Sony STR-DA3200ES - Es Receiver User manual

SERVICE MANUAL
AUDIO POWER
SPECIFICATIONS (US, Canadian models)
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION:
With 8 ohm loads, both channels driven, from
20 – 20,000 Hz; rated 120 watts per channel
minimum RMS power, with no more than
0.09% total harmonic distortion from 250
milliwatts to rated output.
Amplifier section (US, Canadian models)
POWER OUTPUT
Rated Power Output at Stereo Mode
1) 2)
(8 ohms 20 Hz – 20 kHz,
THD 0.09%):
120 W + 120 W
Reference Power Output at Stereo Mode
2)
(4 ohms 20 Hz – 20 kHz,
THD 0.15%):
120 W + 120 W
Reference Power Output
(8 ohms 1 kHz, THD 0.7%)
FRONT
2)
:
130 W + 130 W
CENTER
2)
:
130 W
SURROUND
2)
:
130 W + 130 W
SURROUND BACK
2)
:
130 W + 130 W
Reference Power Output
(4 ohms 1 kHz, THD 0.7%)
FRONT
2)
:
130 W + 130 W
CENTER
2)
:
130 W
SURROUND
2)
:
130 W + 130 W
SURROUND BACK
2)
:
130 W + 130 W
1)
Depending on the sound field settings and the
source, there may be no sound output.
2)
Measured under the following conditions:
Power requirements: 120 V AC, 60 Hz
Reference Power Output
(8 ohms 20 Hz – 20 kHz,
THD 0.09%)
FRONT
2)
:
120 W + 120 W
CENTER
2)
:
120 W
SURROUND
2)
:
120 W + 120 W
SURROUND BACK
2)
:
120 W + 120 W
Reference Power Output
(4 ohms 20 Hz – 20 kHz,
THD 0.15%)
FRONT
2)
:
120 W + 120 W
CENTER
2)
:
120 W
SURROUND
2)
:
120 W + 120 W
SURROUND BACK
2)
:
120 W + 120 W
Reference Power Output at Stereo Mode
(8 ohms 1 kHz, THD
10%):
150 W + 150 W
Reference Power Output at Stereo Mode
(4 ohms 1 kHz, THD
10%):
150 W + 150 W
Frequency response
PHONO RIAA equalization curve
±0.5 dB
MULTI CHANNEL
INPUT, SA-CD/CD,
TAPE/CD-R,
MD/DAT, DVD,
VIDEO 1/2/3
10 Hz – 100 kHz
±3 dB
Reference Power Output
(8 ohms 1 kHz, THD 10%)
FRONT
2)
:
150 W + 150 W
CENTER
2)
:
150 W
SURROUND
2)
:
150 W + 150 W
SURROUND BACK
2)
:
150 W + 150 W
Reference Power Output
(4 ohms 1 kHz, THD 10%)
1)
Depending on the sound field settings and the
source, there may be no sound output.
2)
Measured under the following conditions:
Power requirements: 230 V AC, 50/60 Hz
(in countries/area in Europe
other than the UK)
240 V AC, 50/60 Hz
(in the UK and general area)
Amplifier section (AEP, UK,Taiwan models)
POWER OUTPUT
Rated Power Output at Stereo Mode
1) 2)
(8 ohms 1 kHz, THD
0.7%):
125 W + 125 W
Inputs (Analog)
Inputs (Digital)
PHONO Sensitivity: 2.5 mV
Impedance: 50 kohms
S/N: 86 dB (A, 20 kHz
LPF)
MULTI CHANNEL
INPUT, SA-CD/CD,
TAPE/CD-R, MD/DAT,
DVD, TV/SAT,
VIDEO1/2/3
Sensitivity: 150 mV
Impedance: 50 kohms
S/N: 96 dB (A, 20 kHz
LPF)
DVD, TAPE/CD-R, SA-
CD/CD (Coaxial) Impedance: 75 ohms S/N: 96 dB (A, 20 kHz
LPF)
VIDEO 1/2/3, TV/SAT,
MD/DAT (Optical) S/N: 96 dB (A, 20 kHz LPF)
Reference Power Output at Stereo Mode
2)
(4 ohms 1 kHz, THD
0.7%):
125 W + 125 W SURROUND
2)
:
150 W + 150 W
SURROUND BACK
2)
:
150 W + 150 W
CENTER
2)
:
150 W
FRONT
2)
:
150 W + 150 W
MULTI CHANNEL AV RECEIVER
SPECIFICATIONS
STR-DA3200ES/DG1000
Ver. 1.0 2006.09
– Continued on next page –
9-887-378-01
2006I05-1
© 2006.09
Sony Corporation
Home Audio Division
Published by Sony Techno Create Corporation
US Model
STR-DA3200ES/DG1000
Canadian Model
AEP Model
UK Model
Taiwan Model
STR-DA3200ES
This receiver incorporates Dolby* Digital and Pro Logic Surround and the DTS** Digital Surround System.
*Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, “Surround EX”, and the double-D symbol are trademarks of Dolby Laboratories.
** Manufactured under license from Digital Theater Systems, Inc. U.S. Pat.
No’s. 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535 and other U.S.
and world-wide patents issued and pending.
“DTS”, “DTS-ES”, “Neo:6”, and “DTS 96/24” are trademarks of Digital Theater Systems, Inc.
Copyright 1996, 2003 Digital Theater Systems, Inc. All Rights Reserved.
Photo: STR-DA3200ES

2
STR-DA3200ES/DG1000
Notes on chip component replacement
•Never reuse a disconnected chip component.
•Notice that the minus side of a tantalum capacitor may be
damaged by heat.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
Outputs
EQUALIZER
FM tuner section
Tuning range 87.5 - 108.0 MHz
Antenna (aerial) FM wire antenna (aerial)
Antenna (aerial) terminals
75 ohms, unbalanced
Sensitivity
Mono: 18.3 dBf, 2.2 µV/75 ohms
Stereo: 38.3 dBf, 22.5 µV/75 ohms
Usable sensitivity 11.2 dBf, 1 µV/75 ohms
S/N
Mono: 76 dB
Stereo: 70 dB
Harmonic distortion at 1 kHz
Mono: 0.3%
Stereo: 0.5%
Separation 45 dB at 1 kHz
Frequency response 30 Hz – 15 kHz, +0.5/–2
dB
Selectivity 60 dB at 400 kHz
AM tuner section (US, Canadian models)
Tuning range 530 – 1,710 kHz
3)
(With 10-kHz tuning scale)
531 – 1,710 kHz
3)
(With 9-kHz tuning scale)
Antenna (aerial) Loop antenna (aerial)
3)
You can change the AM tuning scale to either 9
kHz or 10 kHz. After tuning in any AM station,
turn off the receiver. While holding down
TUNING MODE, press POWER on the receiver.
All preset stations will be erased when you change
the tuning scale. To reset the scale to 10 kHz (or 9
kHz), repeat the procedure.
TAPE/CD-R, MD/DAT,
VIDEO1/2 (AUDIO OUT) Voltage:150 mV Impedance: 1 kohms
FRONT L/R, CENTER,
SURROUND L/R,
SURROUND BACK L/R,
SUB WOOFER
Voltage: 2 V
Impedance: 1 kohms
Gain levels ±10 dB, 1 dB step
AM tuner section (AEP, UK,Taiwan models)
Tuning range 531 – 1,602 kHz
Antenna (aerial) Loop antenna (aerial)
Usable sensitivity 50 dB µ/m (at 999 kHz)
S/N54 dB (at 50 mV/m)
Harmonic distortion 0.5% (50 mV/m, 400 Hz)
Selectivity 35 dB
General (AEP, UK,Taiwan models)
Power requirements 230 V AC, 50/60 Hz
(in countries/area in
Europe other than the UK)
240 V AC, 50/60 Hz
(in the UK and general
area)
Power consumption 480 W
Power consumption (during standby mode)
1 W
AC outlets
Dimensions
1 switched, 100 W/0.4 A
MA
X
(Models for countries/
areas in Europe other than
the UK.)
430 ×175 ×430 mm
(width/height/depth)
including projecting parts
and controls
Mass (Approx.) 15.5 kg
Video section
Inputs/Outputs
Video: 1 Vp-p, 75 ohms
Svideo: Y:1Vp-p, 75 ohms
C: 0.286 Vp-p, 75 ohms
COMPONENT VIDEO:
Y: 1 Vp-p, 75 ohms
P
B
/C
B
: 0.7 Vp-p, 75 ohms
P
R
/C
R
: 0.7 Vp-p, 75 ohms
80 MHz HD Pass Through
(When “PROGRESSIVE
OUT” is set to “OFF”.)
General (US, Canadian models)
Power requirements 120 V AC, 60 Hz
Power consumption 480 W/580 VA (U/CA)
Power consumption (during standby mode)
1 W
AC outlets 2 switched, 100 W/0.8 A
MA
X
Supplied accessories
Operating Instructions
Quick Setup Guide (1)
Optimizer microphone ECM-AC2 (1)
FM wire antenna (aerial) (1)
AM loop antenna (aerial) (1)
AC power cord (mains lead) (1)
Remote commander RM-AAL003 (1) (US, Canadian models)
Remote commander RM-AAL004 (1) (AEP, UK, Taiwan models)
Remote commander RM-AAU008 (1) (DA3200ES)
R6 (size-AA) batteries (4) (DA3200ES)
R6 (size-AA) batteries (2) (DG1000)
Design and specifications are subject to
change without notice.
Dimensisons 430 ×175 ×430 mm
(17 ×7 ×17 in) (width/
height/depth)
including projecting parts
and controls
Mass (Approx.) 15.5 kg (34 lb 3 oz)
Usable sensitivity 50 dB µ/m (at 1,000 kHz or
999 kHz)
S/N54 dB (at 50 mV/m)
Harmonic distortion 0.5% (50 mV/m, 400 Hz)
Selectivity at 9 kHz : 35 dB
at 10 kHz : 40 dB
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0SUR
LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES
PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE
FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS
QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT
DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS
PUBLIÉS PAR SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs,screws,
and all other exposed metal parts forAC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’instructions to use these
instruments.
2. A battery-operatedAC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operatedACvoltmeter. The “limit” indication
is 0.75V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2VAC range are suitable. (See
Fig. A)
Fig. A. Using an AC voltmeter to check AC leakage.
1.5 k Ω 0.15 µ FAC
voltmete
r
(0.75 V)
To Exposed Metal
Parts on Set
Earth Ground

3
STR-DA3200ES/DG1000
TABLE OF CONTENTS
1. SERVICING NOTES .............................................. 4
2. GENERAL .................................................................. 10
3. DISASSEMBLY
3-1. Disassembly Flow .......................................................... 18
3-2. Case ................................................................................ 19
3-3. Front Panel Assy ............................................................. 19
3-4. S-VIDEO/CIS Board ...................................................... 20
3-5. Tuner............................................................................... 20
3-6. E-VOLUME Board ........................................................ 21
3-7. VIDEO Board................................................................. 21
3-8. SP TERMINAL Board ................................................... 22
3-9. ANALOG Board ............................................................ 22
3-10. Power Transformer (T01) ............................................... 23
3-11. MAIN Board................................................................... 23
4. TEST MODE............................................................. 24
5. ELECTRICAL ADJUSTMENTS ........................ 27
6. DIAGRAMS
6-1. Block Diagram – CONTROL Section – ......................... 30
6-2. Block Diagram – DSP Section – .................................... 31
6-3. Block Diagram – HDMI RECEIVER Section – ............ 32
6-4. Block Diagram – HDMI TRANSCEIVER Section – .... 33
6-5. Block Diagram – ANALOGAUDIO Section – ............. 34
6-6. Block Diagram
– ELECTRICAL VOLUME Section –........................... 35
6-7. Block Diagram – POWER AMP Section – .................... 36
6-8. Block Diagram – VIDEO Section – ............................... 37
6-9. Block Diagram – DISPLAY Section – ........................... 38
6-10. Block Diagram – POWER SUPPLY Section – .............. 39
6-11. Schematic Diagram – DIGITAL Board (1/5) – .............. 41
6-12. Schematic Diagram – DIGITAL Board (2/5) – .............. 42
6-13. Schematic Diagram – DIGITAL Board (3/5) – .............. 43
6-14. Schematic Diagram – DIGITAL Board (4/5) – .............. 44
6-15. Schematic Diagram – DIGITAL Board (5/5) – .............. 45
6-16. Schematic Diagram
– DIGITAL Board (Component Side) – ......................... 46
6-17. Schematic Diagram
– DIGITAL Board (Conductor Side) –........................... 47
6-18. Printed Wiring Board – DSP Board – ............................ 48
6-19. Schematic Diagram – DSP Board – ............................... 49
6-20. Printed Wiring Board
– HDMI Board (Component Side) – .............................. 50
6-21. Printed Wiring Board
– HDMI Board (Conductor Side) – ................................ 51
6-22. Schematic Diagram – HDMI Board (1/6) – ................... 52
6-23. Schematic Diagram – HDMI Board (2/6) – ................... 53
6-24. Schematic Diagram – HDMI Board (3/6) – ................... 54
6-25. Schematic Diagram – HDMI Board (4/6) – ................... 55
6-26. Schematic Diagram – HDMI Board (5/6) – ................... 56
6-27. Schematic Diagram – HDMI Board (6/6) – ................... 57
6-28. Printed Wiring Board
– XM Board (DA3200ES: US, Canadian models/
DG1000) – ...................................................................... 58
6-29. Schematic Diagram – XM Board (DA3200ES: US,
Canadian models/DG1000) – ......................................... 59
6-30. Printed Wiring Board – CIS Board (DA3200ES) –........ 60
6-31. Schematic Diagram – CIS Board (DA3200ES) – .......... 61
6-32. Printed Wiring Board – ANALOG Board – ................... 62
6-33. Schematic Diagram –ANALOG Board – ...................... 63
6-34. Printed Wiring Board – MAIN Board – ......................... 65
6-35. Schematic Diagram – MAIN Board (1/2) – ................... 66
6-36. Schematic Diagram – MAIN Board (2/2) – ................... 67
6-37. Printed Wiring Board – E-VOLUME Board – ............... 68
6-38. Schematic Diagram – E-VOLUME Board – .................. 69
6-39. Printed Wiring Board – A CLASS AMP Board – .......... 70
6-40. Schematic Diagram – A CLASS AMP Board – ............. 71
6-41. Printed Wiring Board – POWER AMP Board – ............ 72
6-42. Schematic Diagram – POWER AMP Board – ............... 73
6-43. Printed Wiring Board – BIAS Board –........................... 74
6-44. Schematic Diagram – BIAS Board – ............................. 75
6-45. Printed Wiring Board –VIDEO Board –........................ 76
6-46. Schematic Diagram – VIDEO Board (1/3) –.................. 77
6-47. Schematic Diagram – VIDEO Board (2/3) –.................. 78
6-48. Schematic Diagram – VIDEO Board (3/3) –.................. 79
6-49. Printed Wiring Board – S-VIDEO Board –.................... 80
6-50. Schematic Diagram – S-VIDEO Board –....................... 81
6-51. Printed Wiring Board –VIDEO 3 Board –..................... 82
6-52. Schematic Diagram – VIDEO 3 Board – ....................... 83
6-53. Printed Wiring Board – DISPLAY Board – ................... 84
6-54. Schematic Diagram – DISPLAY Board – ...................... 85
6-55. Printed Wiring Boards – KEY Section –........................ 86
6-56. Schematic Diagram – KEY Section – ............................ 87
6-57. Printed Wiring Boards – SPEAKER Section – .............. 88
6-58. Printed Wiring Boards – DC Section – .......................... 89
6-59. Printed Wiring Board –AC Board –............................... 90
6-60. Schematic Diagram – POWER SUPPLY Section – ....... 91
7. EXPLODED VIEWS
7-1. Case Section ................................................................... 124
7-2. DISPLAY Board Block .................................................. 125
7-3. Front Panel Block ........................................................... 126
7-4. VIDEO Board Block ...................................................... 127
7-5. ANALOG Board Block .................................................. 128
7-6. MAIN Board Block ........................................................ 129
7-7. Heat Sink Block.............................................................. 130
8. ELECTRICAL PARTS LIST............................... 131

4
STR-DA3200ES/DG1000
COLOR VARIATION
Model Destination COLOR
BLACK SILVER
US, Canadian z
STR-DA3200ES AEP, UK zz
Taiwan z
STR-DG1000 US z
SECTION 1
SERVICING NOTES
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
•Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
•Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
•Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
•MODEL IDENTIFICATION
Model PART No.
DA3200ES: US and Canadian models 2-668-097-2[]
DA3200ES: AEP model 2-668-097-3[]
DA3200ES: UK model 2-668-097-4[]
DA3200ES: Taiwan model 2-668-097-6[]
DG1000 2-696-797-0[]
PART No.
– Back Panel –
NOTE OF REPLACING THE IC3505 AND IC3508 ON
THE HDMI BOARD
When IC3505 and IC3508 on the HDMI board are damaged,
exchange the new HDMI board for the HDMI board which IC
damaged. When throwing away the HDMI board, be sure to throw
away after destroying IC3505 and IC3508 physically with the
hammer etc.
UPDATE OF SOFTWARE OF THE SYSTEM CONTROLLER (IC2054)
Perform operation of the following when the update of software of the system controller (IC2054) is necessary.
Connect:
Procedure:
1. Turn off the main power and setting the jig referring to Fig. 1 (Note: Do this setting before connecting jig with the set).
2. Remove the KNOB (VOL) ASSY and connect CN717 (M-VOL board) and PC by using the jig.
3. Turn on the main power and perform the operation according to the application.
4. After “Please Reset” is displayed, reset switch on the jig is pushed and update is completed.
5. Turn off the main power and remove the jig.
6. Turn on the main power.
JIG
(Part No. : J-2501-300-A)
for PC CN717
M-VOL board
SW2 SW1
(RESET)
SW1: up, SW2: down
Fig.1 Setting for jig

5
STR-DA3200ES/DG1000
DIGITAL/HDMI BOARDS SERVICE POSITION
Note: Follow the disassembly procedure in the numerical order given.
Note: In checking the DIGITAL board, remove the HDMI board.
8DIGITAL board
7HDMI board
2eight screws
(BVTP3 × 8)
3three screws
(B3 × 6)
4two screws
(BVTP3 × 8)
6screw
(BVTP3 × 8)
1screw
(BVTP3 × 8)
5Raise and remove upwards after pulling to the front.
HDMI board
DIGITAL board
insulated shee
t
insulated sheet

6
STR-DA3200ES/DG1000
AMP BLOCK SERVICE POSITON
In checking the AMP block, prepare jig (extension cable J-2501-290-A: 500 mm 9 core/J-2501-291-A: 500 mm 12 core).
DISPLAY BOARD SERVICE POSITON
A CLASS AMP board
Connect jig (extension cable
J-2501-291-A) to the E-VOLUME board
(CNS1201) and A CLASS AMP board
(CNS1501).
E-VOLUME board
Connect jig (extension cable J-2501-290-A)
to the E-VOLUME board (CNS1202) and A CLASS AMP board (CNS1502).
DISPLAY board
POWER SW board
front panel block

7
STR-DA3200ES/DG1000
VIDEO BOARD SERVICE POSITON
In checking the VIDEO board, prepare jig (extension cable J-2501-231-A: 300 mm 15 core).
ANALOG BOARD SERVICE POSITON
In checking the ANALOG board, remove the VIDEO board and S-VIDEO board.
Connect jig (extension cable J-2501-231-A)
to the VIDEO board (CN6802) and S-VIDEO board (CNS6903).
VIDEO board
S-VIDEO board
insulated shee
t
ANALOG board
insulated sheet

8
STR-DA3200ES/DG1000
MAIN/E-VOLUME BOARDS SERVICE POSITON
In checking the MAIN/E-VOLUME board, prepare jig (extension cable J-2501-290-A: 500 mm 9 core/J-2501-291-A: 500 mm 12 core).
Note: Be sure to ground the MAIN board with a clip when checking it.
– MAIN board –
– E-VOLUME board –
In checking the board, make two
capacitors discharge for electric
shock prevention. (R: 800 Ω/2W)
clip
chassis
Extension cable (Part No. : J-2501-291-A)
to the E-VOLUME board (CNS1201) and
A CLASS AMP board (CNS1501).
MAIN board
C1402
C1402
C1401
C1401
CAUTION
A CLASS AMP board
Extension cable (Part No. : J-2501-290-A)
to the E-VOLUME board (CNS1202) and
A CLASS AMP board (CNS1502).
E-VOLUME board
insulated sheet
JWH1210, JWH1208
(Even if it attaches a clip in JWH1208
and attaches it in JWH1210, it is satisfactory.)
MAIN board
E-VOLUME board
insulated sheet
clip
Extension cable (Part No. : J-2501-291-A)
to the E-VOLUME board (CNS1201) and
A CLASS AMP board (CNS1501).
JWH1210, JWH1208
(Even if it attaches a clip in JWH1208
and attaches it in JWH1210,
it is satisfactory.)
A CLASS AMP board
Extension cable (Part No. : J-2501-290-A)
to the E-VOLUME board (CNS1202) and
A CLASS AMP board (CNS1502).
chassis

9
STR-DA3200ES/DG1000
HARNESS SETTING
front panel block
POWER SW board
Please band together so that a ribbon cable
does not approach a primary side
of POWER SW board.
Please band the cable from aVIDEO 3 board
together in this position.
Please band together so that the ribbon cable
from a DIGITAL board cannot touch a heat sink.
DIGITAL
board
heat sink heat sink
Please band together by purse lock
so that a cable cannot touch a heat sink.
Please band together so that a primary side
cable cannot touch a power transformer.
power
transformer
Please band together so that a cable cannot touch
a power transformer and a heat sink.
Please band together so that the ribbon cable (5pin) to AC board
and the ribbon cable (4 pin) from SP TERMNAL board
do not approach the primary side parts of AC board.
SP TERMNAL board
AC board

10
STR-DA3200ES/DG1000 SECTION 2
GENERAL This section is extracted from
instruction manual.
To remove the cover
Press PUSH.
When you remove the cover, keep it out of
reach from children.
Front panel
Name Function
APOWER Press to turn the
receiver on or off.
BAUTO CAL MIC
jack Connects to the supplied optimizer
microphone for the
Digital Cinema Auto
Calibration function.
CTONE MODE Adjusts FRONT BASS
and FRONT TREBLE.
Press TONE MODE
repeatedly to select
BASS or TREBLE,
then turn TONE to
adjust the level.
TONE
DRemote sensor Receives signals from
remote commander.
EMEMORY/
ENTER Press to operate a tuner (FM/AM/XM).
TUNING MODE
TUNING
FCATEGORY
MODE Used when listening to XM Radio.
CATEGORY
+/–
GDisplay
window The current status of theselectedcomponent
or a list of selectable
items appears here.
H2CH Press to select sound
field.
A.F.D.
MOVIE
MUSIC
Name Function
IPOWER PressPOWER (ZONE)
to enable operations in
zone 2. Then press
SELECT, then INPUT
SELECTOR
(qh) to
select a source input
into zone 2.
SELECT
JMULTI CH IN Presstoselect theaudio
input signal from the
component connected
to the MULTI
CHANNEL INPUT
jack.
KHDMI Press to select input
source from the
component connected
to the HDMI IN jack.
LPHONES jack Connects to headphones.
MSPEAKERS
(OFF/A/B/A+B) Press to select A, B, A+B, OFF of the front
speakers.
NVIDEO 3 IN/
PORTABLE AV
IN jack
Connect to a portable
audio/videocomponent
such as a camcorder or
video game.
OMULTI
CHANNEL
DECODING
lamp
Lights up when multi-
channel audio signals
are decoded.
PINPUT
SELECTOR Turn to select the input source to play back.
QMASTER
VOLUME Turn to adjust the volume level of all
speakers at the same
time.
Name Function
Rear panel
AAUDIO INPUT/OUTPUT section
AUDIO IN/
OUT jacks Connects to a tape deck, MD deck or
DAT player, etc.
MULTI
CHANNEL
INPUT jacks
Connects to a Super
Audio CD player or
DVD player with an
analog audio jackfor
7.1 channel or 5.1
channel sound.
PRE OUT jacks Connects to an
external power
amplifier.
BDIGITAL INPUT/OUTPUT section
OPTICAL IN/
OUT jacks Connects to a DVD player, Super Audio
CD player, etc. The
COAXIAL jack
provides a better
quality sound.
COAXIAL IN
jacks
HDMI IN/OUT
jacks Connects to a DVD player, or a satellite
tuner. An image and
the sound are output
to TV or a projector.
L
R
CANTENNA section
FMANTENNA
jack Connects to the FM wire antenna (aerial)
supplied with this
receiver.
AM
ANTENNA
jack
Connects to the AM
loop antenna (aerial)
supplied with this
receiver.
XM
ANTENNA
jack
Connects to the XM
connect-and-Play
antenna (aerial) (not
supplied).
DCOMPONENT VIDEO INPUT/
OUTPUT section
COMPONENT
VIDEO (Y, P
B
/
C
B
, P
R
/C
R
)
INPUT/
OUTPUT
jacks*
Connects to a DVD
player, TV, or a
satellite tuner.
ERS-232C jack
Used for
maintenance and
service.
*Youcanwatchthe selected input image when you
connect the MONITOR OUT jack to a TV.
You can also displaycertainmenusettingsand the
sound field on the monitor when you press ON
SCREEN on the remote.
FControl jack for Sony equipment
and other external components
CTRL S IN/
OUT jacks Connects to Sony TV, DVD player or
VCR with
CONTROL S jack.
TRIGGER
OUT jack Connectstointerlock on/off of the power
supply of other 12V
TRIGGER
compliant
components.
IR REMOTE
IN/OUT jacks Connects an IR repeater.
GVIDEO/AUDIO INPUT/OUTPUT
section
AUDIO IN/
OUT jacks Connects to a VCR or a DVD player etc.
VIDEO IN/
OUT jacks*
S VIDEO IN/
OUT jacks*
HSPEAKERS section
Connects to speakers.
L
R
(DA3200ES: US, Canadian models)

11
STR-DA3200ES/DG1000
You can use the supplied remote RM-AAL003
to operate the receiver and to control the Sony
audio/video components that the remote is
assigned to operate.
RM-AAL003
Remote commander
Name Function
AAV ?/1
(on/standby)
Press to turn on or off the audio/
video components that the
remote is assigned to operate.
If you press the ?/1(B) at the
same time, it will turn off the
receiver and other Sony
components (SYSTEM
STANDBY).
Note
The function of the AV ?/1
switch changes automatically
each time you press the input
button (C).
B?/1
(on/standby)
Press to turn the receiver on or
off.
After pressing ZONE 2 (D),
only the receiver in zone 2 is
turnedon or off with this button.
To turn off all components,
press ?/1and AV ?/1(A) at
the same time (SYSTEM
STANDBY).
DZONE 2 Press to enable zone 2 operation.
ESLEEP Press to activate the Sleep
Timer function and the duration
which the receiver turns off
automatically.
FRECEIVER Press to enable the receiver
operation.
G2CH Press to select a sound field.
A.F.D.
MOVIE
MUSIC
Name Function Name Function
•DVD/VHS combo player
F1: DVD
F2: VHS
TV/VIDEO Press TV/VIDEO and TV (wj)
at the same time to select the
input signal (TV input or video
input).
WIDE Press to select the wide picture
mode.
MACRO1,
MACRO2 Press RECEIVER (6) and then press MACRO 1 or
MACRO 2 to set up the macro
function.
RTOP MENU Press to display the menu or
on-screen guide of the DVD
player on the TV screen. Then
useV/v/B/band toperform
menu operations.
MENU Press to display the menus of
the DVD player on the TV
screen. Then use V/v/B/band
to perform a menu
operations.
NIGHT
MODE Press RECEIVER (6) and then press NIGHT MODE to
activate the NIGHT MODE
function.
INPUT
MODE Press RECEIVER (6) and then press INPUT MODE to
select the input mode when the
same components are
connected to both digital and
analog jacks.
SMUTING Press to activate the muting
function.
HNumeric
buttons Press to –preset/tune to preset stations.
–select track numbers of the
CD player, DVD player or
MD deck. Press 0/10 to
select track number 10.
–select channel numbers of
the VCR or satellite tuner.
–After pressing TV (wj),
press the numeric buttons to
select the TV channels.
IENTER Press to enter the value after
selecting a channel, disc or
track using the numeric buttons.
MEMORY Press to store a tuner station
during tuner operation.
JDISPLAY Press to select information
displayed on the display
window, TV screen of the VCR,
satellite tuner, CD player, DVD
player, or MD deck.
KAfter pressing MENU (qd) or
TOP MENU (qk), pressV/v,B
or bto select the settings. Then
press to enter the selection.
LTOOLS Pressto displayand selectitems
from the option menus for DVD
player, etc.
OPTIONS
V/v/B/b
MMENU Press to display the menu of the
receiver, DVD player, or TV,
etc.
NCATEGORY
+/– Press to select the category for XM Radio.
REPLAY B·/
ADVANCE
·b
Press to replay the previous
sceneorfastforward the current
scene of the VCR or DVD
player.
Om/Ma)
xa)
Xa)
Hb)
./>a)
Press to operate the DVD
player, CD player, MD deck or
tape deck, etc.
CATEGORY
MODE Press to select the category mode for XM Radio.
TUNING +/– Pressto selectstations.
PPRESET
+b)/– Press to register FM/AM/XM
Radiostations or toselectpreset
stations.
TV CH +/– Press TV (wj) and then press
TV CH+/– to operate the TV,
satellite tuner, VCR, etc.
QF1/F2 Press TV (wj) and then press
F1 or F2 to select a component
to operate.
•Harddiskrecorder
F1: HDD
F2: DVD
CInput
buttons Press one of the buttons to select the component you want
to use. To utilize the buttons
with names in pink, press
SHIFT (wg), and then press the
button. When you press any of
the input buttons, the receiver
turns on. The buttons are
factory assigned to control Sony
components. You can program
the remote to control non-Sony
components following the steps
in “Programming the remote”.
TMASTER
VOL +/– Press to adjust the volume level of all speakers at the same time.
TV VOL +/– Press TV (wj) and then press
TV VOL +/– to adjust the
volume level of the TV.
UDISC SKIP Press to skip a disc when using
a multi-disc changer.

12
STR-DA3200ES/DG1000
a)
Se
you can use to control each component.
e the table for information on the buttons that
b)
The tactile dot is attached to these buttons (H,
PRESET+). Use as a mark of operation.
Notes
•Somefunctionsexplained in this section may not
work depending on the model.
•Theabove explanation is intended to serve as an
example only. Therefore, depending on the
component, the above operation may not be
possible or may operate differently than described.
VRETURN/
EXIT OPress to return to the previous menu or exit the menuwhile the
menu or on-screen guide of the
VCR, DVD player, or satellite
tuner is displayed on the TV
screen.
WON SCREEN Press to display the receiver
status. Then, if you press
MENU (qd), the menus of the
receiver appear.
XCLEAR Press to
–clear a mistake when you
press the incorrect numeric
button.
–return to continuous
playback, etc. of the satellite
tuner or DVD player.
>10 Press to select
–tracknumbers over 10 of the
VCR, satellite tuner, CD
player or MD deck.
–channel numbers of the
Digital CATV terminal.
D.TUNING Press to enter direct tuning
mode.
YSHIFT Press to light up the button. It
changes the remote button
function to activate the buttons
with pink printing.
ZA.DIRECT Press to switch the audio of the
selected input to analog signal
without any adjustment.
wj TV Press to enable TV operation.
wk RM SET UP Press to set up the remote.
Name Function
RM-AAU008
Thisremoteisonlyfor zone2operations.
You cannot control the main receiver
directly with this remote.
Operating the main receiver from
zone 2
Name Function
A?/1
(on/standby) Presstoturn a receiver in zone 2
on or off.
BInput
buttons Press one of the buttons to select the component you want
to use. When you press any of
the input buttons, the receiver
turns on. The buttons are
factoryassigned to controlSony
componentsas follows.You can
change the button assignments
following the steps in
“Changing button assignments
(RM-AAU008 only)”.
CMUTING Press to mute the sound.
DMASTER
VOL +/– Press to adjust the volume level for multi zone output.
ERM SET UP Press to change the category of
the buttons.
FRM SET UP
indicator Lights up when data is being sent or when the remote button
assignment is being preset.
GZONE 2 Press to select the command
mode of the remote.
*The setting cannot be changed.
Button Assigned Sony
component
VIDEO 1 VCR (VTR mode 3)
VIDEO 2 VCR (VTR mode 1)
VIDEO 3 VCR (VTR mode 2)
DVD DVD player
TV/SAT TV tuner
TAPE/CD-
RTape deck B
MD/DAT MD deck
SA-CD/CD Super Audio CD/CD
player
TUNER* Built-in tuner
SOURCE The current input
selected for the main
receiver
Operating the components
connected to the main receiver
from zone 2
*Thefunction of these buttons switches
automatically each time you press the input
buttons B. The above explanation is intended to
serve as an example only. Therefore, depending
on the component, the above operation may not
be possible or may operate differently than
described.
Name Function
HOperation
buttons*The following table describes the function of the buttons.
ICH/
PRESET/
D.SKIP
+/–*
Press repeatedly to select a
preset station or channel. When
using a multi-disc changer,
press to skip a disc.
Button(s) Function
NStarts play. (Starts play
on the front side of the
cassette.)
nStarts play on the
reverse side of the
cassette.
XPauses play or
recording, and starts
recording when the
component is in
recording standby.
xStops play.
./>Skips tracks.

13
STR-DA3200ES/DG1000
To remove the cover
Press PUSH.
When you remove the cover, keep it out of
reach from children.
Front panel
Name Function
APOWER Press to turn the
receiver on or off.
BAUTO CAL MIC
jack Connects to the supplied optimizer
microphone for the
Digital Cinema Auto
Calibration function.
Name Function
CTONE MODE Adjusts FRONT BASS
and FRONT TREBLE.
Press TONE MODE
repeatedly to select
BASS or TREBLE,
then turn TONE to
adjust the level.
TONE
EMEMORY/
ENTER Press to operate a tuner (FM/AM).
TUNING MODE
TUNING
FDIMMER Press to adjust
brightness of the
display.
GDISPLAY Press to select
information displayed
on the display.
HSUR BACK
DECODING Press to activate SB DECODING
LMULTI CH IN Presstoselecttheaudio
input signal from the
component connected
to the MULTI
CHANNEL INPUT
jack.
MHDMI Press to select input
source from the
component connected
to the HDMI IN jack.
NPHONES jack Connects to
headphones.
OSPEAKERS
(OFF/A/B/A+B) Press to select A, B, A+B, OFF of the front
speakers.
PVIDEO 3 IN/
PORTABLE AV
IN jack
Connect to a portable
audio/videocomponent
such as a camcorder or
video game.
QMULTI
CHANNEL
DECODING
lamp
Lights up when multi-
channel audio signals
are decoded.
RINPUT
SELECTOR Turn to select the input source to play back.
SMASTER
VOLUME Turn to adjust the volume level of all
speakers at the same
time.
Name Function
J2CH Press to select sound
field.
A.F.D.
MOVIE
MUSIC
KPOWER PressPOWER(ZONE)
to enable operations in
zone 2. Then press
SELECT, then INPUT
SELECTOR
(qk) to
select a source input
into zone 2.
SELECT
DRemote sensor Receives signals from
remote commander.
IDisplay
window The current status of theselectedcomponent
or a list of selectable
items appears here.
Rear panel
AAUDIO INPUT/OUTPUT section
AUDIO IN/
OUT jacks Connects to a tape deck, MD deck or
DAT player, etc.
MULTI
CHANNEL
INPUT jacks
Connects to a Super
Audio CD player or
DVD player with an
analogaudiojackfor
7.1 channel or 5.1
channel sound.
PRE OUT jacks Connects to an
external power
amplifier.
BDIGITAL INPUT/OUTPUT section
OPTICAL IN/
OUT jacks Connects to a DVD player, Super Audio
CD player, etc. The
COAXIAL jack
provides a better
quality sound.
COAXIAL IN
jacks
HDMI IN/OUT
jacks Connects to a DVD player, or a satellite
tuner. An image and
the sound are output
to TV or a projector.
L
R
CANTENNA section
FMANTENNA
jack Connects to the FM wire antenna (aerial)
supplied with this
receiver.
AM
ANTENNA
jack
Connects to the AM
loop antenna (aerial)
supplied with this
receiver.
DCOMPONENT VIDEO INPUT/
OUTPUT section
COMPONENT
VIDEO (Y, PB/
CB, PR/CR)
INPUT/
OUTPUT
jacks*
Connects to a DVD
player, TV, or a
satellite tuner.
ERS-232C jack
Used for
maintenance and
service.
*Youcan watch the selected input image when you
connect the MONITOR OUT jack to a TV.
You can also displaycertain menu settings and the
sound field on the monitor when you press ON
SCREEN on the remote
FControl jack for Sony equipment
and other external components
CTRL S IN/
OUT jacks Connects to Sony TV, DVD player or
VCR with
CONTROL S jack.
TRIGGER
OUT jack Connectstointerlock on/off of the power
supply of other 12V
TRIGGER
compliant
components.
IR REMOTE
IN/OUT jacks Connects an IR repeater.
GVIDEO/AUDIO INPUT/OUTPUT
section
AUDIO IN/
OUT jacks Connects to a VCR or a DVD player etc.
VIDEO IN/
OUT jacks*
S VIDEO IN/
OUT jacks*
HSPEAKERS section
Connects tospeakers
L
R
(DA3200ES: AEP, UK, Taiwan models)

14
STR-DA3200ES/DG1000
You can use the supplied remote RM-AAL004
to operate the receiver and to control the Sony
audio/video components that the remote is
assigned to operate.
RM-AAL004
Remote commander
Name Function
AAV ?/1
(on/standby)
Press to turn on or off the audio/
video components that the
remote is assigned to operate.
If you press the ?/1(B) at the
same time, it will turn off the
receiver and other Sony
components (SYSTEM
STANDBY).
Note
The function of the AV ?/1
switch changes automatically
each time you press the input
button (C).
B?/1
(on/standby)
Press to turn the receiver on or
off.
After pressing ZONE 2 (D),
only the receiver in zone 2 is
turnedon or off with this button.
To turn off all components,
press ?/1and AV ?/1(A) at
the same time (SYSTEM
STANDBY).
CInput
buttons Press one of the buttons to select the component you want
to use. To utilize the buttons
with names in pink, press
SHIFT (wg), and then press the
button. When you press any of
the input buttons, the receiver
turns on. The buttons are
factoryassignedto controlSony
components. You can program
the remote to control non-Sony
components following the steps
in “Programming the remote”.
DZONE 2 Press to enable zone2operation.
ESLEEP Press to activate the Sleep
Timer function and the duration
which the receiver turns off
automatically.
FRECEIVER Press to enable the receiver
operation.
G2CH Press to select a sound field.
A.F.D.
MOVIE
MUSIC
Name Function
HNumeric
buttons Press to –preset/tune to preset stations.
–select track numbers of the
CD player, DVD player or
MD deck. Press 0/10 to
select track number 10.
–select channel numbers of
the VCR or satellite tuner.
–After pressing TV (wj),
press the numeric buttons to
select the TV channels.
IENTER Press to enter the value after
selecting a channel, disc or
track using the numeric buttons.
MEMORY Press to store a tuner station
during tuner operation.
JDISPLAY Press to select information
displayed on the display
window, TV screen of the VCR,
satellite tuner, CD player, DVD
player, or MD deck.
KAfter pressing MENU (qd) or
TOP MENU (qk), pressV/v,B
or bto select the settings. Then
press to enter the selection.
LTOOLS Pressto displayand selectitems
from the option menus forDVD
player, etc.
OPTIONS
MMENU Press to display the menu of the
receiver, DVD player, or TV,
etc.
NREPLAY B·/
ADVANCE
·b
Press to replay the previous
sceneor fastforwardthecurrent
scene of the VCR or DVD
player.
Om/M
a)
x
a)
X
a)
H
b)
./>
a)
Press to operate the DVD
player, CD player, MD deck or
tape deck, etc.
TUNING +/– Press to select stations.
V/v/B/b
QF1/F2 Press TV (wj) and then press
F1 or F2 to select a component
to operate.
•Harddisk recorder
F1: HDD
F2: DVD
•DVD/VHS combo player
F1: DVD
F2: VHS
TV/VIDEO Press TV/VIDEO and TV (wj)
at the same time to select the
input signal (TV input or video
input).
WIDE Press to select the wide picture
mode.
MACRO1,
MACRO2 Press RECEIVER (6) and then press MACRO 1 or
MACRO 2 to set up the macro
function.
RTOP MENU Press to display the menu or
on-screen guide of the DVD
player on the TV screen. Then
useV/v/B/band toperform
menu operations.
MENU Press to display the menus of
the DVD player on the TV
screen. Then use V/v/B/band
to perform a menu
operations.
NIGHT
MODE Press RECEIVER (6) and then press NIGHT MODE to
activate the NIGHT MODE
function.
INPUT
MODE Press RECEIVER (6) and then press INPUT MODE to
select the input mode when the
same components are
connected to both digital and
analog jacks.
SMUTING Press to activate the muting
function.
TMASTER
VOL +/– Press to adjust the volume level of all speakers at the same time.
TV VOL +/– Press TV (wj) and then press
TV VOL +/– to adjust the
volume level of the TV.
UDISC SKIP Press to skip a disc when using
a multi-disc changer.
Name Function
PPRESET
+
b)
/– Press to register FM/AM Radio stations or to select preset
stations.
TV CH +/– Press TV (wj) and then press
TV CH+/– to operate the TV,
satellite tuner, VCR, etc.

15
STR-DA3200ES/DG1000
a)
See the table for information on the buttons that
you can use to control each component.
b)
The tactile dot is attached to these buttons (H,
PRESET+). Use as a mark of operation.
Notes
•Somefunctions explained in this section may not
work depending on the model.
•Theaboveexplanation is intended to serve as an
example only. Therefore, depending on the
component, the above operation may not be
possible or may operate differently than described.
VRETURN/
EXIT OPress to return to the previous menu or exit the menuwhile the
menu or on-screen guide of the
VCR, DVD player, or satellite
tuner is displayed on the TV
screen.
WON SCREEN Press to display the receiver
status. Then, if you press
MENU (qd), the menus of the
receiver appear.
XCLEAR Press to
–clearamistake when you
press the incorrect numeric
button.
–return to continuous
playback, etc. of the satellite
tuner or DVD player.
>10 Press to select
–tracknumbers over 10 of the
VCR, satellite tuner, CD
player or MD deck.
–channel numbers of the
Digital CATV terminal.
D.TUNING Press to enter direct tuning
mode.
YSHIFT Press to light up the button. It
changes the remote button
function to activate the buttons
with pink printing.
ZA.DIRECT Press to switch the audio of the
selected input to analog signal
without any adjustment.
wj TV Press to enable TV operation.
wk RM SET UP Press to set up the remote.
Name Function
RM-AAU008
Thisremote isonlyfor zone2operations.
You cannot control the main receiver
directly with this remote.
CMUTING Press to mute the sound.
DMASTER
VOL +/– Press to adjust the volume level for multi zone output.
ERM SET UP Press to change the category of
the buttons.
FRM SET UP
indicator Lights up when data is being sent or when the remote button
assignment is being preset.
GZONE 2 Press to select the command
mode of the remote.
Operating the main receiver from
zone 2
Name Function
A?/1
(on/standby) Press to turn a receiver in zone2
on or off.
BInput
buttons Press one of the buttons to select the component you want
to use. When you press any of
the input buttons, the receiver
turns on. The buttons are
factory assignedtocontrolSony
componentsas follows.You can
change the button assignments
following the steps in
“Changing button assignments
(RM-AAU008 only)”.
*The setting cannot be changed.
Button Assigned Sony
component
VIDEO 1 VCR (VTR mode 3)
VIDEO 2 VCR (VTR mode 1)
VIDEO 3 VCR (VTR mode 2)
DVD DVD player
TV/SAT TV tuner
TAPE/CD-
RTape deck B
MD/DAT MD deck
SA-CD/CD Super Audio CD/CD
player
TUNER* Built-in tuner
SOURCE The current input
selected for the main
receiver
Name Function
Operating the components
connected to the main receiver
from zone 2
*Thefunction of these buttons switches
automatically each time you press the input
buttons B. The above explanation is intended to
serve as an example only. Therefore, depending
on the component, the above operation may not
be possible or may operate differently than
described.
Name Function
HOperation
buttons*The following table describes the function of the buttons.
ICH/
PRESET/
D.SKIP
+/–*
Press repeatedly to select a
preset station or channel. When
using a multi-disc changer,
press to skip a disc.
Button(s) Function
NStarts play. (Startsplay
on the front side of the
cassette.)
nStarts play on the
reverse side of the
cassette.
XPauses play or
recording, and starts
recording when the
component is in
recording standby.
xStops play.
./>Skips tracks.

16
STR-DA3200ES/DG1000
To remove the cover
Press PUSH.
When you remove the cover, keep it out of
reach from children.
Front panel
Name Function
APOWER Press to turn the
receiver on or off.
BAUTO CALMIC
jack Connects to the supplied optimizer
microphone for the
Digital Cinema Auto
Calibration function.
Name Function
CTONE MODE Adjusts FRONT BASS
and FRONT TREBLE.
Press TONE MODE
repeatedly to select
BASS or TREBLE,
then turn TONE to
adjust the level.
TONE
DRemote sensor Receives signals from
remote commander.
EMEMORY/
ENTER Press to operate a tuner (FM/AM/XM).
TUNING MODE
TUNING
FCATEGORY
MODE Used when listening to XM Radio.
CATEGORY
+/–
GDisplay
window The current status of theselected component
or a list of selectable
items appears here.
H2CH Press to select sound
field.
A.F.D.
MOVIE
MUSIC
JMULTI CH IN Presstoselecttheaudio
input signal from the
component connected
to the MULTI
CHANNEL INPUT
jack.
KHDMI Press to select input
source from the
component connected
to the HDMI IN jack.
LPHONES jack Connects to
headphones.
MSPEAKERS
(OFF/A/B/A+B) Press to select A, B A+B, OFF of the front
speakers.
NVIDEO 3 IN/
PORTABLE AV
IN jack
Connect to a portable
audio/videocomponent
such as a camcorder or
video game.
OMULTI
CHANNEL
DECODING
lamp
Lights up when multi-
channel audio signals
are decoded.
PINPUT
SELECTOR Turn to select the input source to play back.
QMASTER
VOLUME Turn to adjust the volume level of all
speakers at the same
time.
Name Function
IPOWER PressPOWER(ZONE)
to enable operations in
zone 2. Then press
SELECT, then INPUT
SELECTOR
(qh) to
select a source input
into zone 2.
SELECT
Rear panel
AAUDIO INPUT/OUTPUT section
AUDIO IN/
OUT jacks Connects to a tape deck, MD deck or
DAT player, etc.
MULTI
CHANNEL
INPUT jacks
Connects to a Super
Audio CD player or
DVD player with an
analogaudiojack for
7.1 channel or 5.1
channel sound.
PRE OUT jacks Connects to an
external power
amplifier.
BDIGITAL INPUT/OUTPUT section
OPTICAL IN/
OUT jacks Connects to a DVD player, Super Audio
CD player, etc. The
COAXIAL jack
provides a better
quality sound.
COAXIAL IN
jacks
L
R
CANTENNA section
FMANTENNA
jack Connects to the FM wire antenna (aerial)
supplied with this
receiver.
AM
ANTENNA
jack
Connects to the AM
loop antenna (aerial)
supplied with this
receiver.
XM
ANTENNA
jack
Connects to the XM
connect-and-Play
antenna (aerial) (not
supplied).
*Youcan watch the selected input image when you
connect the MONITOR OUT jack to a TV.
You can alsodisplaycertainmenu settings and
the sound field on the monitor when you press ON
SCREEN on the remote.
EVIDEO/AUDIO INPUT/OUTPUT
section
AUDIO IN/
OUT jacks Connects to a VCR or a DVD player etc.
VIDEO IN/
OUT jacks*
S VIDEO IN/
OUT jacks*
FSPEAKERS section
Connectstospeakers.
L
R
DCOMPONENT VIDEO INPUT/
OUTPUT section
COMPONENT
VIDEO (Y, P
B
/
C
B
, P
R
/C
R
)
INPUT/
OUTPUT
jacks*
Connects to a DVD
player, TV, or a
satellite tuner.
HDMI IN/OUT
jacks Connects to a DVD player, or a satellite
tuner. An image and
the sound are output
to TV or a projector .
(DG1000)

17
STR-DA3200ES/DG1000
You can use the supplied remote RM-AAL003
to operate the receiver and to control the Sony
audio/video components that the remote is
assigned to operate.
RM-AAL003
Remote commander Name Function
DZONE 2 Press to enable zone 2 operation.
ESLEEP Press to activate the Sleep
Timer function and the duration
which the receiver turns off
automatically.
FRECEIVER Press to enable the receiver
operation.
G2CH Press to select a sound field.
A.F.D.
MOVIE
MUSIC
Name Function
AAV ?/1
(on/standby)
Press to turn on or off the audio/
video components that the
remote is assigned to operate.
If you press the ?/1(B) at the
same time, it will turn off the
receiver and other Sony
components (SYSTEM
STANDBY).
Note
The function of the AV ?/1
switch changes automatically
each time you press the input
button (C).
B?/1
(on/standby)
Press to turn the receiver on or
off.
After pressing ZONE 2 (D),
only the receiver in zone 2 is
turned on or off with this button.
To turn off all components,
press ?/1and AV ?/1(A) at
the same time (SYSTEM
STANDBY).
HNumeric
buttons Press to –preset/tune to preset stations.
–select track numbers of the
CD player, DVD player or
MD deck. Press 0/10 to
select track number 10.
–select channel numbers of
the VCR or satellite tuner.
–After pressing TV (wj),
press the numeric buttons to
select the TV channels.
IENTER Press to enter the value after
selecting a channel, disc or
track using the numeric buttons.
MEMORY Press to store a tuner station
during tuner operation.
JDISPLAY Press to select information
displayed on the display
window, TV screen of the VCR,
satellite tuner, CD player, DVD
player, or MD deck.
KAfter pressing MENU (qd) or
TOP MENU (qk), pressV/v,B
or bto select the settings. Then
press to enter the selection.
LTOOLS Pressto display and selectitems
from the option menus forDVD
player, etc.
OPTIONS
MMENU Press to display the menu of the
receiver, DVD player, or TV,
etc.
NCATEGORY
+/– Press to select the category for XM Radio.
REPLAY B·/
ADVANCE
·b
Press to replay the previous
sceneorfastforwardthecurrent
scene of the VCR or DVD
player.
Om/Ma)
xa)
Xa)
Hb)
./>a)
Press to operate the DVD
player, CD player, MD deck or
tape deck, etc.
CATEGORY
MODE Press to select the category mode for XM Radio.
TUNING +/– Presstoselectstations.
V/v/B/b
MACRO1,
MACRO2 Press RECEIVER (6) and then press MACRO 1 or
MACRO 2 to set up the macro
function.
RTOP MENU Press to display the menu or
on-screen guide of the DVD
player on the TV screen. Then
useV/v/B/band toperform
menu operations.
MENU Press to display the menus of
the DVD player on the TV
screen. Then use V/v/B/band
to perform a menu
operations.
NIGHT
MODE Press RECEIVER (6) and then press NIGHT MODE to
activate the NIGHT MODE
function.
INPUT
MODE Press RECEIVER (6) and then press INPUT MODE to
select the input mode when the
same components are
connected to both digital and
analog jacks.
SMUTING Press to activate the muting
function.
Name Function
CInput
buttons Press one of the buttons to select the component you want
to use. To utilize the buttons
with names in pink, press
SHIFT (wg), and then press the
button. When you press any of
the input buttons, the receiver
turns on. The buttons are
factory assigned to control Sony
components. You can program
the remote to control non-Sony
components following the steps
in “Programming the remote”.
PPRESET
+b)/– Press to register FM/AM/XM
Radiostations or to select preset
stations.
TV CH +/– Press TV (wj) and then press
TV CH+/– to operate the TV,
satellite tuner, VCR, etc.
QF1/F2 Press TV (wj) and then press
F1 or F2 to select a component
to operate.
•Harddisk recorder
F1: HDD
F2: DVD
•DVD/VHS combo player
F1: DVD
F2: VHS
TV/VIDEO Press TV/VIDEO and TV (wj)
at the same time to select the
input signal (TV input or video
input).
WIDE Press to select the wide picture
mode.
a)See the table for information on the buttons that
you can use to control each component.
b)The tactile dot is attached to these buttons (H,
PRESET+). Use as a mark of operation.
TMASTER
VOL +/– Press to adjust the volume level of all speakers at the same time.
TV VOL +/– Press TV (wj) and then press
TV VOL +/– to adjust the
volume level of the TV.
UDISC SKIP Press to skip a disc when using
a multi-disc changer.
VRETURN/
EXIT OPress to return to the previous menu or exit the menu while the
menu or on-screen guide of the
VCR, DVD player, or satellite
tuner is displayed on the TV
screen.
WON SCREEN Press to display the receiver
status. Then, if you press
MENU (qd), the menus of the
receiver appear.
XCLEAR Press to
–clear a mistake when you
press the incorrect numeric
button.
–returntocontinuous
playback, etc. of the satellite
tuner or DVD player.
>10 Press to select
–tracknumbers over 10 of the
VCR, satellite tuner, CD
player or MD deck.
–channel numbers of the
Digital CATV terminal.
D.TUNING Press to enter direct tuning
mode.
YSHIFT Press to light up the button. It
changes the remote button
function to activate the buttons
with pink printing.
ZA.DIRECT Press to switch the audio of the
selected input to analog signal
without any adjustment.
wj TV Press to enable TV operation.
wk RM SET UP Press to set up the remote.
Notes
•Somefunctions explained in this section may not
work depending on the model.
•Theaboveexplanation is intended to serve as an
example only. Therefore, depending on the
component, the above operation may not be
possible or may operate differently than described.

STR-DA3200ES/DG1000
18
•This set can be disassembled in the order shown below.
3-1. DISASSEMBLY FLOW
Note 1: The process described in can be performed in any order.
Note 2: Without completing the process described in , the next process can not be performed.
SECTION 3
DISASSEMBLY
3-2. CASE
(Page 19)
3-4. S-VIDEO/CIS
BOARD
(Page 20)
3-3. FRONT PANEL
ASSY
(Page 19)
3-7. VIDEO BOARD
(Page 21) 3-5. TUNER
(Page 20)
3-10. POWER
TRANSFORMER (T01)
(Page 23)
3-6. E-VOLUME
BOARD
(Page 21)
SET
3-9. ANALOG BOARD
(Page 22)
3-11. MAIN BOARD
(Page 23)
3-8. SP TERMINAL
BOARD
(Page 22)

STR-DA1200ES/DG1000
19
3-3. FRONT PANEL ASSY
Note: Follow the disassembly procedure in the numerical order given.
3-2. CASE
3 flat head screw
4 case
1 two screws (4 × 8)
2 two flat head screws
1 two screws (4 × 8)
1 connector
(CNP53)
8 two screws
(BVTP3
× 8)
7 five screws
(BVTP3
× 8)
9 front panel assy
6 connector
(CN2014)
5 connector
(CN2016)
4 connector
(CN2015)
3 connector
(CNP6902)
2 connector
(CN606)

STR-DA3200ES/DG1000
20
3-5. TUNER
3-4. S-VIDEO/CIS BOARD
6 connector
(CNP6901)
1 connector
(CN6801)
4 CIS board (DA3200ES)
7 connector
(CNP6902)
9 S-VIDEO board
8 three screws
(BVTP3 × 8)
3 two screws
(BVTP3 × 8)
2 two screws
5 wire (flat type) (15 core)
(CNS6903)
2 three screws
(BVTP3
× 8)
3 tuner
1 wire (flat type) (11 core)
(DA3200ES: US, Canadian, Taiwan/DG1000)
wire (flat type) (15 core) (DA3200ES: AEP, UK)