Sony Dream Machine ICF-C111 User manual

1
SERVICE MANUAL
E Model
ICF-C111
FM/AM CLOCK RADIO
SPECIFICATIONS
Ver 1.1 2001. 05
Sony Corporation
Personal Audio Company
Shinagawa Tec Service Manual Production Group
9-873-094-12
2001E0400-1
© 2001.5
Time display
12-hour system (AR, E13, SP)
24-hour system (E92, MX)
Frequency range
FM: 87.5 - 108 MHz
AM: 530 - 1710 kHz
Speaker
Approx. 6.6 cm (2 5/8 inches) dia., 8 ohm
Power output
100 mW (at 10% harmonic distortion)
Power requirements
120 V AC, 60 Hz (E92, MX)
220 - 230 V AC, 50 Hz (AR, SP)
220 - 230 V AC, 60 Hz (E13)
For the power back-up function: 9V DC, one 6F22 battery
Battery life
Approx. 60 hours, using Sony S-006P (6F22) battery
Dimensions
Approx. 146.5 ×100.5 ×123 mm (w/h/d)
(5 7/8 ×4 ×4 7/8 inches) incl. projecting parts and controls
Mass
Approx. 580 g (1 lb 4.4 oz) not incl. battery
Design and specifications are subject to change without notice.
• Abbreviation
AR : Argentina model
E13 : AC 220 – 230 V area in E model
E92 : AC 120 V area in E model
MX : Mexican model
SP : Singapore model

2
TABLE OF CONTENTS
1. SERVICING NOTES
1-1. Cord Dressing (Power Cord)............................................... 3
1-2. Pointer Alignment ............................................................... 3
2. GENERAL
Setting the Clock ..................................................................... 4
Operating the Radio.................................................................4
Setting the Alarm ..................................................................... 4
Setting the Sleep Timer ........................................................... 4
3. DISASSEMBLY
3-1. Panel (Front)........................................................................ 5
3-2. Cabinet (Upper) Assy .......................................................... 6
3-3. Chassis Section ................................................................... 6
3-4. Main Board ......................................................................... 7
4. ELECTRICAL ADJUSTMENTS................................... 8
5. DIAGRAMS
5-1. Block Diagram .................................................................. 11
5-2. Printed Wiring Board ........................................................ 12
5-3. Schematic Diagram ........................................................... 13
6. EXPLODED VIEWS
6-1. Cabinet (Upper) Section.................................................... 15
6-2. Cabinet (Lower) Section ................................................... 16
7. ELECTRICAL PARTS LIST ........................................ 17
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0OR DOTTED LINE
WITH MARK 0ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
Notes on Chip Component Replacement
•Never reuse a disconnected chip component.
•Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
ICF-C111

3
ICF-C111
SECTION 1
SERVICING NOTES
1-1. CORD DRESSING
(POWER CORD)
1) Connect the power cord as shown in the figure.
2) Mount the chassis with screws (P 3 ×10).
Note: Tighten completely the screws (P 3 ×10).
1-2. POINTER ALIGNMENT
cabinet (lower) screw (P 3x10)
pwb, power cord retainer
power cord
1 Turn this in the arrow direction
until stopped.
3 Fit the protrusion on the
pointer in the hole A.
4 Align the notch on the bos
s
of the knob (turning) with
the direction of CV1.
5 MAIN board
knob (tuning)
chassis section
2 Fit the pointer in the groove.
A

4
ICF-C111
SECTION 2
GENERAL This section is extracted
from instruction manual.

5
ICF-C111
• The equipment can be removed using the following procedure.
SECTION 3
DISASSEMBLY
Note : Follow the disassembly procedure in the numerical order given.
3-1. PANEL (FRONT)
Set Panel (Front) Cabinet (Upper) Assy Chassis Section Main Board
1 screws (P 3x10)
claw
claw
claw
claws
2 panel (front)

6
ICF-C111
3-2. CABINET (UPPER) ASSY
3-3. CHASSIS SECTION
1 screws (P 3x30)
3 cabinet (upper) ass
y
2 screws (P 3x30)
2 screw (P 3x10)
3 chassis section
1 CN701
from MAIN board
from speaker

7
ICF-C111
3-4. MAIN BOARD
1 screw (P 3x10)
2 MAIN board
claw
claw

8
ICF-C111
FM FREQUENCY COVERAGE ADJUSTMENT
Adjust for a maximum reading on level meter.
L4 CT4
86.5 MHz 109.5 MHz
FM TRACKING ADJUSTMENT
Adjust for a maximum reading on level meter.
L3 CT3
86.5 MHz 109.5 MHz
AM IF ADJUSTMENT
Adjust for a maximum reading on level meter.
T1
455 kHz
AM FREQUENCY COVERAGE ADJUSTMENT
Adjust for a maximum reading on level meter.
L2 CT2
520 kHz 1,750 kHz
AM TRACKING ADJUSTMENT
Adjust for a maximum reading on level meter.
L1 CT1
600 kHz 1,400 kHz
FM SECTION 0 dB = 1 µV
Setting:
BAND switch: FM
VOLUME switch: MIN
AM SECTION
Setting:
BAND switch: AM
VOLUME switch: MIN
SECTION 4
ELECTRICAL ADJUSTMENTS
FM lead wire
antenna terminal
0.01
µ F
FM RF signal
generator
400Hz, 30% FM modulation
frequency deviation
± 22.5kHz
Output level: as low as possible
set
Put the lead-wire
antenna close to
the set.
AM RF signal
generator
400Hz, 30%
AM modulation
Output level: as low as possible
• Connecting Level Meter (FM and AM)
Repeat the procedures in each adjustment several times, and the
frequency coverage and tracking adjustments should be finally done
by the trimmer capacitors.
speaker terminal
set
16
Ω
level meter
(range: 0.5–5 V ac
)
Adjustment Location: See page 9.

9
ICF-C111
Adjustment Location:
S1
BAND
FM
AM
CN701
SP1
(SPEAKER)
SP1
1
6
CT3 CT1
CT2
CT4
CV1
TUNING
L3
L1
L4
T1
L2
VR1
CT2, L2
AM
FREQUENCY
COVERAGE
ADJUSTMENT
CT4, L4
FM
FREQUENCY
COVERAGE
ADJUSTMENT
FM
LEAD WIRE
ANTENNA CT1, L1
AM
TRACKING
ADJUSTMENT
CT3, L3
FM
TRACKING
ADJUSTMENT
T1
AM
IF
ADJUSTMENT
–MAIN board (component side) –

10
ICF-C111 SECTION 5
DIAGRAMS
THIS NOTE IS COMMON FOR PRINTED WIRING
BOARDS AND SCHEMATIC DIAGRAMS.
Common Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ωand 1/4W or less unless otherwise
specified.
•f: internal component.
•C: panel designation.
•A: B+ Line.
•H: adjustment for repair.
• Total current is measured.
• Power voltage is dc 9V and fed with regulated dc power
supply from battery terminal.
• Voltage is dc with respect to ground under no-signal
(detuned) condition.
no mark : FM
( ) : AM
• Voltagesaretakenwith a VOM (Inputimpedance 10 MΩ).
Voltage variations may be noted due to normal produc-
tion tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal produc-
tion tolerances.
• Signal path.
F: FM
f: AM
•Abbreviation
AR : Argentina model.
E13 : AC 220 – 230 V area in E model.
E92 : AC 120 V area in E model.
MX : Mexican model.
SP : Singapore model.
Note: The components identified by mark 0or dotted line
with mark 0are critical for safety.
Replace only with part number specified.
Common Note on Printed Wiring Boards:
•X: parts extracted from the component side.
•Y: parts extracted from the conductor side.
•f: internal component.
•: Pattern from the side which enables seeing.
•Abbreviation
AR : Argentina model.
E13 : AC 220 – 230 V area in E model.
E92 : AC 120 V area in E model.
MX : Mexican model.
SP : Singapore model.

ICF-C111
11 11
5-1. BLOCK DIAGRAM
28
16
9
1
|
13
23 21 22 24
27
AF POWER
AMP
FM IF
AM IF
FM
DISCRIMINATOR
5
17
18
RIPPLE
FILTER
INPUT
CONTROL
ALARM TIME CTR OUTPUT
CONTROL
DISPLAY
CONTROL
LED101
CLOCK DISPLAY
DISPLAY
DECODER/
DRIVER
OSC 1/25 or 1/30
Q201
SWITCH
Q202
16
18
19
S7
SLEEP
S3
TIME SET
M
S4
SLEEP INPUT ALARM DISP MIN SET HOUR SET SNOOZE INPUT
TIME SET
H
S7
SNOOZE/SLEEP OFF
S2
(Function Selector) +B
BUZZER
ALARM
ALARM
RADIO
RADIO ON
OFF
S6
CLOCK
S5
ALARM
D203
AR, E13, SP MODEL
DRY BATTERY
"S-006P" 9V
(IEC DESIGNATION 6F22)
AC IN ~
LED102
+B
W703
1-13
14-16
L3
CV1-3 CT3
CV1-4 CT4
CV1-1 CT1
CV1-2 CT2
CT3,L3
FM
TRACKING
L4
L1
L2
CT4,L4
FM
FREQUENCY
COVERAGE
CT2,L2
AM
FREQUENCY
COVERAGE
CT1,L1
AM
TRACKING
AM
FERRITE-ROD
ANTENNA
CV1
TUNING
T1
AM IF
FM FRONT-ENDAM FRONT-END
IC1
FM/AM
FRONT-END
IF AMP,DET
FM ANT
FM RF
FM OSC
AM ANT
AM OSC
VREG
13
10 15
8
11
6
MIX OUT CF3
CF2
T1
FM
IF IN AF IN AF OUT
NF
+B
+B
+B
+B
+B
+B
DET OUT
AM
IF IN
DISCRI
VOL
CF1
10.7MHz
VREG
Q1
VR1
w VOLUME
IC101
ALARM CLOCK
S1
BAND
FM AM
BAND SW
CN701
(1/2)
CN701
(2/2)
1
2SP1
(SPEAKER)
KEEP THE CORRECT
TIME DURING POWER
STOPPAGE
REG
FM
LEAD WIRE
ANTENNA
SLEEP
OUT
ALARM
OUT
ALARM OFF
S2-1 S2-2
D201
T2
D202 D204
D205
MAIN BOARD
TRANSFORMER
BOARD
3
• Signal path
: FM
: AM
• Abbreviation
AR : Argentina model
E13 : AC220-230V area in E model
E92 : AC120V area in E model
MX : Mexican model
SP : Singapore model
4
24 25
17
4
3
5
6
D101
E92, MX MODEL
PS101
AR, E13, SP
MODEL
E92, MX MODEL

ICF-C111
1212
5-2. PRINTED WIRING BOARD • Refer to page 10 for Common Note on Printed Wiring Boards.
1
A
B
C
D
E
F
G
H
I
J
2 3 4 5 6 7 8 9 10 11 12 13 14 15
C20
CV1-1 CV1-3
CV1-2 CV1-4
R1
BPF1
FM LEAD WIRE
ANTENNA
L3
CF3 CF2
C19
R4 T1
C5
L4
C18
C13
C10
C9 S2
C8
S7
SLEEP
S5
ALARM
S6
CLOCK
S3
TIME SET
M
S4
TIME SET
H
S8
SNOOZE/
SLEEP OFF
CF1
JW5
IC1
C7
R2
R107
R106
(SHIELD)
R104
C107
JW102
C6
JW7
Q1
Q202
R103
C210
JC103
R5
L2
C1
R6
JW3
C3
C11C12
C14
C16
C15
R105
JW207
JW101
C104
JW209
R210
R209
D205 D204
C205
C204
R204
R214 R213 R212
JC105
R120
C102 C103
JC101
R101
C101
R206
D202 D201
JC102
C202
C201
R205
C2
VR1
w VOLUME
CT3
CT1
CT2
CT4
CV1
TUNING
D101
BLK
RED
DRY BATTERY
"S-006P" 9V
(IEC DESIGNATION 6F22)
KEEP THE CORRECT
TIME DURING POWER
STOPPAGE
JW201
JW204
JW202
JW203
Q201
JW104
LED102
ALARM
W701
1
2
3
4
1-680-065-
11
(11)
1-680-064-
11
(11)
TRANSFORMER BOARD
MAIN BOARD
15 16
10
5
1
20
30
25
BLK RED
WHT L1
AM FERRITE-ROD
ANTENNA
S1
BAND
FM
AM
1
15101517
1
1
2
3
4
3
6
51014
28 JW206
C206
C207
C203
JW205
CN701
252015
IC101
W703
SP1
(SPEAKER)
-2
-1
D203
S2
(Function Selector)
ALARM
BUZZER RADIO RADIO ON OFF
LED101
T2
POWER
TRANSFORMER
PS101
C
BE
AR, SP MODEL
AR, E13, SP MODEL
AR, E13, SP MODEL
E92, MX MODEL
EB
C
AC IN ~
E92, MX MODEL
AR, E13, SP MODEL AR, E13, SP MODEL
TLM1 TLM2
AR, E13, SP MODEL
E92, MX MODEL
D101 F-6
D201 H-9
D202 H-9
D203 D-9
D204 H-5
D205 H-5
IC1 D-5
IC101 H-7
LED101 I-6
LED102 I-2
Q1 G-2
Q201 F-9
(Q202) D-9
•Semiconductor
Location
Ref.No. Location
( ) : E92, MX MODEL

ICF-C111
13 13
5-3. SCHEMATIC DIAGRAM • Refer to page 10 for Common Note on Schematic Diagram and page 14 for IC Block Diagrams.
IC B/D
IC B/D
(Function Selector)
E92, MX MODEL AR, E13, SP MODEL
E92, MX MODEL
AR, E13, SP MODEL
AR, SP MODEL
AR, E13, SP MODEL

ICF-C111
1414
12 3 45 6 7 8 9 10 15141312
11
FM
DISCRIMINATOR
AF POWER AMP AM FE FM IF
TUNING
METER
AM IF DET AGC
FM FE
23 22 21 202425 19 18 17 1629 28 27 2630
GND GND AF OUT +B RIPPLE FILTER AF IN DET OUT AFC (J)AGC AFC (W)AGC IF GND LED NC FM IF IN AM IF IN BAND SW
NC
MIX OUT
FE GND
AM ANT
FM RF
REG
FM OSC
FM ANT
AFC
AM OSC
VOL
NF
DISCRI
GND GND
28 27 26 25 24 23 22 21 20 19 18 17 16 15
1 2 3 4 5 6 7 8 9 10 11 12 13 14
AM & 10,S
HR AG & DE
PM & 10,S HR B
10,S HR C & HR B
10,S MIN A & F
10,S MIN B & G
10,S MIN C & D
MIN A & F
COLON OUTPUT
MIN C & D MIN B & G
10,S MIN E
& MIN E
HR B & G HR C & D
HR A & F
12/24 HR SELECT 50/60 Hz SELECT 50/60 Hz INPUT SLEEP INPUT SNOOZE INPUT CR/INPUT HOUR SET MIN SET ALARM DISP ALARM OFF SLEEP OUT ALARM OUT VDD VSS
D
OSC
CTR
GATE
1/2
1Hz
2Hz
50/60Hz
GATE COMPARATOR SLEEP CTR
OUTPUT DECODER/DRIVER
CONTROL
PWR UP
OUTPUT
CONTROL
DISPLAY
CONTROL
RESET
CONTROL
PF.
DET
SEC
CTR ALARM
MIN CTR
TIME
MIN CTR
TIME
HR CTR
ALARM
HR CTR
BLANK &
FLASH
1/25 or 1/30
STAND
BY DET
D DD D D
INPUT
CONTROL
F.SAMPLE
S.SAMPLE
SLEEP SEC,TIME,ALARM
IC1 CXA1019S
• IC Block Diagrams
IC101 LM8560N

15
ICF-C111
SECTION 6
EXPLODED VIEWS
Ref. No. Part No. Description Remark
6-1. CABINET (UPPER) SECTION
Ref. No. Part No. Description Remark
1 3-226-587-01 KNOB (FUNCTION) (BLACK)
1 3-226-587-11 KNOB (FUNCTION) (WHITE)
2 3-226-584-01 PANEL (FRONT) (E92,MX)
2 3-226-584-11 PANEL (FRONT) (AR,E13,SP)
3 X-3380-019-1 UPPER ASSY, CABINET (BLACK) (E92)
3 X-3380-019-2 UPPER ASSY, CABINET (WHITE) (E92,MX)
3 X-3380-020-1 UPPER ASSY, CABINET (BLACK) (AR,E13,SP)
3 X-3380-020-2 UPPER ASSY, CABINET (WHITE) (AR,SP)
4 7-685-647-79 SCREW +P 3X10 TYPE2 NON-SLIT
05 1-555-795-00 CORD, POWER (E13,SP)
05 1-769-339-22 CORD, POWER (E92,MX)
05 1-790-124-11 CORD, POWER (AR)
6 7-685-153-19 SCREW +P 3X30 TYPE2 NON-SLIT
7 3-368-852-01 FOOT
8 3-369-135-21 LID, BATTERY CASE
9 3-515-102-31 CUSHION
NOTE:
• The mechanical parts with no reference
number in the exploded views are not supplied.
• Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.
• Abbreviation
AR : Argentina model
E13 : AC 220 – 230 V area in E model
E92 : AC 120V area in E model
MX : Mexican model
SP : Singapore model
• Color Indication of Appearance Parts
Example :
KNOB, BALANCE (WHITE) ... (RED)
Parts Color Cabinet’s Color
• Accessories and packing materials are
given in the last of this parts list.
RR
The components identified by
mark 0or dotted line with mark
0are critical for safety.
Replace only with part number
specified.
4
2
3
9
1
5
6
7
8
6

16
ICF-C111
6-2. CABINET (LOWER) SECTION
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
51 3-226-583-01 CABINET (LOWER) (BLACK) (E92)
51 3-226-583-11 CABINET (LOWER) (WHITE) (E92,MX)
51 3-226-583-21 CABINET (LOWER) (BLACK) (AR,E13,SP)
51 3-226-583-31 CABINET (LOWER) (WHITE) (AR,SP)
*52 1-680-065-11 TRANSFORMER BOARD
53 1-535-804-21 SNAP, BATTERY
54 7-685-647-79 SCREW +P 3X10 TYPE2 NON-SLIT
*55 A-3052-458-A MAIN BOARD COMPLETE (E13)
*55 A-3683-274-A MAIN BOARD COMPLETE (E92,MX)
*55 A-3683-279-A MAIN BOARD COMPLETE (AR,SP)
56 3-226-590-01 HOLDER (ANTENNA)
57 3-933-547-01 SHEET (BAND)
58 3-226-588-01 KNOB (TUNING) (BLACK)
58 3-226-588-11 KNOB (TUNING) (WHITE)
59 3-226-589-01 POINTER
60 3-919-268-01 KNOB (VOL) (BLACK)
60 3-919-268-11 KNOB (VOL) (WHITE)
61 3-226-585-01 CHASSIS
62 3-553-567-00 CUSHION
63 1-754-135-11 ANTENNA (WIRE)
LED101 8-749-016-86 LED SL-3998-78T (E92,MX)
LED101 8-749-016-87 LED SL-3998-79T (AR,E13,SP)
SP1 1-529-456-11 SPEAKER (6.6cm)
0T2 1-433-573-11 TRANSFORMER, POWER (E92,MX)
0T2 1-433-574-21 TRANSFORMER, POWER (AR,E13,SP)
W703 1-757-686-11 CORD, CONNECTION (17 CORE)
The components identified by
mark 0or dotted line with mark
0are critical for safety.
Replace only with part number
specified.
51
52 62
SP1
L1
T2
LED101
W703
not supplied
53
54 54 55
57
63
56
54
58
59
60
61
54

17
ICF-C111
SECTION 7
ELECTRICAL PARTS LIST
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
*A-3052-458-A MAIN BOARD, COMPLETE (E13)
*A-3683-274-A MAIN BOARD, COMPLETE (E92,MX)
*A-3683-279-A MAIN BOARD, COMPLETE (AR,SP)
*********************
1-535-804-21 SNAP, BATTERY
1-754-135-11 ANTENNA (WIRE)
3-226-590-01 HOLDER (ANTENNA)
7-685-647-79 SCREW +P 3X10 TYPE2 NON-SLIT
< BPF >
BPF1 1-236-022-11 FILTER, BAND PASS
< CAPACITOR >
C1 1-162-936-11 CERAMIC CHIP 5PF 0.25PF 50V
C2 1-164-160-11 CERAMIC CHIP 20PF 5% 50V
C3 1-164-405-11 CERAMIC CHIP 27PF 5% 50V
C5 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C6 1-104-664-11 ELECT 47uF 20% 10V
C7 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C8 1-126-960-11 ELECT 1uF 20% 50V
C9 1-126-963-11 ELECT 4.7uF 20% 50V
C10 1-126-964-11 ELECT 10uF 20% 50V
C11 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
C12 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C13 1-126-964-11 ELECT 10uF 20% 50V
C14 1-109-982-11 CERAMIC CHIP 1uF 10% 10V
C15 1-126-924-11 ELECT 330uF 20% 10V
C16 1-109-982-11 CERAMIC CHIP 1uF 10% 10V
C18 1-104-665-11 ELECT 100uF 20% 10V
C19 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C20 1-162-907-11 CERAMIC CHIP 2PF 0.25PF 50V
C101 1-162-969-11 CERAMIC CHIP 0.0068uF 10% 25V
C102 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C103 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C104 1-164-361-11 CERAMIC CHIP 0.047uF 16V
C107 1-126-961-11 ELECT 2.2uF 20% 50V
C201 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C202 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C203 1-126-934-11 ELECT 220uF 20% 16V
C204 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C205 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C206 1-126-935-11 ELECT 470uF 20% 10V
C207 1-126-935-11 ELECT 470uF 20% 10V
C210 1-126-933-11 ELECT 100uF 20% 16V
< FILTER >
CF1 1-781-861-71 FILTER, CERAMIC (COMBINATION)
CF2 1-781-790-11 FILTER, AM CERAMIC
CF3 1-781-861-71 FILTER, CERAMIC (COMBINATION)
< CONNECTOR >
*CN701 1-568-272-11 SOCKET, CONNECTOR 6P
< VARIABLE CAPACITOR >
CT1-4 1-141-522-11 CAP, VAR
CV1 1-141-522-11 CAP, VAR (TUNING)
< DIODE >
D101 8-719-911-19 DIODE 1SS119-25
D201 8-719-911-19 DIODE 1SS119-25
D202 8-719-052-88 DIODE 1N4002
D203 8-719-911-19 DIODE 1SS119-25
D204 8-719-911-19 DIODE 1SS119-25
D205 8-719-911-19 DIODE 1SS119-25
< IC >
IC1 8-752-037-02 IC CXA1019S
IC101 8-759-821-46 IC LM8560N
< JUMPER RESISTOR >
JC101 1-216-864-11 SHORT 0 (AR,SP)
JC102 1-216-864-11 SHORT 0 (AR,E13,SP)
JC103 1-216-864-11 SHORT 0 (AR,E13,SP)
JC105 1-216-864-11 SHORT 0
< COIL >
L1 1-419-532-11 COIL, FERRITE-ROD ANTENNA (AM)
L2 1-419-533-11 COIL, OSCILLATION (AM)
*L3 1-422-320-11 COIL, AIR-CORE
L4 1-422-131-00 COIL, FM OSCILLATION
< DIODE >
LED101 8-749-016-86 LED SL-3998-78T (E92,MX)
LED101 8-749-016-87 LED SL-3998-79T (AR,E13,SP)
LED102 8-719-054-61 LED SLR-342VRTJ7 (ALARM)
< TRANSISTOR >
Q1 8-729-216-22 TRANSISTOR 2SA1162-G
NOTE:
• Due to standardization, replacements in
the parts list may be different from the
parts specified in the diagrams or the
components used on the set.
• RESISTORS
All resistors are in ohms.
METAL:Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F:nonflammable
• Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.
• SEMICONDUCTORS
In each case, u : µ, for example:
uA.. : µA.. uPA.. : µPA..
uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD..
• CAPACITORS
uF : µF
• COILS
uH : µH
The components identified by
mark 0or dotted line with mark
0are critical for safety.
Replace only with part number
specified.
When indicating parts by reference
number, please include the board.
• Abbreviation
AR : Argentina model
E13 :AC 220 – 230V area in E model
E92 : AC 120V area in E model
MX : Mexican model
SP : Singapore model
MAIN

18
ICF-C111
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
Q201 8-729-011-92 TRANSISTOR 2SC2001TP-K1K2
Q202 8-729-216-22 TRANSISTOR 2SA1162-G (E92,MX)
< RESISTOR >
R1 1-216-815-11 METAL CHIP 330 5% 1/16W
R2 1-216-805-11 METAL CHIP 47 5% 1/16W
R4 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R5 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R6 1-216-821-11 METAL CHIP 1K 5% 1/16W
R101 1-216-849-11 METAL CHIP 220K 5% 1/16W
R102 1-216-845-11 METAL CHIP 100K 5% 1/16W
R103 1-216-845-11 METAL CHIP 100K 5% 1/16W
R104 1-216-841-11 METAL CHIP 47K 5% 1/16W
R105 1-216-835-11 METAL CHIP 15K 5% 1/16W
R106 1-216-815-11 METAL CHIP 330 5% 1/16W
R107 1-216-832-11 METAL CHIP 8.2K 5% 1/16W
R204 1-216-801-11 METAL CHIP 22 5% 1/16W
R205 1-216-821-11 METAL CHIP 1K 5% 1/16W
R206 1-249-409-11 CARBON 220 5% 1/4W
R209 1-249-389-11 CARBON 4.7 5% 1/4W
R210 1-249-389-11 CARBON 4.7 5% 1/4W
R212 1-216-833-11 METAL CHIP 10K 5% 1/16W
R213 1-216-833-11 METAL CHIP 10K 5% 1/16W
R214 1-216-833-11 METAL CHIP 10K 5% 1/16W
< SWITCH >
S1 1-692-181-21 SWITCH, SLIDE (BAND)
S2 1-771-904-11 SWITCH, SLIDE (Function selector)
S3 1-692-014-11 SWITCH, KEYBOARD (TIME SET M)
S4 1-692-014-11 SWITCH, KEYBOARD (TIME SET H)
S5 1-692-014-11 SWITCH, KEYBOARD (ALARM)
S6 1-692-014-11 SWITCH, KEYBOARD (CLOCK)
S7 1-692-014-11 SWITCH, KEYBOARD (SLEEP)
S8 1-692-014-11 SWITCH, KEYBOARD (SNOOZE/SLEEP OFF)
< TRANSFORMER >
T1 1-435-399-11 TRANSFORMER, IF
< VARIABLE RESISTOR >
VR1 1-228-790-00 RES, VAR, CARBON 50K (VOLUME)
< CONNECTION CORD >
W703 1-757-686-11 CORD, CONNECTION (17 CORE)
*************************************************************
*1-680-065-11 TRANSFORMER BOARD
********************
01-555-795-00 CORD, POWER (E13,SP)
01-769-339-22 CORD, POWER (E92,MX)
01-790-124-11 CORD, POWER (AR)
< IC LINK >
0PS101 1-533-971-11 LINK, IC (200mA) (AR,E13,SP)
< TRANSFORMER >
0T2 1-433-573-11 TRANSFORMER, POWER (E92,MX)
0T2 1-433-574-21 TRANSFORMER, POWER (AR,E13,SP)
< TERMINAL >
*TLM1 1-535-771-11 TERMINAL (AR,E13,SP)
*TLM2 1-535-771-11 TERMINAL (AR,E13,SP)
*************************************************************
MISCELLANEOUS
***************
05 1-555-795-00 CORD, POWER (E13,SP)
05 1-769-339-22 CORD, POWER (E92,MX)
05 1-790-124-11 CORD, POWER (AR)
53 1-535-804-21 SNAP, BATTERY
SP1 1-529-456-11 SPEAKER (6.6cm)
*************************************************************
ACCESSORIES & PACKING MATERIALS
********************************
3-227-320-01 SHEET (BLIND) (BLACK) (E92)
3-227-320-11 SHEET (BLIND) (WHITE) (E92,MX)
3-227-587-11 MANUAL, INSTRUCTION (ENGLISH,FRENCH,
GERMAN,SPANISH,DUTCH,ITALIAN)
(AR,E13,E92,MX)
3-227-587-41 MANUAL, INSTRUCTION (ENGLISH,
SIMPLIFIED CHINESE,POLISH,CZECH,
HUNGARIAN,SLOVAKIAN) (SP)
The components identified by
mark 0or dotted line with mark
0are critical for safety.
Replace only with part number
specified.
TRANSFORMERMAIN

19
ICF-C111
MEMO

20
ICF-C111
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.
Ver. Date Description of Revision
1.1 2001. 05 AR, E13 and MX model has been added.
1.0 2001. 03 New