Sony XT-XM1 - Xm Satellite Radio Tuner User manual

SERVICE MANUAL
XM SATELLITE RADIO RECEIVER
US Model
SPECIFICATIONS
XT-XM1
Ver 1.1 2003.06
9-874-057-02 Sony Corporation
2003F05-1 e Vehicle Company
C2003.06 Published by Sony Engineering Corporation
Notes on chip component replacement
•Never reuse a disconnected chip component.
•Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
Frequency 2332.5 – 2345.0 MHz
Power requirements 12 V DC car battery
(negative ground)
Outputs BUS control output
Audio output
Inputs Antenna input (Satellite,
Terrestrial)
BUS control input
Audio input
Dimensions 224 ×37.8 ×160 mm
(8
7
/
8
×1
1
/
2
×6
3
/
8
in.)
(w/h/d)
Mass Approx. 1.0 kg
(2 lb. 4 oz.)
Supplied accessories Parts for installation and
connection (1 set)
Design and specifications are subject to change
without notice.

2
XT-XM1
POSITION OF THE ID LABEL
The ID label is stuck on the following position.
ABOUT THE MASTER UNIT
This unit is compatible only with the master unit (car audio system compatible with SONY BUS SYSTEM) released year 2000 or after.
Connect the master unit as shown below to activate this unit.
ABOUT TYPE A/B
IC107 of the TRANSLATOR board has been changed in the midway the production.
Part No. of the TRANSLATOR board and instruction manual have been also changed accompanying the above change.
When you repair or replace parts indicated in the table, please be sure to check the serial No..
TRANSLATOR IC701 Instruction
board manual
TYPE A A-3274-400-A 6-801-746-02 3-243-168-12
(Serial No. 128500 or before) MN101C49GYB1
TYPE B A-3274-779-A 6-801-453-01 3-243-168-21
(Serial No. 128501 or after) MN101C49GYG
XT-XM1
master unit
released in year 2000 or after
(compatible with
SONY BUS SYSTEM)
SONY BUS CONTROL OUT SONY BUS CONTROL IN
SECTION 1
SERVICING NOTES
ID label
– SIDEVIEW –
Ver 1.1

3
XT-XM1
SECTION 2
GENERAL This section is extracted from
instruction manual.
Connection
Connectionexample Cautions
•This unit is designed for negative ground 12 V DC operation only.
•Before making connections, turn the car ignition off to avoid short circuits.
• Connect the yellow power input cord only after all other cords have been connected.
• Run all ground leads to a common ground point.
Connectiondiagram
XM Antenna*Sony BUS Compatible
Car Audio*
XT-XM1
CD/MD changer**not supplied
POWER
SONY BUS CONTROL
OUT IN L R L R OUT IN
AUDIO
TER SAT
ANTENNA
Yellow
To a +12 V power terminal which
is energized at all times
Be sure to connect the black ground
lead to it first.
Fuse (3 A)
Black
To a metal point on the car
First connect the black ground lead,
then connect the yellow power input
leads.
CD/MD changer
(not supplied)
Sony BUS Compatible
Car Audio
(not supplied)
4
3
XM antenna
(not supplied)
OUT
OUT
IN
IN
Green Yellow
Connect as the connector
hook facing down
Connect with BUS cable to
the XM Satellite receiver,
aligning the vmarks.
RCA pin cord
(not supplied)
BUS cable
(not supplied)
2
Note
When you use an optional BUS cable, note
that a BUS cable with an 8-pin plug (L-type)
cannot be used because of its shape.
(Curry)
Installingtheunit
•Mount the unit either inside the trunk or under a seat.
•Choose the mounting location carefully so the unit will not interfere with the normal movements of
the driver and it will not be exposed to direct sunlight or hot air from the heater.
•Do not install the unit under the floor carpet, where the heat dissipation from the unit will be
considerably impaired.
First, place the unit where you plan to install it, and mark the positions of the four screw holes on
the mounting surface.
Notes
• Use only the supplied screws.
• Be sure not to damage the fuel tank or brake line with the tapping screws.
Fuse replacement
If the fuse blows, check the power connection and replace the fuse. If the fuse blows again after
replacement, there may be an internal malfunction.
Warning
Use a fuse with the specified amperage rating.
Use of a higher amperage fuse may cause serious damage.
Screw hole:
ø3.3 mm (
5
/ 32 in.)
11

4
XT-XM1 SECTION 3
DIAGRAMS
Note on PrintedWiring Board:
•X: parts extracted from the component side.
•Y: parts extracted from the conductor side.
•: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
3-1. NOTE FOR PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM
Note on Schematic Diagram:
•All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
•All resistors are in Ωand 1/4W or less unless otherwise
specified.
•C: panel designation.
•A: B+ Line.
•Powervoltageisdc14.4Vand fedwithregulateddc power
supply from BATT cords.
•Voltages and waveforms are dc with respect to ground
under no-signal (detuned) and master unit connected
conditions.
no mark : XM
•VoltagesaretakenwithaVOM(Inputimpedance 10MΩ).
Voltage variations may be noted due to normal produc-
tion tolerances.
•Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal produc-
tion tolerances.
•Circled numbers refer to waveforms.
•Signal path.
F: XM
E: AUDIO (AUX)
Caution:
Pattern face side: Partsonthepatternfacesideseenfrom
(Conductor Side) the pattern face are indicated.
Parts face side: Parts on the parts face side seen from
(Component Side) the parts face are indicated.

XT-XM1
55
•IC Block Diagrams
IC103 TA2050F (EL) IC106 BA8272FV-E2
1
2
3
4
5
6
7
89
10
11
12
13
14
15
16 NC
IN(–)1
IN(+)1
IN(+)2
IN(–)2
NC
NC
NC
OUT1
VREF
NC
GND
NC
VCC
NC
OUT2
12 3 45 6 7
89
10
14 13 12 11
VCC BUS ON LINK OFF CLK OUT DATA OUT DATA IN
BUS RESET
BUS DATA
VREF
BUS CLK
GND
BUS ON IN
BUS ON OUT
RESET
RESET
SWITCH
• Waveform
1IC107 qs (OSC2)
2.7 Vp-
p
54 ns
3-2. IC PIN FUNCTION DESCRIPTION
•IC107 MN101C49GYB1 (SYSTEM CONTROLLER)
Pin No. Pin Name I/O Description
1VREF– I Reference voltage (0V) input terminal (for A/D converter)
2 FLASH I Internal flash memory data write mode detection signal input terminal “L”: data write mode
3 to 9 (IN-L) I Not used
10 VREF+ I Reference voltage (+5V) input terminal (for A/D converter)
11 VDD — Power supply terminal (+5V)
12 OSC2 OMain system clock output terminal (18.432 MHz)
13 OSC1 IMain system clock input terminal (18.432 MHz)
14 VSS — Ground terminal
15 XI (VSS) I Sub system clock input terminal Not used
16 XO O Sub system clock output terminal Not used
17 MMOD (VSS) I Memory mode selection signal input terminal Not used
18 TX O IS bus “TXRX” signal output terminal
19 RX I IS bus “TXRX” signal input terminal
20 IS FOUT O IS bus “FRAME” signal output terminal
21 SO O Serial data output to the SONY bus interface
22 SI I Serial data input from the SONY bus interface
23 SCLK O Serial clock signal output to the SONY bus interface
24 GND — Ground terminal
25 LINKOFF O Bus on/off control signal output “L”: bus on
26 BUSON I Bus on/off control signal input from the SONY bus interface “H”: bus on
27 (IN-L) I Not used
28 BU IN I Battery detection signal input terminal “L” is input at low voltage
29 IS FIN I IS bus “FRAME” signal input terminal
30, 31 (IN-L) I Not used
32 VDD2 — Power supply terminal (+5V)
33 X T RESET ISystem reset signal input from the reset signal generator “L”: reset
“L” is input for several 100 msec after power on, then it changes to “H”
34 to 40 (IN-L) I Not used
41 VPP — Power supply terminal (+5V)
42 PC-TX O Not used
43 PC-RX I Not used
44 NC — Not used
45 E2PROM-SCL O Serial data transfer clock signal output to the EEPROM
46 NC — Not used
47 E2PROM-SDA I/O Two-way data bus with the EEPROM
48 to 62 NC — Not used
63 X M-RESET O Reset signal output to the MAIN board “L”: reset
64 X M-STANDBY O Standby signal output to the MAIN board “L”: standby
65 P-ON O +9V power supply on/off control signal output “H”: power on
66 SELECT (H-XM) O Relay drive signal output “H”: XM on
67 X MUTE O Muting on/off control signal output “L”: muting on
68 to 94 NC — Not used
95 DAVSS — Ground terminal (for D/A converter)
96to 99 NC — Not used
100 DAVDD — Power supply terminal (+5V) (for D/A converter)

XT-XM1
66
3-3. PRINTED WIRING BOARD – TRANSLATOR Board (Component Side) –
IC101
IC102
IC107
125
26
50
5175
100
76
IC108
IC105 IC103
IC104
IC106
(COMPONENT SIDE)
TRANSLATOR BOARD
51
1
2
3
SG
D
S
GD
MAIN
BOARD
1-684-839- 11
1 2 3 4 5 6 7 8 9 10 11
A
B
C
D
E
F
G
H
I
D102 H-3
D103 I-5
D104 D-5
D105 D-5
D106 D-5
D107 C-5
D108 C-4
D109 C-6
D110 C-7
D111 C-11
D112 C-11
D113 D-7
D114 C-9
D115 G-11
D116 I-4
D117 C-5
D118 C-5
IC101 H-1
IC102 I-6
IC103 F-10
IC104 G-9
IC105 F-8
IC106 E-5
IC107 H-8
IC108 G-9
Q101 I-3
Q102 I-3
Q103 I-5
Q104 I-5
Q105 D-5
Q106 D-10
Q107 D-7
Q108 E-6
Q109 E-7
Q110 C-9
Q111 I-9
Q112 H-9
Q113 H-10
Q114 D-7
Q115 I-4
•Semiconductor
Location
Ref. No. Location

XT-XM1
77
3-4. PRINTED WIRING BOARD – TRANSLATOR Board (Conductor Side) –
CN105
L
IN
R
CN104
L
OUT
R
AUDIO
(FOR SONY BUS)
IN
(FOR SONY BUS)
OUT
SONY BUS CONTROL
1
2
F1
BATT GND
BLK
YEL
POWER
DC12V
1
2
6
10
5
1
(CONDUCTOR SIDE)
TRANSLATOR BOARD
1-684-839- 11
MAIN
BOARD
1 2 3 4 5 6 7 8 9 10 11
A
B
C
D
E
F
G
H
I
D101 C-11
•Semiconductor
Location
Ref. No. Location

XT-XM1
88
3-5. SCHEMATIC DIAGRAM • See page 5 for Waveform. •See page 5 for IC Block Diagrams. •Refer to “SERVICING NOTES”(Page 2) aboutTYPE A/B.
TP142
Q108
Q110
Q115
R108
R143 R144
R151
R102
TP105
TP106
TP107
TP108
TP109
TP110
TP111
TP112
TP113
TP114
TP120
TP121
C153
C149 C144
X101 R141
R125
C154
C155
R132 TP103
TP104
R127
R126
R142
TP161
TP162
FB101
C147 C150
D101
C101
C103
C148
IC101
R137
TP158
D116
D103
R107
Q103
Q104
R105 R104
Q102
Q101
C104D102
C152 C105
TP156
F101
C106
IC102
R106
TP153 TP155
C108
R130
C119D115
TP152
C114
C113
C143
R139
TP150
R123R124
R121 R122
C142
TP102
TP101
TP160
IC108
TP159
C151
C159
R146
R152
IC105
R128 R129
C102
C109R103
TP157
R110
R150 R149 C158
C139
C156C140 C157 C141
R136
TP149
R135
R131
Q114
R134
R133
C145
TP143
D113
C136
C137R120
R119
C135
Q106
Q107
R117
C133
C134
R118
TP144
D114
TP146
C161
C160
TP141
C129 C120 C121 C122 C123 R112
R113C125
R114
C126
R111C118C117C116C115C132
R116C127
R115
C128
TP126
TP145
TP128
TP129
D112D111
TP122
TP127
TP124
C131
C130
TP123
TP125
D110
D109
IC106
TP151
TP140
TH101
TH102
R109
TP139
C162
C110
TP138
C111
D108
D107
D118
D106
D104
D117
D105
TP137
TP131
TP134
TP135
CN107
CN108
C112
IC103
C138
R101
TP154
CN101
Q109
CN104
Q112
Q111
BP102
BP101
TP148
TP147
IC107
IC104
CN106
CN103
F1
Q113
C107
Q105
TP130
TP133
TP132
CN105
L101
TP136
RY101
2SC2412K
DTC114EKA
DTC114EKA
47k
47k 47k
47k
56k
0.1
10p 10p
18.432MHz 220
220
0.1
100
16V
47k
220
220
0
0.01 10
16V
1N5404TU
0.01
100
16V
0.01
PQO9TZ5U
1k
UDZSTE-1718B
MA8056-H
56k
2SC2412K
2SC2412K
100k 100k
2SC2412K
2SB1202FA
0.1MA8056-H
1000
25V
47
25V
0.01
XC61CN4102MR
47k
1
2.2k
0.01MA8056-H
100
16V
0.01
0.001
100
10k10k
100 100
0.1
RH5RL33AA
0.1
1
47k
47k
TC74VHC125FT
47k 47k
2200
25V
0.147k
10
47k 47k 1
0.1
10
16V
10
16V
10
16V
10
16V
100
10k
0
DTA114EKA
100
1k
1
50V
MA8051-M
100
16V
10
16V
100
100
10
16V
DTC314TK
DTC314TK
47k
0.0001
0.0001
47k
1SS355TE-17
10
16V
10
16V
100p 0.001 0.001 0.001 0.001 100
100k100p
100k
100p
1000.0010.0010.0010.001100p
100k100p
100k
100p
MA8062-M MA8062-M
100p
100p
MA8062-M
MA8062-M
BA8272FV
100
330
25V
0.1
0.0047
MA8160-M
MA8160-M
RB411D
MA8160-M
RB411D
MA8160-M
RB411D
8P
8P
0.001
TA2050F(EL)
10
16V
100k
10P
DTC144EKA
2P
2SK1826
2SK1826
MN101C49GYB1 (TYPE A)
BR24C02FV-WE2
2P
2P
3A
32V
2SD1664
0.047F5.5V
DTA114EKA
2P
SO
SO
SI
SI
SCLK
SCLK
LINK
LINK
BUSON
BUSON
GND
LCH
RCH
GND
GND
GND
STBY
RESET
2345
678910
Vin
ON/OFF
Vout
NC
GND
1
IS TXRX
IS FRAME
O
I
G
BUS ON OUT
BUS ON IN
GND
BUS CLK
VREFF
BUS DATA
BUS RESET
VCC
CLK OUT
DATA OUT
DATA IN
RESET
BUS ON
LINK OFF
L
R
OUT
L
R
IN
AUDIO
GROUND-
ISOLATION
Q106,107
MUTING
MUTING
RELAY
DRIVE
Q108,109,114
CONTROL SWITCH
BUFFER
BUFFER
SYSTEM CONTROLLER EEPROM
A0
A1
A2
GND
VCC
TEST
SCL
SDA
BUFFER
+3.3V
REGULATOR
MAIN
BOARD
POWER
GND
BATT
BATTERY
CHECK
+9V REGULATOR
Q103,104,115
+5V REGULATOR
Q101,102
RESET SIGNAL GENERATOR
G
IO
REGULATOR
+5V
BUS ON/OFF
SWITCH
RESET
NC
BATT
CLOCK
DATA
BUSON
GND
NC
NC
RESET
CLOCK
DATA
BUSON
GND
NC
OUT
IN
SONY BUS CONTROL
FOR
SONY BUS
FOR
SONY BUS
SONY BUS INTERFACE
250µH
MN101C49GYG (TYPE B)
Ver 1.1

9
XT-XM1
SECTION 4
EXPLODED VIEW
•Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.
•Accessories are given in the last of the elec-
trical parts list.
•Refer to “SERVICING NOTES” (Page 2) abut
TYPE A/B.
NOTE:
•-XX and -X mean standardized parts, so they
may have some difference from the original
one.
•Color Indication of Appearance Parts
Example:
KNOB, BALANCE (WHITE) . . . (RED)
↑↑
Parts Color Cabinet's Color
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
11-590-519-21 CORD (WITH CONNECTOR) (BUS)
21-824-067-11 CORD, CONNECTION (WITH CONNECT)
(POWER)
31-824-065-11 CABLE, FLAT (10 CORE)
43-243-165-01 SUPPORT
53-243-163-01 CASE (TOP)
6A-3274-400-A TRANSLATOR BOARD, COMPLETE (TYPE A)
6A-3274-779-A TRANSLATOR BOARD, COMPLETE (TYPE B)
73-243-164-01 CASE (BOTTOM)
81-590-874-11 CORD, CONNECTION (AUDIO CORD)
F1 1-532-731-11 FUSE (BLADE TYPE) (AUTO FUSE) (3A/32V)
#1 7-685-792-04 SCREW +PTT 2.6X6 (S)
#2 7-685-647-14 SCREW +BVTP 3X10 TYPE2 N-S
#3 7-685-862-01 SCREW +BVTT 2.6X6 (S)
F1
not supplied
(main board)
not supplied
#3
#3
#3
#2
#1 #1
#1
#1
#1
1
8
2
3
6
7
4
5
Ver 1.1

10
XT-XM1 SECTION 5
ELECTRICAL PARTS LIST
TRANSLATOR
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
A-3274-400-A TRANSLATOR BOARD, COMPLETE (TYPE A)
A-3274-779-A TRANSLATOR BOARD, COMPLETE (TYPE B)
****************************
7-685-647-14 SCREW +BVTP 3X10 TYPE2 N-S
< CAPACITOR >
C101 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C102 1-107-890-31 ELECT 2200uF 20% 25V
C103 1-107-882-61 ELECT 100uF 20% 16V
C104 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C105 1-107-888-61 ELECT 47uF 20% 25V
C106 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C107 1-125-701-11 DOUBLE LAYER 0.047F 5.5V
C108 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V
C109 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C110 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C111 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C112 1-115-416-11 CERAMIC CHIP 0.001uF 5% 25V
C113 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C114 1-107-882-61 ELECT 100uF 20% 16V
C115 1-115-416-11 CERAMIC CHIP 0.001uF 5% 25V
C116 1-115-416-11 CERAMIC CHIP 0.001uF 5% 25V
C117 1-115-416-11 CERAMIC CHIP 0.001uF 5% 25V
C118 1-115-416-11 CERAMIC CHIP 0.001uF 5% 25V
C119 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C120 1-115-416-11 CERAMIC CHIP 0.001uF 5% 25V
C121 1-115-416-11 CERAMIC CHIP 0.001uF 5% 25V
C122 1-115-416-11 CERAMIC CHIP 0.001uF 5% 25V
C123 1-115-416-11 CERAMIC CHIP 0.001uF 5% 25V
C125 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C126 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C127 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C128 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C129 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C130 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C131 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C132 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C133 1-137-503-11 MYLAR 0.0001uF 5% 50V
C134 1-137-503-11 MYLAR 0.0001uF 5% 50V
C135 1-104-951-11 ELECT 10uF 20% 16V
C136 1-107-882-61 ELECT 100uF 20% 16V
C137 1-104-951-11 ELECT 10uF 20% 16V
C138 1-104-951-11 ELECT 10uF 20% 16V
NOTE:
•Due to standardization, replacements in the
parts list may be different from the parts speci-
fied in the diagrams or the components used
on the set.
•-XX and -X mean standardized parts, so they
may have some difference from the original
one.
•RESISTORS
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable
•Refer to “SERVICING NOTES” (Page 2)
about TYPE A/B.
•Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when order-
ing these items.
•SEMICONDUCTORS
In each case, u: µ, for example:
uA. . : µA. . uPA. . : µPA. .
uPB. . : µPB. . uPC. . : µPC. .
uPD. . : µPD. .
•CAPACITORS
uF: µF
•COILS
uH: µH
When indicating parts by reference
number, please include the board.
C139 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C140 1-104-951-11 ELECT 10uF 20% 16V
C141 1-104-951-11 ELECT 10uF 20% 16V
C142 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C143 1-115-416-11 CERAMIC CHIP 0.001uF 5% 25V
C144 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V
C145 1-104-942-11 ELECT 1uF 20% 50V
C147 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C148 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C149 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V
C150 1-104-951-11 ELECT 10uF 20% 16V
C151 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C152 1-107-914-11 ELECT 1000uF 20% 25V
C153 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C154 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C155 1-107-882-61 ELECT 100uF 20% 16V
C156 1-104-951-11 ELECT 10uF 20% 16V
C157 1-104-951-11 ELECT 10uF 20% 16V
C158 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V
C159 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V
C160 1-104-951-11 ELECT 10uF 20% 16V
C161 1-104-951-11 ELECT 10uF 20% 16V
C162 1-128-527-11 ELECT 330uF 20% 25V
< CONNECTOR >
*CN101 1-779-124-11 HOUSING, CONNECTOR 10P
*CN103 1-750-140-11 PIN, CONNECTOR (PC BOARD) 2P (POWER)
CN104 1-565-319-71 JACK, PIN 2P (AUDIO OUT)
CN105 1-565-319-71 JACK, PIN 2P (AUDIO IN)
CN106 1-764-101-11 PIN, CONNECTOR (PC BOARD) 2P
CN107 1-580-907-31 PLUG, CONNECTOR
(SONY BUS CONTROL IN)
CN108 1-580-907-31 PLUG, CONNECTOR
(SONY BUS CONTROL OUT)
< DIODE >
D101 8-719-049-38 DIODE 1N5404TU
D102 8-719-977-03 DIODE DTZ5.6B
D103 8-719-977-03 DIODE DTZ5.6B
D104 8-719-975-40 DIODE RB411D
D105 8-719-975-40 DIODE RB411D
D106 8-719-022-90 DIODE MA8160M
D107 8-719-022-90 DIODE MA8160M
D108 8-719-022-90 DIODE MA8160M
Ver 1.1

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
11
XT-XM1
TRANSLATOR
D109 8-719-422-64 DIODE MA8062-M
D110 8-719-422-64 DIODE MA8062-M
D111 8-719-422-64 DIODE MA8062-M
D112 8-719-422-64 DIODE MA8062-M
D113 8-719-420-90 DIODE MA8051-M
D114 8-719-988-61 DIODE 1SS355TE-17
D115 8-719-977-03 DIODE DTZ5.6B
D116 8-719-083-66 DIODE UDZSTE-1718B
D117 8-719-022-90 DIODE MA8160M
D118 8-719-975-40 DIODE RB411D
< SHORT >
F101 1-216-295-00 SHORT CHIP 0
< FERRITE BEAD >
FB101 1-414-235-22 FERRITE 0uH
< IC >
IC101 8-759-182-88 IC PQ09TZ5U
IC102 8-759-828-22 IC XC61CN4102MR
IC103 8-759-262-37 IC TA2050F (EL)
IC104 8-759-643-31 IC BR24C02FV-WE2
IC105 8-759-524-04 IC TC74VHC125FT (EL)
IC106 8-759-697-48 IC BA8272FV-E2
IC107 6-801-746-02 IC MN101C49GYB1 (TYPE A)
IC107 6-803-453-01 IC MN101C49GYG (TYPE B)
IC108 8-759-444-93 IC RH5RL33AA-T1
< COIL >
L101 1-419-476-11 COIL, CHOKE 250uH
< TRANSISTOR >
Q101 8-729-019-03 TRANSISTOR 2SB1202FA-T-TL
Q102 8-729-120-28 TRANSISTOR 2SC1623-L5L6
Q103 8-729-120-28 TRANSISTOR 2SC1623-L5L6
Q104 8-729-120-28 TRANSISTOR 2SC1623-L5L6
Q105 8-729-027-23 TRANSISTOR DTA114EKA-T146
Q106 8-729-920-21 TRANSISTOR DTC314TK-T-146
Q107 8-729-920-21 TRANSISTOR DTC314TK-T-146
Q108 8-729-120-28 TRANSISTOR 2SC1623-L5L6
Q109 1-801-806-11 TRANSISTOR DTC144EKA
Q110 8-729-900-53 TRANSISTOR DTC114EK
Q111 8-729-037-55 FET 2SK1826 (TE85L)
Q112 8-729-037-55 FET 2SK1826 (TE85L)
Q113 8-729-920-85 TRANSISTOR 2SD1664-QR
Q114 8-729-027-23 TRANSISTOR DTA114EKA-T146
Q115 8-729-900-53 TRANSISTOR DTC114EK
< RESISTOR >
R101 1-216-845-11 METAL CHIP 100K 5% 1/10W
R102 1-218-889-11 METAL CHIP 56K 0.5% 1/10W
R103 1-218-887-11 METAL CHIP 47K 0.5% 1/10W
R104 1-216-845-11 METAL CHIP 100K 5% 1/10W
R105 1-216-845-11 METAL CHIP 100K 5% 1/10W
R106 1-216-841-11 METAL CHIP 47K 5% 1/10W
R107 1-218-889-11 METAL CHIP 56K 0.5% 1/10W
R108 1-216-841-11 METAL CHIP 47K 5% 1/10W
R109 1-216-809-11 METAL CHIP 100 5% 1/10W
R110 1-216-797-11 METAL CHIP 10 5% 1/10W
R111 1-216-809-11 METAL CHIP 100 5% 1/10W
R112 1-216-809-11 METAL CHIP 100 5% 1/10W
R113 1-216-845-11 METAL CHIP 100K 5% 1/10W
R114 1-216-845-11 METAL CHIP 100K 5% 1/10W
R115 1-216-845-11 METAL CHIP 100K 5% 1/10W
R116 1-216-845-11 METAL CHIP 100K 5% 1/10W
R117 1-216-841-11 METAL CHIP 47K 5% 1/10W
R118 1-216-841-11 METAL CHIP 47K 5% 1/10W
R119 1-216-809-11 METAL CHIP 100 5% 1/10W
R120 1-216-809-11 METAL CHIP 100 5% 1/10W
R121 1-216-809-11 METAL CHIP 100 5% 1/10W
R122 1-216-809-11 METAL CHIP 100 5% 1/10W
R123 1-216-833-11 METAL CHIP 10K 5% 1/10W
R124 1-216-833-11 METAL CHIP 10K 5% 1/10W
R125 1-216-813-11 METAL CHIP 220 5% 1/10W
R126 1-216-813-11 METAL CHIP 220 5% 1/10W
R127 1-216-813-11 METAL CHIP 220 5% 1/10W
R128 1-216-841-11 METAL CHIP 47K 5% 1/10W
R129 1-216-841-11 METAL CHIP 47K 5% 1/10W
R130 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R131 1-216-864-11 SHORT CHIP 0
R132 1-216-841-11 METAL CHIP 47K 5% 1/10W
R133 1-216-821-11 METAL CHIP 1K 5% 1/10W
R134 1-216-809-11 METAL CHIP 100 5% 1/10W
R135 1-216-833-11 METAL CHIP 10K 5% 1/10W
R136 1-216-809-11 METAL CHIP 100 5% 1/10W
R137 1-216-821-11 METAL CHIP 1K 5% 1/10W
R139 1-216-809-11 METAL CHIP 100 5% 1/10W
R141 1-216-813-11 METAL CHIP 220 5% 1/10W
R142 1-216-864-11 SHORT CHIP 0
R143 1-216-841-11 METAL CHIP 47K 5% 1/10W
R144 1-216-841-11 METAL CHIP 47K 5% 1/10W
R146 1-216-841-11 METAL CHIP 47K 5% 1/10W
R149 1-216-841-11 METAL CHIP 47K 5% 1/10W
R150 1-216-841-11 METAL CHIP 47K 5% 1/10W
R151 1-216-841-11 METAL CHIP 47K 5% 1/10W
R152 1-216-841-11 METAL CHIP 47K 5% 1/10W
< RELAY >
RY101 1-755-060-21 RELAY
< THERMISTOR >
TH101 1-801-792-21 THERMISTOR, POSITIVE
TH102 1-801-792-21 THERMISTOR, POSITIVE
< VIBRATOR >
X101 1-781-294-21 VIBRATOR, CRYSTAL (18.432MHz)
**************************************************************
Ver 1.1

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
12
XT-XM1
MISCELLANEOUS
**************
11-590-519-21 CORD (WITH CONNECTOR) (BUS)
21-824-067-11 CORD, CONNECTION (WITH CONNECT)
(POWER)
31-824-065-11 CABLE, FLAT (10 CORE)
81-590-874-11 CORD, CONNECTION (AUDIO CORD)
F1 1-532-731-11 FUSE (BLADE TYPE) (AUTO FUSE) (3A/32V)
************************************************************
ACCESSORIES
************
3-243-168-12 MANUAL, INSTRUCTION (ENGLISH) (TYPE A)
3-243-168-21 MANUAL, INSTRUCTION (ENGLISH) (TYPE B)
************************************************************
PARTS FOR INSTALLATION AND CONNECTIONS
**************************************
501 7-685-662-79 SCREW +BVTP 4X14 TYPE2 IT-3
502 1-824-067-11 CORD, CONNECTION (WITH CONNECT)
(POWER)
503 1-590-519-21 CORD (WITH CONNECTOR) (BUS)
504 1-590-874-11 CORD, CONNECTION (AUDIO CORD)
F1 1-532-731-11 FUSE (BLADE TYPE) (AUTO FUSE) (3A/32V)
F1
POWER CORD
×1
501
504
502
ø4 ×14 mm
×4
505
AUDIO CORD
×1
BUS CABLE
×1
Ver 1.1

13
XT-XM1
MEMO

XT-XM1
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.
Ver. Date Description of Revision
1.0 2002.05 New
1.1 2003.06 Addition of New/Former types (TYPE A/B) accompanying change of
IC107. (ENG-03007)