
Information in this document is subject to 
change without notice.
Sony, VAIO and CLIE are trademarks or regis-
tered trademarks of Sony. Microsoft, Windows, 
Windows Media, Outlook, Bookshelf and other 
Microsoft products are trademarks or registered 
trademarks of Microsoft Corporation in the 
United States and other countries. The word 
Bluetooth and the Bluetooth logo are trademarks 
of Bluetooth SIG, Inc.AMD, the AMD logo, other 
AMD product names and combinations thereof 
are trademarks of Advanced Micro Devices, Inc. 
IntelInside logo, Pentium, Celeron and Core are 
trademarks or registered trademarks of IntelCor-
poration. Transmeta, the Transmeta logo, Crusoe 
Processor, the Crusoe logo and combinations 
thereof are trademarks of Transmeta Corporation 
in the USA and other countries. Graffiti, Hot-
Sync, PalmModem, and Palm OSare registered 
trademarks, and the Hotsync logo and Palm are 
trademarks of Palm, Inc. or its subsidiaries. (M) 
and Motrola are trademarks of Motrora, Inc. Other 
Motrola products and services with (R) mark like
Dragomball are the trademarks of Motrola, Inc.
All other names of systems, products and services 
in this manualare trademarks or registered trade-
marks of their respective owners. In this manual,
the (TM) or (R) mark are not specified.
Caution Markings for Lithium/Ion Battery- The 
following or similar texts shall be provided on 
batterypack of equipment or in both the operating 
and the service instructions.
CAUTION: Danger of explosion if batteryis 
incorrectly replaced. Replace only with the same 
or equivalent type recommended bythe manu-
facturer. Discard used batteries according to the 
manufacturer’s instructions.
CAUTION: The batterypack used in this device 
maypresent a fire or chemicalburn hazard if mis-
treated. Do not disassemble, heat above 60°C
(140°F) or incinerate. Dispose of used battery
promptly. Keep awayfrom children.
CAUTION: Changing the back up battery.
•Overcharging, short circuiting, reverse charg-
ing, multilation or incineration of the cells must 
be avoided to prevent one or more of the fol-
lowing occurrences; release of toxic materials,
release of hydrogen and/or oxygen gas, rise in 
surface temperature.
•If a cell has leaked or vented, it should be 
replaced immediately while avoiding to touch 
it without anyprotection.
Serviceand Inspection Precautions
1. Obey precautionary markings and
instructions
Labels and stamps on the cabinet, chassis, and 
components identifyareas requiring specialpre-
cautions. Be sure to observe these precautions, 
as well as all precautions listed in the operating 
manualand other associated documents.
2. Use designated parts only
The set’s components possess important safety
characteristics, such as noncombustibilityand 
the abilityto tolerate large voltages. Be sure that 
replacement parts possess the same safetycharac-
teristics as the originals. Also remember that the 
 mark, which appears in circuit diagrams and 
parts lists, denotes components that have particu-
larly important safetyfunctions; be extra sure to 
use only the designated components.
3. Always follow the original design 
when mounting parts and routing 
wires
The originallayout includes various safetyfea-
tures, such as inclusion of insulating materials
(tubes and tape) and the mounting of parts above 
the printer board. In addition, internalwiring has 
been routed and clamped so as to keep it away
from hot or high-voltage parts. When mounting 
parts or routing wires, therefore, be sure to du-
plicate the originallayout.
4. Inspectafter completing service
After servicing, inspect to make sure that all
screws, components, and wiring have been 
returned to their originalcondition. Also check 
the area around the repair location to ensure that 
repair work has caused no damage, and confirm 
safety.
5. When replacing chip components...
Never reuse components. Also remember that 
the negative side of tantalum capacitors is easily
damaged byheat.
6. When handling flexible print 
boards...
•The temperature of the soldering-iron tip 
should be about 270°C.
•Do not apply the tip more than three times to 
the same pattern.
•Handle patterns with care; never apply force.
Caution: Remember that hard disk drives are 
easily damaged byvibration. Always handle
with care.
2[Sony Confidential] 
VGN-AW Series (9-852-817-XX)
7KHFRPSRQHQWVLGHQWLILHGE\PDUN FRQWDLQ
FRQ¿GHQWLDOLQIRUPDWLRQ
6WULFWO\IROORZWKHLQVWUXFWLRQVZKHQHYHUWKH
FRPSRQHQWVDUHUHSDLUHGDQGRUUHSODFHG