not available locally, select ‘Server search’ for a complete list of available scripts.
When creating a ‘build swap’ unit, select “ST23 Service Exchange Unit” as the customization
scripts!
•choose the desired script
•the application will download all necessary software to run the script and then flash that software to
the phone
•after successful update, disconnect the phone from the USB Cable
NOTE: For phones with eMMC flash memory (built in “SD card” memory), the only service
which erase this eMMC memory is Service’s “Refurbish” and “Customize”. See also emma
User Guide info. http://emma.extranet.sonyericsson.com/documents/emma_user_guide.pdf
(see “Service Types” and “Aspects of large files”)
In Swap flow, when change a phone from Customer A to Customer B, always use the service
Customization script.

Customization Repair Instruction Build Swap
1266-5140 Rev 1
 Sony Mobile Communications AB – Company Internal 6(7)
Customization Workflow
2.2 Customize to Ship or Build Swap
Is the unit a customized unit to be shipped?
Yes – proceed to 2.2.1 Customize to Ship
No – go to 2.2.2 Build Swap
2.2.1 Customize to Ship
2.2.1.1 Label Unit
Print two Core Unit labels by using ‘LabelMake’.
Place one label on the phone as described in 1266-5134: Working Instructions – mechanical.
Place the second label on the Exchange Unit Box.
‘LabelMake’ instructions to be found on CSPN under ‘LabelMake’!
2.2.1.2 Customize Mechanics
If necessary, apply the proper custom mechanical parts (co-branding, keyboard, etc.) for the variant
being created in accordance with the Cross Reference List by following the instructions of
1266-5134: Working Instructions – mechanical
2.2.2 Build Swap
2.2.2.1 Label Unit
Using a red marker, label the unit with the correct Exchange Unit number.
Refer to the Cross Reference List for the appropriate variant, which should be based on the non-
customizable mechanics of the unit.
2.2.2.2 De-Customize Unit
Remove any co-branding as described in 1266-5134: Working Instructions – mechanical

Customization Repair Instruction Build Swap
1266-5140 Rev 1
 Sony Mobile Communications AB – Company Internal 7(7)
3 Revision History
Rev
Date
Changes / Comments
1 2012-Sep-07 Initial release