Sony VAIO PCGA-PRF1 User manual

9-974-497-11
PCGA-PRF1 (UC/AEP/UK)
– 24 –
Sony Corporation
xxx
PCGA-PRF1
Port Replicator
9-974-497-11
PCGA-PRF1 (UC/AEP/UK) 9-974-497-11 99x16xx-1
English
99x16xx-1
Printed in xxx
© 1999. x
xxx
US Model
Canadian Model
AEP Model
UK Model
Specifications
ox.
Connectors SERIAL Connector, RS-232C, D-
SUB 9 pin (1)
PRINTER Connector, ECP, D-
SUB 25 pin (1)
MONITOR Connector, analog
RGB, mini D-SUB 15 pin (1)
USB Connector, USB 4 pin (1)
NETWORK Connector,
10BASE-T (1)
MOUSE/KEYBOARD
Connector, PS/2, mini DIN 6
pin (2)
Operating temperature
41°Fto95°F(5°Cto35°C)
Dimensions Approx. 12
7
/ 8 ×1
11
/ 16 ×4
3
/ 8
inches (w/h/d)
(Appr 324 ×42 ×109 mm)
Mass 470 g (14.3 oz.)
Supplied accessory
Operating instructions (1)
Design and specifications are subject to change
without notice.

Information in this document is subject to change without
notice.
Sony and VAIO are trademarks of Sony. Intel logo and Intel
Inside logo are registered trademarks of Intel Corporation.
Pentium MMX is a trademark of Intel Corporation. Microsoft,
MS-DOS, Windows, the Windows 95 and Windows 98 logo
are trademarks of Microsoft Corporation.
All other trademarks are trademarks or registered trademarks
of their respective owners. Other trademarks and trade names
may be used in this document to refer to the entitles claiming
the marks and names or their produces. Sony Corporation
disclaimsanyproprietaryinterest intrademarks andtrade names
other than its own.
Service and Inspection Precautions
1. Obey precautionary markings and
instructions
Labels and stamps on the cabinet, chassis, and components identify
areas requiring special precautions. Be sure to observe these
precautions, as well as all precautions listed in the operating manual
and other associated documents.
2. Use designated parts only
The set’s components possess important safety characteristics, such
as noncombustibility and the ability to tolerate large voltages. Be
sure that replacement parts possess the same safety characteristics as
the originals. Also remember that the !mark, which appears in
circuit diagrams and parts lists, denotes components that have
particularly important safety functions; be extra sure to use only the
designated components.
3. Always follow the original design when
mounting parts and routing wires
The original layout includes various safety features, such as inclusion
of insulating materials (tubes and tape) and the mounting of parts
above the printer board. In addition, internal wiring has been routed
and clamped so as to keep it away from hot or high-voltage parts.
When mounting parts or routing wires, therefore, be sure to duplicate
the original layout.
4. Inspect after completing service
After servicing, inspect to make sure that all screws, components,
and wiring have been returned to their original condition. Also check
theareaaroundtherepairlocationtoensurethatrepair work has caused
no damage, and confirm safety.
5. When replacing chip components...
Never reuse components. Also remember that the negative side of
tantalum capacitors is easily damaged by heat.
6. When handling flexible print boards...
•The temperature of the soldering-iron tip should be about 270C.
•Do not apply the tip more than three times to the same pattern.
•Handle patterns with care; never apply force.
Caution: Remember that hard disk drives are easily damaged by
vibration. Always handle with care.
– 2 –
Caution Markings for Lithium/Ion Battery - The following or
similar texts shall be provided on battery pack of equipment or
in both the operating and the service instructions.
CAUTION: Danger of explosion if battery is incorrectly
replaced. Replace only with the same or equivalent type
recommended by the manufacturer. Discard used batteries
according to the manufacturer’s instructions.
CAUTION: The battery pack used in this device may present a
fire or chemical burn hazard if mistreated. Do not disassemble,
heat above 100°C (212°F) or incinerate.
Dispose of used battery promptly.
Keep away from children.
PCGA-PRF1 (UC/AEP/UK)
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE !SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

– 3 – PCGA-PRF1 (UC/AEP/UK)
TABLE OF CONTENTS
CHAPTER 1. OPERATION
1-1. Operating Instructions ..................................................... 1-1
(to 1-3)
CHAPTER 2. REMOVAL
2-1. Flowchart ......................................................................... 2-1
2-2. Assy Bottom .................................................................... 2-1
2-3. CNX-61 Board, Panel, CONN APR ................................ 2-2
(to 2-2)
CHAPTER 3. SELF DIAGNOSTICS
3-1. Required Tools and Peripheral Devices ........................... 3-1
3-2. Tools and Peripheral Device Connection......................... 3-3
3-3. How to Start the Disk-Based Diagnostics........................ 3-4
(to 3-4)
CHAPTER 4. BLOCK DIAGRAM ......................... 4-1
(to 4-2)
CHAPTER 5. EXPLODED VIEWS AND
PARTS LIST ................................... 5-1
(to 5-2)
Section Title Page
• Abbreviations
UC : US model / Canadian model

1-1 PCGA-PRF1 (UC/AEP/UK)
CHAPTER 1.
OPERATION
1-1. Operating Instructions (Extracted from 3-865-988-01 (1))
°
English
Port Replicator
Operating Instructions
Warning
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
To avoid electrical shock, do not open
the cabinet. Refer servicing to qualified
personnel only.
Owner’s Record
The model number and serial number are located on
the bottom of your port replicator. Record the serial
number in the space provided here. Refer to the model
and serial number when you call your Sony Service
Center.
Model No. PCGA-PRF1
Serial No. ___________________
This product conforms with the following
European Directives:
73/23/EEC (LowVoltage Directive)
89/336/EEC, 92/31/EEC (EMC Directive)
93/68/EEC (CE-Marking Directive)
This equipment complies with EN55022 Class B
and EN50082-1 for use in the following areas:
residential, business, and light-industrial.
This equipment has been tested and found to
comply with the limits set out in the EMC
Directive using a connection cable shorter than
3 meters (9.8 feet).
Before use
Before using the port replicator, please read this
manual thoroughly and retain it for future
reference. See also the VAIO Notebook Computer
User Guide for more information.
The Sony PCGA-PRF1 is the port replicator
designed for a Sony Notebook Computer PCG-
F100 series.
It cannot be used with any other computer.
PCGA-PRF1
Specifications
Connectors SERIAL Connector, RS-232C, D-
SUB 9 pin (1)
PRINTER Connector, ECP, D-
SUB 25 pin (1)
MONITOR Connector, analog
RGB, mini D-SUB 15 pin (1)
USB Connector, USB 4 pin (1)
NETWORK Connector,
10BASE-T (1)
MOUSE/KEYBOARD
Connector, PS/2, mini DIN 6
pin (2)
Operating temperature
41°Fto95°F(5°Cto35C)
Dimensions Approx. 12
7
/ 8 ×1
11
/ 16 ×4
3
/ 8
inches (w/h/d)
(Approx. 324 ×42 ×109 mm)
Mass 470 g (14.3 oz.)
Supplied accessory
Operating instructions (1)
Design and specifications are subject to change
without notice.
Notes on use
• Do not place the unit in locations that are:
– Extremely hot or cold
– Dusty or dirty
– Very humid
– Vibrating
– Subject to strong magnetic fields
– Sandy
– Subject to direct sunlight
• Do not apply mechanical shock or drop the
unit.
• Be sure that nothing metallic comes into
contact with the metal parts of this unit. If
this happens, a short-circuit may occur and
the unit may be damaged.
• Do not operate the unit with a damaged
cord or if it has been dropped or damaged.
• Always keep the metal contacts clean.
• Do not disassemble or convert the unit.
• While the unit is in use, it gets warm; this is
normal.
• Keep the unit away from TV or AM
receivers, because it can disturb TV or AM
reception.
On cleaning
Clean the unit with a soft dry cloth, or a soft
cloth lightly moistened with a mild detergent
solution. Do not use any type of solvent, such
as alcohol or benzine, which may damage the
finish.

1-2PCGA-PRF1 (UC/AEP/UK)
à
Français
Port Replicator
Mode d’emploi
Avertissement
Pour prévenir tout risque d’incendie ou
d’électrocution, garder cet appareil à
l’abri de la pluie et de l’humidité.
Pour prévenir tout risque
d’électrocution, ne pas ouvrir le boîtier.
Confier l’entretien de cet appareil
exclusivement au personnel qualifié.
Ce produit est conforme aux directives
européennes suivantes:
73/23/CEE (Basse tension)
89/336/CEE, 92/31/CEE (Directives CEM)
93/68/CEE (Marquage CE)
Cet équipement est conforme aux normes
EN55022 Classe B et EN50082-1, limitant
l’emploi dans les environnements résidentiel,
professionnel et industriel léger.
Cet appareil a été testé et déclaré conforme aux
limites de la Directive EMC lors de l’utilisation
d’un câble de liaison de moins de 3 mètres.
Avant utilisation
Avant d’utiliser cet réplicateur de port, lisez
attentivement le présent mode d’emploi et
conservez-le pour toute référence ultérieure.
Consultez également le Manual d’utilisation de
ordinateur bloc-notes VAIO.
Le PCGA-PRF1 Sony est le réplicateur de port
conçu pour un ordinateur bloc-notes Sony série
PCG-F100.
Il ne peut être utilisé avec un autre ordinateur.
PCGA-PRF1
Spécifications
Connecteurs Série (SERIAL), RS-232C, D-
SUBà9broches (1)
Imprimante (PRINTER), ECP,
D-SUB à 25 broches (1)
Moniteur (MONITOR), RVB
analogique, miniconnecteur D-
SUB à 15 broches (1)
USB, USBà4broches (1)
Réseau (NETWORK),
10BASE-T (1)
Souris/Clavier (MOUSE/
KEYBOARD), PS/2,
miniconnecteur DIN à 6
broches (2)
Température d’utilisation
5°C35°C (41 °Fà95°F)
Dimensions Approx. 324 ×42 ×109 mm
(l/h/p)
(Approx. 12
7
/ 8 ×1
11
/ 16 ×4
3
/ 8
po.)
Masse Approx. 470g (14.3 li.)
Accessoire fourni
Mode d’emploi (1)
La conception et les spécifications sont sujettes
à modifications sans préavis.
Remarques sur
l’utilisation
• Ne placez pas l’appareil dans des endroits :
– extrêmement chauds ou froids;
– poussiéreux ou sales;
– très humides;
– soumis à des vibrations;
– soumis à de puissants champs
magnétiques;
– sablonneux;
– exposés au rayonnement direct du soleil.
• Ne soumettez pas l’appareil à des chocs
mécaniques et ne le laissez pas tomber.
• Veillez à ce qu’aucun objet métallique
n’entre en contact avec les parties
métalliques de cet appareil. Si cela se
produit, un court-circuit risque de survenir
et d’endommager l’appareil.
• Ne faites pas fonctionner l’appareil avec un
câble endommagé ou s’il est tombé et a subi
des dommages.
• Veillez à ce que les contacts métalliques
restent toujours propres.
• Ne démontez pas et ne transformez pas
l’appareil.
• Le système chauffe en cours d’utilisation.
C’est normal.
• Gardez l’appareil à l’écart des téléviseurs et
des récepteurs AM, il peut causer des
interférences dans la réception télévisée ou
radiophonique.
Entretien
Nettoyez l’appareil au moyen d’un chiffon sec
et doux, ou légèrement imprégné d’une
solution détergente neutre. N’utilisez aucun
type de solvant, comme de l’alcool ou de la
benzine, qui risquerait de ternir le fini de
l’appareil.

1-3 PCGA-PRF1 (UC/AEP/UK)
(END)
Deutsch
Port Replicator
Bedienungsanleitung
Achtung
Um Feuergefahr und die Gefahr eines
elektrischen Schlags zu vermeiden,
setzen Sie das Gerät weder Regen noch
sonstiger Feuchtigkeit aus.
Um einen elektrischen Schlag zu
vermeiden, öffnen Sie das Gehäuse
nicht. Überlassen Sie Wartungsarbeiten
stets nur qualifiziertem Fachpersonal.
Richtlinien: Dieses Gerät erfüllt die 73/23/
EEC (Niederspannugsrichtlinie)
89/336/EEC und 92/31/EEC
(EMV Richtlinien)
93/68/EEC (CE Zeichen)
Dieses Gerät erfüllt die Standards EN55022
Class B und EN50082-1 für folgende Gebiete:
• Wohngebiete
• Gewerbegebiete
• Leichtindustriegebiete
Anhand von Tests wurde sichergestellt, daß
dieses Gerät auch bei einem Anschlußkabel, das
kürzer als 3 m ist, die EMC-Richtlinien erfüllt.
Vorbereitung
Lesen Sie diese Anleitung vor der
Inbetriebnahme des Port-Replikators bitte
genau durch, und bewahren Sie sie zum
späteren Nachschlagen sorgfältig auf.
Informieren Sie sich bitte auch im
Benutzerhandbuch zum Notebook-Computer von
VAIO nach.
Der PCGA-PRF1 von Sony ist ein Port-
Replikator für Notebook-Computer Serie PCG-
F100 von Sony.
Er eignet sich nicht für andere Computer.
PCGA-PRF1
Technische Daten
Anschlüsse Serieller Anschluß SERIAL, RS-
232C, D-SUB, 9polig (1)
Druckeranschluß PRINTER,
ECP, D-SUB, 25polig (1)
Monitoranschluß MONITOR,
RGB, analog, Mini-D-SUB,
15polig (1)
USB Anschluß, USB, 4polig (1)
Netzwerkanschluß NETWORK,
10BASE-T (1)
Maus/Tastatur Anschluß
MOUSE/KEYBOARD, PS/2,
Mini-DIN, 6polig (2)
Betriebstemperatur
5°C bis 35 °C
Abmessungen ca. 324 ×42 ×109 mm (B/H/T)
Gewicht ca. 470 g
Mitgeliefertes Zubehör
Bedienungsanleitung (1)
Irrtümer und technische Änderungen
vorbehalten.
Hinweise zur
Verwendung
• Stellen Sie das Gerät nicht an einen Ort, an
dem es folgenden Bedingungen ausgesetzt
ist:
– extremen Temperaturen
– Staub oder Schmutz
– hoher Luftfeuchtigkeit
– Vibrationen
– starken Magnetfeldern
– Sand
– direktem Sonnenlicht
• Setzen Sie das Gerät keinen mechanischen
Erschütterungen aus, und lassen Sie es nicht
fallen.
• Achten Sie darauf, daß keine
Metallgegenstände mit den Metallteilen
dieses Geräts in Berührung kommen.
Andernfalls kann es zu einem Kurzschluß
kommen, und das Gerät könnte beschädigt
werden.
• Verwenden Sie das Gerät nicht, wenn das
Kabel oder das Gerät selbst beschädigt oder
das Gerät fallengelassen wurde.
• Halten Sie die Metallkontakte sauber.
• Zerlegen Sie das Gerät nicht, und nehmen
Sie keine Veränderungen daran vor.
• Das Gerät erwärmt sich während des
Betriebs. Das ist normal.
• Halten Sie das Gerät von Fernseh- oder AM-
Empfängern fern. Der Empfang kann gestört
werden.
Reinigung
Reinigen Sie das Gerät mit einem weichen,
trockenen Tuch oder einem weichen Tuch, das
Sie leicht mit einem milden Reinigungsmittel
angefeuchtet haben. Verwenden Sie keine
Lösungsmittel wie Alkohol oder Benzin, da dies
zu Beschädigungen der Oberfläche führen
kann.

2-1 PCGA-PRF1 (UC/AEP/UK)
CHAPTER 2.
REMOVAL
2-1. Flowchart
• P XX means pages that appears in this manual.
2-2. Assy Bottom
ASSY
BOTTOM
P 2-1
PANEL, CONN
APR
P 2-2
CNX-61
BOARD
P 2-2
(B2), Tapping, P3 (X5)
1

(B2), Tapping, P3 (X3)
Assy Bottom
Upper APR Assy
1


2-2PCGA-PRF1 (UC/AEP/UK)
2-3. CNX-61 Board, Panel, CONN APR
(END)
2+B 2.6X8
2+B 2.6X8
7+B 2.6X8 (X2)
3+B 2.6X8
(X2)
6
1+B 2X3
5(X6)
4(B2), Tapping, P3
Upper APR Assy
Panel, CONN APR
CNX-61 Complete PWB
4(B2), Tapping, P3
2+B 2.6X8
(X6)

3-1 PCGA-PRF1 (UC/AEP/UK)
CHAPTER 3.
SELF DIAGNOSTICS
3-1. RequiredTools and Peripheral Devices
Tools and Peripheral Devices
1 Serial Loopback Tool
Loopback Tool specified by QA and Factory
(Refer to next page.)
2 Parallel Loopback Tool
Loopback Tool specified by QA and Factory
(Refer to next page.)
3 USB Tester
USB Host Production Tester
Made by Computer Access Technology Corp.
4 PCG-F1 Series
5 FDD Bay
6 Diagnostics FD Media
7 Diagnostics CD-ROM Media
8 AC Adaptor
Test Items
Serial Port (COM) test
Parallel Port (Printer) test
USB Device test
(For Diagnostics)
FDD test
(Diagnostics starting software)
(Diagnostics software)
(Power supply for diagnostics)

3-2PCGA-PRF1 (UC/AEP/UK)
1
2
3
4
5
6
7
8
9
DB9S
DCD
RX
TX
DTR
GND
DSR
RTS
CTS
RI
• Connector Types DB9S (Females)
• Interface Standard RS-232C
• Loopback Data & Handshake
SERIAL LOOPBACK CONNECTOR CONNECTION DIAGRAM
• Connector Types DB25P(Males)
• Interface Standard Centronics
• Loopback Status to Commands
PARALLEL LOOPBACK CONNECTOR CONNECTION DIAGRAM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
D0
D1
D2
D3
D4
D5
D6
D7
-ACK
BUSY
PE
SLCT
-STROBE -AUTO FD
-ERROR
-INT
-SLCT IN
GND
GND
GND
GND
GND
GND
GND
GND
DB25P
Serial Loopback Tool : For diagnostics of serial port
Parallel Loopback Tool : For diagnostics of parallel port
• The serial loopback tool and the parallel loopback tool are necessary for diagnostics of the serial communication line and
the parallel communication line. Fabricate the serial loopback tool and the parallel loopback tool locally referring to the
connection diagrams shown below.
[Reference] On Serial/Parallel LoopbackTool
NOTE: The black round mark "r" indicates soldering.
NOTE: The black round mark "r" indicates soldering.

3-3 PCGA-PRF1 (UC/AEP/UK)
3-2. Tools and Peripheral Device Connection
System Connection Diagram
2Parallel loopback
tool 1Serial loopback tool
Parallel output
7Diagnostics
CD-ROM media
Port Replicator PCGA-PRF1
USB connector 3USB tester
Serial output
4PCG-F1 series 5FDD bay 6Diagnostics
FD media
8AC adaptor
Battery

3-4PCGA-PRF1 (UC/AEP/UK)
3-3. How to Start the Disk-Based Diagnostics
1. Insert a diagnostics FD disk media into the FDD bay and turn on the main power of the computer to boot the computer from
a diagnostics disk.
2. When the computer starts up, the following message appears.
Insert PCGA-PRF1 Diagnostics CD-ROM
Then insert the diagnostics CD-ROM media into the CD-ROM drive or DVD-ROM drive.
3. The following top menu appears.
PCGA-PRF1 Diagnostics program Version 1.0
Copyright (c) Sony Corporation 1999. All rights reserved.
Top Menu
1. PCGA-PRF1 Diagnostics
2. Exit menu
Select menu:
Each diagnostics can be executed independently from the PCGA-PRF1 Diagnostics.
Select item 2 to exit the self-diagnostics.
(END)

4-2 PCGA-PRF1 (UC/AEP/UK)4-1
CHAPTER 4.
BLOCK DIAGRAM
(END)
On board memory
128Mbit SDRAM x4
(64Mbyte) or
64Mbit SDRAM x4
(32Mbyte)
Primary IDE
RO-7 BOARD
PCI_AD[31:0]
PCI_CTRL
PCI_AD[31:0]
PCI_CTRL
PCI_CLKs
ZV VIDEO
ZV AUDIO
ExtendIO_SA[19:0]
EIO_SD[15:0]
EIO_CTRL
USB
CONN
MASTER
HDD
CARDBUS
RICOH
RB5C478
VGA
DB-15
CONN
PS/2(0,1) x2
VGA DB-15
Serial DB-9 x1
Printer(Paralell)x1
PCGA-PRF1
Port
Replicator
ACCESS BUS
PIIX4E
PCI-ISA BRIDGE
IDE
USB
RTC
48M
OSC
66MHz
CLOCK
GENERATOR
33MHz
EIO_SA[19:0]
EIO_SD[15:0]
EIO_CTRL
PC CARD
SLOT A
PC CARD
SLOT B
VIDEO CONTROLLER
NM2200
USB x1
PIIX4E
PORT 0
PCGA-PRF1 BLOCK DIAGRAM Rev.0.9
PCI_CLKs
FLASH
512Kx8
IrDA
KB CONN
TRACK
PAD
TP
PHONE
OUT
SPKR
ULTRA I/O
FDC37N958FR
SUPER I/O
KBC
w/EC
ROM INTERFACE
FD
PS/2(0)
CONN
Serial
CONN
Printer(Paralell)
CONN
PCI Dev #5
PCI-
1394
CXD19479Q
COMb
LT1237
COMa
MODEM CONN
RJ11
LVDS DRIVER
14.1" TFT / 13.0" HPA
XGA 1024x768
Q-SW
MUX
POWER CONTROL
8Byte
SODIMM
x1
PRIMARY
BATTERY
DC-IN
CONN
BAT CONN
CD-ROM
FDD
Drive0
SECOND
BATTERY
MULTI-PURPOSE BAY
BAT CONN
MEMORY BUS
FAN
ATF_INT
ATF1
LM75
KEYBOARD
CONN
MAIN SYSTEM BOARD
MBX-15 BOARD
INVERTER
PHY
TSB21LV03A
POWER
SUPPLY
&
CHARGER
Secondary IDE
CS[0,1]#
CS[2,3]#
ZV
48M
Osc.
PCI Dev #1
PCI Dev #2
PCI Dev #3
14M Oscillator
SM
530
LCD(Panel)
AB_Gp2
AB_Gp0
AB_Gp1
AB_Gp2
AB_Gp3
AB_Gp3
AB_Gp1
LED
i.Link (4 pin) CONN
AGP/PCI
[DIXON-256K/128K(66MHz FSB &No AGP)]
LCD CONN
NORTH MODULE CONN 280pin
DC-IN
CONN
DIXON-256K 266/300/333/366MHz
Processor Core with 256KB L2 cache
or
DIXON-128K 266/300MHz
Processor Core with 128KB L2 cache
443DX
SYSTEM CONTROLLER
HOST-PCI BRIGE
MEMORY CONTROLLER HOST
DC-DC
CONVERTER
CPU Core/CPU IO
for PCI Dev #0
AB_Gp3
DCLKRD/WR
H-PBGA 24x26 grid array at 615 leads
ATF0
North Module
MPM-12 BOARD
ATF_INT
MIC
IN
SW
DEVICE BAY1 CONN
AKM
AK4542
PPK
Port Connector 132pin
PCI Dev #4
MODEM module
MODEM CHIP
(RH56LD-PCI)
IFX-56 Board
USB <->
Ether
RJ-45
i.LINK
PS/2
LPT1
CONN

PCGA-PRF1 (UC/AEP/UK)5-25-1
CHAPTER 5.
EXPLODED VIEWS AND PARTS LIST
NOTE:
•The mechanical parts with no reference
number in the exploded views are not
supplied.
•Items marked “*” are not stocked since
they are seldom required for routine
service.Some delay should be anticipated
when ordering these items.
Ref.No. Part No. Description
(END)
Ref.No. Part No. Description
6
5
7
8
15
16 9
4
3
2
13
14
20 19
21
20
20
20
21
10
21
22 21
20
20
12
1
11 B1
B1
20
18
17
20
20
24
23
1 A-8056-104-A CNX-61 COMPLETE PWB
2 4-641-015-01 LEVER L APR
3 4-641-037-01 LEVER SPRING L
4 X-4622-078-1 UPPER APR ASSY
5 4-641-020-01 HOOK L APR
6 3-718-233-01 NUT, PLATE
7 4-641-016-01 HOOK R APR
8 4-641-036-01 LEVER SPRING R
9 4-641-014-01 LEVER R APR
10 X-4622-141-1 ASSY BOTTOM
* 11 4-641-033-01 PANEL CONN. APR
12 X-4622-080-1 PIN L ASSY
* 13 4-641-032-01 PLATE HOOK L
14 4-641-035-01 HOOK SPRING L
15 4-641-029-01 POP UP BAR APR
16 4-641-034-01 HOOK SPRING R
* 17 4-641-031-01 PLATE HOOK R
18 X-4622-079-1 PIN R ASSY
19 4-641-494-01 PIN, GUIDE
20 3-719-694-01 SCREW (2.6X8), +B TAPPING (B)
21 3-719-408-11 SCREW (B2), TAPPING, P3
22 4-640-851-01 FOOT FRONT
* 23 4-635-966-01 SCREW (HEX)
24 4-641-660-01 CAUTION LABEL
B1 7-621-772-08 SCREW +B 2X3
ACCESSORIES & PACKING MATERIALS
*******************************
3-865-988-01 MANUAL, INSTRUCTION