Sony SAT-HD300 - High Definition Satellite... User manual

SONY:
4-097-333-21
t!'I~;fl:lfl"~IilI'ti;nlllg~1J.I~!If(~t~
·········lIlJDliReeeiie,.·········
Operatil1g.··.1il$tryctiollS
©2003 Sony Electronics.
Reproduction in whole or in part without written
permission is prohibited. All rights reserved. SAT-HD300

A
WARNING:
TO REDUCE THE RISK OF ELECTRONIC SHOCK DO NOT REMOVE COVER (OR BACK)
NO USER SERVICEABLE PARTS INSIDE.
REFER TO QUALIFIED SERVICE PERSONNEL.
THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE USER
TO THE PRESENCE OF UNINSULATED "DANGEROUS VOLTAGE" WITHIN THE PRODUCT'S ENCLOSURE THAT MAY BE OF SUFFI-
CIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.
THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPOR-
TANT OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE.
WARNING
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
This product must not be exposed to dripping or splashing liquids. Objects filled with liquids, such as a vase, must not be placed on or above
the product.
NOTE TO CABLE/TV/SATELLITE DISH INSTALLER:
This reminder is provided to call the cable TV system/satellite dish installer's attention to Article 820-40 of the National Electric Code (U.S.A.).
The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding sys-
tem of the building, as close to the point of the cable entry as practical.
REGULATORY INFORMATION: FCC PART 15
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manu-
al, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the inter-
ference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

REGULATORY INFORMATION: FCC Part 68
Sony must make any necessary repairs to the modem portion of this equipment in order to maintain valid FCC registration. Do not attempt to
repair or service the modem.
This equipment cannot be used on public coin service provided by the Telephone Corvpany. Connection to Party Line Service is subject to state
tariffs.
• This product complies with Part 68 of the FCC rules. On the back of this product is a label that contains, among other information, the FCC
registration number and Ringer Equivalent Number (REN) for this product. If requested, this information must be provided to the telephone
company.
• The REN is used to determine the quantity of devices that may be connected to the telephone line. Excessive RENs on the telephone line
may result in the devices not ringing in response to an incoming call. Typically, the sum of the RENs should not exceed five (5). To be certain
of the number of devices that may be connected to the line (as determined by the total RENs) contact the local telephone company.
• If this product causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of
service may be required. But if advance notice isn't practical, the telephone company will notify the customer as soon as possible. Also, you
will be advised of your right to file a complaint with the FCC if you believe it is necessary.
• The telephone company may make changes to its facilities, equipment, operations or procedures that could affect the operation of the
product. If this happens, the telephone company will provide advance notice so you can make the necessary modifications to maintain
uninterrupted service.
• Connection to party line service is subject to state tariffs. (Contact the state public utility commission, public service commission, or
corporate commission for information.)
• If trouble is experienced with this product, for repair or warranty information, please contact Sony Electronics Inc. If the product is causing
harm to the telephone network, the telephone company may request that you disconnect the product until the problem is resolved.
• An FCC compliant telephone cord and modular plug is provided with this equipment. This equipment is designed to be connected to the
telephone network or premises wiring using a compatible modular jack which is Part 68 compliant. See installation instructions for details.
If you have questions about this Sony product, please contact the Sony Satellite System Information Center at 1-800-838-S0NY(7669).
For questions about service, programming or billing, contact DIRECTV at 1-800-DIRECTV (347-3288).
Declaration of Conformity
Trade Name: Sony
Model No.: SAT-HD300
Responsible Party: Sony Electronics Inc.
Address: 680 Kinderkamack Road, Oradell, NJ 07649
Telephone No.: 201-930-6972
CAUTION
DO NOT ATIEMPT TO MODIFY THIS PRODUCT IN ANY WAY WITHOUT WRITTEN AUTHORIZATION FROM SONY ELECTRONICS CORPORATION.
UNAUTHORIZED MODIFICATION COULD VOID THE USER'S AUTHORITY TO OPERATE THIS PRODUCT.
THIS EQUIPMENT IS INTENDED TO RECEIVE AND DECODE SIGNALS TRANSMITIED ACCORDING TO ATSC DIGITAL TELEVISION STANDARD
A/53, DlRECTV SPECIFICATION AND IS INTENDED TO BE USED WITH AN APPROPRIATE ANTENNA, DISH AND DISPLAY DEVICE THAT YOU
MUST PROVIDE.
Dolby Digital®
Manufactured under license from Dolby Laboratories.
"Dolby" and the double-D symbol are trademarks of Dolby Laboratories.
Confidential Unpublished Works. ©1992-1 997 Dolby Laboratories, Inc. All rights reserved.
Macrovision Information
This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this
copyright protection technology must be authorized by Macrovision, and is intended for home and other limited pay-per-view uses unless
otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.
ENERGY STAR
As an ENERGY STAR® Partner,
Sony has determined that
this product or product models
meets the ENERGY STAR®
guidelines for energy
efficiency.
ENERGY STAR® is a U.S. registered mark.
2

IMPORTANT SAFETY INSTRUCTIONS
CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNER'S MANUAL
AND THOSE MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR FUTURE REFERENCE.
This set has been designed and manufactured to assure personal safety. Improper use can result in electric shock or
fire hazard. The safeguards incorporated in this unit will protect you if you observe the following procedures for
installation, use, and servicing.
This unit does not contain any parts that can be repaired by the user.
Do not defeatthe safety purpose of the
polarized or grounding-type plug. Apolarized
plug has
two blades with one wider than the
other. Agrounding type plug has
two blades
and athird grounding prong.
The wide blade or
the third prong are provided for your safety.
If
the provided plug does not fit into your outlet,
consult
an electrician for replacement ofthe
obsolete outlet.
10. Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they
exit
from the apparatus.
11. Only use attachments/accessories specified
by the manufacturer.
12. Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer. or sold
with apparatus. When acart is used, use
caution when moving the cart! apparatus
combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms
or when unused for long periods oftime.
14. Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way.
such
as power- supply cord or plug is
damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does
not operate normally, or has been dropped.
3. Heed all warnings. - All warnings on the product
and in the operating instructions should be adhered
to.
4. Follow all instructions. - All operating and use
instructions should be followed.
5. Do not use this apparatus near water. - For
example: near a bath tub, wash bowl, kitchen sink!
laundry tub! in a wet basement; or near a swimming
pool; and like.
6. Clean only with dry cloth. - Unplug this product
from the wall outlet before cleaning. Do not use
liquid cleaners.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer's instructions.
- Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from over- heating. The
openings should never be blocked by placing the
product on a bed! sofa, rug or other similar surface.
This product should not be placed in a built-in
installation such as a bookcase or rack unless proper
ventilation is provided or the manufacturer's
instructions have been adhered to.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.
1. Read these instructions. - All these safety and 9.
operating instructions should be read before the
product is operated.
2. Keep these instructions. - The safety, operating
and use instructions should be retained for future
reference.
3

IMPORTANT INFORMATION
Due to copyright restrictions, you may not be able to view some high-definition programs in
high-definition format using this product. If HD viewing is prohibited due to copyright restric-
tions, you would need to connect SO interfaces to view the program.
In certain markets, access to local channels requires a DIRECTV® Multi-Satellite Dish
Antenna. For the most current information about the availability of local channels in your area,
contact your retailer or visit DIRECTV.com. For access to all DIRECTV High Definition
programming, a triple LNB Multi-Satellite dish antenna, along with a DIRECTV® HD Receiver
and High Definition television (equipment is required.) Satellite dish antenna sold
separately.
Activation of programming may be subject to credit approval and requires valid service
address, social security number and/or major credit card. Deposit or prepayment may be
required. Programming subject to change. You must be physically located in the U.S. to
subscribe to DIRECTV service. DIRECTV services not available outside the U.S. DIRECTV pro-
gramming is sold separately and independently of DIRECTV System hardware. A valid pro-
gramming" subscription is required to operate DIRECTV System hardware. Activate your
DIRECTV programming today at 1-800,.DIRECTV (1-800-347-3288).
DIRECTV, Inc. DIRECTV, the Cyclone Design logo and Advanced Program Guide™ are trade-
marks of DIRECTV, Inc., a unit of Hughes Electronics Corp., and are used with permission.
Sony, Hi-Scan and the Sony logo are registered trademarks of Sony.
Sony Software License Agreement
AITENTION:USE OF THE SOFTWARE IS SUBJECT TO THE SONY SOFTWARE LICENSE TERMS
SET FORTH ON PAGE 121. USING THE SOFTWARE OR THE PRODUCT IN WHICH IT IS INCOR-
PORATED INDICATES USER'S ACCEPTANCE OF THESE LICENSE TERMS. IF THE USER DOES
NOT ACCEPT THESE LICENSE TERMS,THE USER SHOULD IMMEDIATELY RETURN THE ENTIRE
PRODUCT IN ITS ORIGINAL PACKAGING IN ORDER TO RECEIVE A FULL REFUND OF THE PUR-
CHASE PRICE.
4

TABLE OF CONTENTS
Safety Warning 1-2
Important Safety Instructions 3
Important Information .4
Table of Contents 5-6
1. Introduction 1-1. A New World of Digital Entertainment 7
1-2. Main Features 8
2. Important Overview 2-1. Sending Signals .. , 9
2-2. TV Signal Formats 10
2~3. Display Formats 11
2-4. Normal and Wide Format Signals 12-13
2-5. Audio Signals 14-15
2-6. On-Screen Display 16-17
3. Setup and Connections 3-1. Unpacking 18-19
3-2. Back Panel of the DIRECTV® HD Receiver 20-21
3-3. General Recommendations 22
3-4. Connecting to Antennas 23-26
3-5. TV Connection 27-30
3-6. VCR Connection 31-32
3-7. Audio Connection 33-34
3-8. Remote Control RF Antenna Connection .35
4. Front Panel and 4-1. Using the Front Panel of the DIRECTV® HD Receiver 36
4-2. Using the Remote Control 37-39
4-3. Programming the Remote Control .40
4-4. Remote Control Codes for Other Components .41-42
5. Initial Setup 43
5
6. Basic Operation
6-1. Viewing the Channel Banner 44-45
6-2. Accessing Favorite Channels .46
6-3. Freeze Screen .47
6-4. Subscription to DIRECTV® programming and
ANT/CABLE-Only operation .48

7. Advanced Program Guide™ 7-1. About the Advanced Program Guide™ .49
7-2. Layout of the Advanced Program Guide™ Screen ., .. 50-51
7-3. Moving through the Advanced Program Guide™ 52-53
7-4. Selecting a Program 54
7-5. Getting More Program Information 55-56
7-6. Setting a Timer/Record Event for Future Viewing 57
7-7. Purchasing DIRECTV® Pay Per View Programs 58
7 -8. Searching for Programs by Category 59-60
7-9. Searching for Programs by Keyword 61
8. Customization 8-1. Accessing the On-screen Menu 62
8-2. The Structure of the On-Screen Menu 63
8-3. Managing Program Purchases 64
8-4. Checking the Messages 65
8-5. Setting a Timer/Record Event 66
8-6. Modifying a Timer/Record Event 67
8-7. Initializing the System 68-75
8-8. Managing Channels .76-79
8-9. Setting the Clock 80-81
8-10. Setting Default Signal Out 82
8-11. Hook-up Help 83
8-12. Setting the Audio 84-88
8-13. Choosing the Aspect Ratio 89-91
8-14. Setting Digital Caption 92
8-15. Setting Digital Caption Style 93
8-16. Setting Closed Caption 94
8-17. Advanced 95
8-18. Running Auto Demo 96
8-19. Setting Locks 97-102
8-20. Getting the System Information 103-106
B-21. Testing the System 107-109
8-22. Replace Card 110
8-23. VCR Control Setup 111
8-24. Remote Control Setup 112
9. Help 113-114
Product Specifications 115
Troubleshooting 116-119
Limited Warranty 120
Software License Agreement 121
Index , .. '" 122 6

1. INTRODUCTION
1-1. ANew World of Digital Entertainment
Welcome to the SAT-HD300 DIRECTV® HD Receiver, an advanced digital satellite receiver that show-
cases a new generation of digital entertainment.
The DIRECTV HD Receiver delivers a variety of programs from DIRECTV and has a built-in HD Receiver
that serves as a digital receiver that makes it possible to view digital programs even on your analog TV.
However an analog TV will not display the HD quality.
The Advanced Program Guide™ delivered via satellite service also enables you to access and view
program listings for over-the-air broadcasts and cable as well as DIRECTV® programming.
7

1-2. Main Features
Ultimate Entertainment
•A Wide Variety of Programs
Hundreds of channels are available by subscription from DIRECTV.
• DIRECTV Advanced Program Guide™
Instant access to up to seven days of program listings.
Ability to jump a day or 6 hours at a time.
Ability to search and tune by program title, keyword and category.
Technical Flexibility
• Seamless Tuning
Tune seamlessly to over-the-air, cable and satellite.
•Multiple Output Jacks
Multiple output jacks are provided on the back panel of the DIRECTV® HD Receiver ensuring
maximum connectively to a variety of display devices.
• Screen Format Adaptability
Various screen formats are available including 10BOi, 720p, 4BOp, 480i, variable 1, variable 2,
variable 3, auto DVI, and true native modes.
• ANT/CABLE Only Mode
Viewing analog/digital broadcasting with an over-the-air antenna and cable service.
• Simultaneous 480i Display Output
Supporting simultaneous480i Display Output for VCR-recording or viewing on an analog TV.
Superior Performance
• Crisp Picture
High-definition or resolution with a 16:9 aspect ratio when connected to a high-definition moni-
tor.
• Superior Sound
Sensational sound with Dolby Digital® 5.1 channels when connected to a Dolby Digital® compati-
ble audio receiver system.
• DVI-HDTV Output
For an all-digital connection to DVI-HDTV monitors.
• RF Remote Control
Remote control access from outside a cabinet or even from another room within your home.
Convenient Use
• Help
Easy-to-use on-screen menus with instant spot help and brief on-screen user's guide.
• Hook-up Help
The on-screen menus show connection schemes on the DIRECTV HD Receiver.
• Setup Wizard
Easy-to-use Wizard based System Setup
• Easy Recording to VCR
Up to seven days of program guide information from which shows can be quickly selected for
automatic VCR recording.
8

2. IMPORTANT OVERVIEW .
2-1. Sending Signals
SateJlite
L.::::::::==l Analog Cable service
Digital Analog
signal signal
Digital broadcasting is a new way of sending programs over the airwaves with superior qual-
ity video and audio. The DIRECTV® HD Receiver enables you to take full advantage of digital
broadcasting. To fully enjoy it, it is helpful understand the ways the program signals are sent.
There are two types of TV signal formats; analog (often called NTSC format; National Television
System Committee) and digital (ATSC format; Advanced Television System Committee). Digital
formats are classified into three categories: High-Definition (HD), Enhanced Definition (ED), and
Standard Definition (SO) according to the resolution or digital picture quality.
There are also three ways that program signals can be received; over-the-air (NTSC, ATSC),
cable and satellite.
9

2-2. TV Signal Formats
Standard Comparison Table
Signal Format Analog
Digital
SO
HO
Active Lines 480i
480p 720p or 1080i
Sound
Stereo (2 ch)
Dolby Digital® (5.1 ch)
Dolby Digital (5.1 ch)
MPEG Audio (2 ch)
Aspect Rati 0 4:3
4:3 or 16 :9 16: 9
640 x 480 1280 x 720
Resolution 720 x 480
704 x 480
1920 x 1080
The digital TV standards allow several different formats. Broadcasters can choose between
th ree fo rm ats:
• 480p - The picture is 704 x 480 pixels, sent at 60 complete frames per second (480i is
also possible).
• 720p - The picture is 1280 x 720 pixels, sent at 60 complete frames per second.
• 1080i - The picture is 1920 x 1080 pixels, sent at 60 interlaced frames per second (30
complete frames per second).
(The "p" and "i" designations stand for "progressive" and "interlaced." In a progressive for-
mat, the full picture updates every sixtieth of a second. In an interlaced format, half of the pic-
ture updates every sixtieth of a second.)
The 480p and 480i formats are called the SO formats, and 480i is roughly equivalent to a nor-
mal analog TV picture. The 720p and 1 08Di formats are called the HO formats.
Some analog televisions can display a picture 720 pixels wide by 480 pixels high, that's a total
of 345,600 pixels. HO digital signals can have a maximum resolution of 1920 x 1080, that's
2,073,600 pixels, or six times more pixels than the older resolution. Pictures will be crisper and
cleaner, with more detail in every close-up and every panorama.
10

2. IMPORTANT OVERVIEW
2-3. Display Formats
The DIRECTV® HD Receiver provides several display formats. The FORMAT button in the front
panel changes the display format in the cycle of 1 D8Di, 720p, 48Dp, 48Di, native,
variable 1, variable 2, variable 3 and Auto DVI** modes. In 1080i, 720p, 480p and 480i
modes, all input signal formats are converted to the chosen display format. In native, vari-
able 1, variable 2 and variable 3 modes, output display format is automatically adapted
depending on input signal format. In Auto DVI mode, the output display format is automati-
cally adapted based on the preferred resolution format of the DVI-HDTV monitor. The format
may be converted from the original broadcast format.
Display Format modes
Input Signal format
Output Signal format
1080i
all formats
1080i
720p all formats
720p
480p
all formats
480p
480i
all formats 480i
native
1080i 1080i
720p
720p
480p 480p
480i
480i(Component, DVI), 480p(RGB)
variable 1
1080i 1080i
7200 720p
4800/480i
480p
variable 2 1080i/720p
1080i
480p/480i
480p
variable 3
10BOi/7200
720p
1080i
480p
AUTO DVI** all formats
changes according to monitor type
OUTPUT CONNECTION
AVAILABLE FORMATS
YPbPr*
~
1080i/720p/480p/480i/native/Variable 1/variable 2/variable 3
0
0~ a
RGB*
~
1080i/720p/480p/native/variable 1/variable 2/variable 3
DVI-HDTV*
i~i
1080i/720p/480p/480i/native/variable 1/Variable 2/
variable 3/ Auto DVI**
Video 1/2
til
All formats converted to 480i
S Video
;
All formats converted to 480i
RF Out to TV
2,
All formats converted to 480i
11
* Only one of the YPbPr, RGB or DVI-HDTV jacks is available at anyone time, depending on
the TYPE switch setting and DVI-HDTV connection status.
** Format available when using the DVI-HDTV output to connect to a DVI-HDTV monitor.

2-4. Normal and Wide Format Signals
When you view a high-definition picture with 480i or 480p format setting, the WIDE MODE but-
ton on the remote control changes the wide mode in the cycle of Letterbox, Cropped, to
Squeezed.
When you view a standard definition picture with 720p or 1080i format setting, the WIDE
MODE button on the remote control changes the wide mode in the cycle of Normal, Wide,
Panorama, Zoom, to Cine-Zoom. (Refer to section 8-13, 'Choosing the Aspect Ratio')
WHEN YOU SET THE FORMAT TO SDTV (480i/480p)
Program Format
Standard Definition Output Format
t Standard Definition
antenna
High-Definition
No Adjustment Options
Letter box
Choose when you want to view a
wide format (16:9) picture on a nor-
mal screen (4:3) without squeezing.
----.---,I---~ Cropped
Choose when you want to view a
picture filling the entire screen
while keeping the wide format.
Left and right portions of the pic-
ture will not be shown.
Squeezed
Choose when you want to view a full
picture filling the entire screen with
. no black bars. The picture in a 16:9
format will be horizontally adjusted or
squeezed to fit the 4:3 ratio monitor.
This setting can also be useful when
used with 16:9 aspect ratio monitors
or with 4:3 aspect ratio monitors with
a "16:9 enhancement" feature.
12

2. IMPORTANT OVERVIEW
2-4. Normal and Wide Format Signals
WHEN YOU SET THE FORMAT TO HOTV (1080inZOp)
Program Format
High-Definition Output Format
*Three temporary adjustment options available
High-Definition
Normal
Choose when you want to view a picture
with an original 4:3 aspect ratio on your
16:9 TV. Black or gray bars will show at the
left and right sides.
Wide
Choose when you want to evenly stretch the
width of a normal picture to fill the entire
screen.
Zoom
Choose when you want to fill the entire
screen with the picture. The image will be
altered both horizontally (stretched) and
vertically (cropped). The top and bottom
portions of the picture will not be shown.
Zoom1 shows you the picture with a trade-
off between distortion and screen coverage.
Adjustment
Required
------+-~ Panorama
Choose when you want to evenly stretch the
edges of a normal picture to fill a wide
screen.
Standard Definition
antenna
13
CINE-Zoom
Choose when you want to adjust zooming.
*Note.
The HDTV formats should always be broadcast in the 16:9 aspect ratio.
However, you may choose one of three temporary options to select for your
preference. The three options are Standard, Expand and Shrink.

2-5. Audio Signals
Digital Audio Signals
I
""" I.
~:~?.~;
!
Dolby Digital Sound with 5.1 Channels
The DIRECTV® HD Receiver will be the focal center of your home entertainment system comprising a
variety of components, such as TV, DVD, VCR, etc. and external audio systems. Since digital programs
being broadcast contain digital-quality audio, you can create a home theater by sending audio signals
from the DIRECTV HD Receiver to your audio system externally. HD digital signals use the Dolby
Digital® audio encoding system - the same digital sound used in many movie theaters, on DVDs, and
in many home theater systems.
When you tune to a channel, the DIRECTV HD Receiver can send signals either to a Dolby Oigital®
decoder/receiver or to a peM (normal digital) decoder. (* Refer to Section 3-7 Connection for Audio
for making the required external connections to your system.)
Dolby Digital® audio! formally known as Audio Coding 3rd Generation is a
coding technique that can provide up to five independent, full frequency
response audio channels (three in left, center, and right, two in rear left
and right,) and one low frequency effect for a sound you can feel.
14

2. IMPORTANT OVERVIEW
2-5. Audio Signals
Analog Audio Signals
Analog stereo amplifier
AUDIO IN
~
Audio cables
O
~o
'\.:.:.:.:.I'
O\ltt111o ~
~~J ~
(1080il720p/480p) (1080il720p/480p/48(
The analog audio outputs may be used to drive an external Hi-Fi audio system instead of the
TV speakers. These stereo outputs are activated by setting the Analog Mode in the Audio
menu to Stereo.
If you set the Analog Mode to SAP (Second Audio Program), you can hear the program's dia-
log in another language such as French or Spanish, if provided on the analog broadcast.
15

Main M.enu
You can adjust the setup through a user-friendly on-screen menu using the remote control.
While viewing a program, the on-screen menu will appear on your TV screen if you press the
MIffiNUbutton on your remote control. The on-screen menu is operated using a simple,
straight-forward 'Highlight and Select' process. You just highlight a menu item by using
"j,,,~~non your remote control, and select it by pressing"-+- ". Theon-screen menu also
offers visual cues for easy guidance.
A(hY(UlI~ed Program GlJide™
The DIREGTVAdvanced Program Guide is an on-screen listing of current andfuture programs
that are available from DIRECTV. The DIHECTV® HD Receiver offers you a comprehensiVe pro"
gram list that contains information aboutprogramswith hundreds of channels, including anac
log Antenna and digital (ATSC). If you do not subscribe toOIRECTV® programming, you will
be to Advanced Program Guide.
16

2-6. On-Screen Display
Help
First. certain features and terminologies used in the on-screen menus require your basic
understanding to fully utilize their capabilities. The DIRECTV® HD Receiver provides a power-
ful feature called "Help" that describes highlighted menu item to help you understand the fea-
tures. Press and hold the "HELP" button to display the "Help". Once you release the button,
the Help menu disappears from the screen.
Second, if you press the "HElP" button while you are viewing a program with no menus on -
screen, the OIRECTV HD Receiver provides a comprehensive on-screen user's guide. It
describes how to use your receiver.
This is, in fact an on-line version of this Operating Guide.
17

3-1. Unpacking
Make sure you have received all these items listed below with the DIRECTV® HD Receiver.
HDTV
Remote Control
FAVORITE
~
FREEZE EXIT PREVCH
SI~E
o HELP CC 0
CODE SET 00 MODE
o
Cables
{;)
SVIDEOJack
Y PB PR
ComponenlJacks
Batteries
(( AA ({q
(( AA ({q
Access Card
ACCESS
CARD
Remote Control
RF Antenna
18

3. SETUP AND CONNECTIONS
3-1. Unpacking
DIRECTV® HD Receiver
The DIRECTV HD Receiver is capable of receiving signals from the satellite dish, cable, and/or over-the-air
antenna and sending the decoder signals to your TV.
Remote Control
In addition to the DIRECTV HD Receiver, the remote control can be programmed to control many other
devices.
Batteries
To install the batteries, slide open the battery compartment and insert the two AA batteries provided.
Component Out Jacks and Cables
Component Cables are used to connect the DIRECTV HD Receiver to an industry standard Y /Pb/Pr compat-
ible Monitor.
DVI-HDTV port and Cable
DVI cable is used to connect the DIRECTV HD Receiver to a DVI-HDTV compatible HD monitor.
S-Video Jack and Cable
An S-Video jack is provided on the DIRECTV HD Receiver and is used together with audio cables.
Remember to connect the left and right audio cables. An S-Video jack carries only the picture signals, not
the sound.
AudioNideo Jacks and Cables
The Audio/Video jacks provide good picture and sound quality. They are used for making most Audio/Video
connections between components. The Audio/Video jacks may be color coded (yellow for video, red for
right audio, and white for left audio). If your component has only one input for audio (mono), connect it to
the left (white L/mono) audio jack on the DIRECTV HD Receiver.
RF (Radio Frequency) Jacks and Coaxial Cables (F-type)
RF jacks are necessary for reception of over-the-air broadcasts, cable, and DIRECTV signals. These jacks
are also required for antenna or cable connections. The RF and coaxial jacks on the DIRECTV HD Receiver
are labeled Antenna, Cable, Satellite and OUT TO TV. An RG-6 type coaxial cable is required for satellite
signal distribution.
Telephone Jack and Cord
A telephone line cord is required to connect the DIRECTV HD Receiver to a phone line. If you choose to sub-
scribe to DIRECTV® programming, this phone line is required to be connected.
Access Card
The Access Card is the means by which DIRECTV controls the distribution of its service. The card must be
inserted into the access card slot (on the front of the DIRECTV HD Receiver) at all times to ensure recep-
tion of satellite signals.
Remote Control RF Antenna
The Remote Control RF Antenna can be used with the supplied remote control.
VCR Controller
19 The VCR Controller allows the Record function to automatically operate your VCR.