Sony Effio E User manual

Sony Effio E Surveillance Camera
(BaUt-ia OSD)
USER' S MANUAL
Applicable for: Standard Cameras, Dome Cameras, WaterproofiR
Cameras
Thank you for purchasing
our products. Please read the
manual carefully before operating
Version: 412710V01 9#

Safety Precaution
Note , To avoid thunder-strking. please don\ open the backcover .
tile ma i ntenance must be made by oor autllorized serviceman .
A This symbol means that there might exist uninsulated
dangerous voltage inside the case, be careful
of electric shock.
A This symbol reminds you to pay attention to important
operation and maintenance instmc
ti ons in the accompanied
information.
Warning
~ n order to prevent damage caused by fire or electric
s ho~k . please do. not put cameras exposed in the moi st
envrronment or ramwater.
)> Please make sure the adapter is consistent with produ ct
wccifications, otherwise it might cause ftre, electric shock or damage.
:;> Pay attention to polarity of the adapter, it mi ght cause
some accidents like fires.
~ Please don 't connect multiple ca meras with the same
adapter at the same time; overfoading
of adapter capacity
rnay cause fires.
:;> Power supply must be fimlly fixed so as not to loose to
cause fires.
~ If the device gets " abnonnal smell or smoke", please
stop it immediately and contact with our customer service
center.
~ If the camera doesn't work as usual, please do not
dismantle it by yo
ur se lf. Please contact our local distributor
or our maintenance office authorized by our company,
otherwise we won't promise warranty.
~ Please_ do not splash water on the product components
when clearnng.
Page3of25

Notes
l' Do not make the products under great impact or stay away from
strong electromagnetic interference and vibration.
l' There are some sophisticated parts in side the camer a, therefo re ,
during transportation and installation, please avoid the damage cause
by stress or severe vibration. For the sake of safety, please do not
switch on power before accomplishing all installation.
l' Please com pl y with all electrical safety standards during
operation, camera or signal transmission cable should mainta in a
sufficient distance (50 meters) with high-voltage equipment or cables,
if necessary, lighting and thunder protective measures must be taken.
l' Please in stall the camera in well-ventilated environment.
)' Please do not make the camera face sunsh in e or other strong light
directly
in case of any damage to the lens and the sensor.
)> The temperature and humidity range for caweras work are -l 0 -
50 ·c, less than 95% separately, please do not start cameras beyond
this range.
l' To avoid li ghtning strikes, please ma ke sure the insta ll ation of
power supply ground line in a good condition.
> To prevent the equipment from damage by shower or splash of
water, please do not place the device substances such as liquid.
Page4of25

Contents
I , Features............................ .. ....... .. .......... .. .......................6
ll , lnterfaceFunction Introduction. .. .................. .. .. .. ...........8
2.1 Interface Function Description .............. .. ................8
ill, OSD................................................................ .... . .. ........9
3. l Lens type ...............................................................1
0
3.2 ShutterI AGC ........................................................10
3.3 White Balance........................................................ l2
3.4 Backlight compensation......................................... 13
3.5 Image adjustrnent.......................... .. ....................... l3
3.6Adaptive Tone Reproduction ............ .. ...................14
3.7
Motion ZoneTest........................................... .. ...... 14
3.8 Privacy zone .......................................................... 16
3.9 Day/Night ....................................... .. .....................!?
3.10NR ...................................................... .. ................ 20
3.11 Camera identification code ............ .. ....................21
3.12 Synchronous Mode..............................................
22
3.13 Languages.............................................. .. ............22
3.14 Camerareplacement..........................................
.. 22
3.15 Return to the previous page.................................22
3.16 Exit/Save...........................................................22
IV, Technical Specification ...............................................23
V, FAQ ............................................................................25
Page5of25

I , Features
l, SONY CCD New Generation SONY CCD
Adopting the latest Second-generation high-sensitive CCD and
DSP, it can receive clear and lucid images even at circumstances wi th
very low illumination.
2, Hi-resolution Video Resolution
Color horizontal resolution can reach 700TVL, 8/W horizontal
resolution reach 730TVL.
3, Day & NightSwitch
Day & Night cameras can switch automatically into col or or 8/W
according to optical change~ . When the envirorunent gets down
gloomily, the new generation day & night camera uses new
generation's original installation magnetism valve type infrared optical
filter, will replace automatically for the transparent optical filter. The
camera will automatically cut
over for clean, sharp black-and-white
images.
4, Wide DynamicTechnology
The dynamic camera expands the picture applicable scope, used
the state-of-art science and technology, the effecti
ve technology which
is mainly used in simultaneously photographing when building interior
and window spots. Using this kind
of technology is able to display
indoor and the outdoor picmre simultaneously & clearly.
5, 2 Digital noise reduction technology
In the camera solidifies the digital noise reduction function
toughed, strengthened the signal-to-noise ratio (SIN) and the image
clarity, thus the camera can get clear, sharp images under the low
li ght
environment.
6, MD Multi-districtestablishment function
When the user is monitoring, the day and night camera monitor
any object on the screen starting to move, will transmit an alarm
immediately to the monitoring equipment, causes the user attention the
object which moves on screen. The new generation day & night camera
has the multi-region migration detection establishment function, and
has sensitivity multiple establishments for move detection. Any motion
object, at any time even there is no place
to run away. The subtle points
appears completely. Page6of25

7, (PRIVACY) PRIVACY ZONES multi-district establishment
function
To carry on the privacy protection in the public reg io n, stemming
from the protection by the monitoring either the environment privacy,
some special areas orthe phantom will camouflage through the privacy
the black block to camouflage the image, achieves the privacy
protection goal.
With the new generation day & night camera, the user may
establish easily the privacy position and size to camouflage the black
block. The camera developed many privacy for the user to
camouflage the black block specially, caused the privacy protection
question in each kind of situation monitoring becomes easy, simple.
8, OSD control simply & conveniently
The new generation day and night camera has disposed the
function rich menu completely, all cameras operations complete
completely by the demonstration on monitoring device's menu relaxed
debugging. The user carry on superior performance establishments at
the greatest degree, conveniently. Thus the camerahas been guaranteed
with highest quality picture effect.
Page7of25

II , Interface Function Introduction
2.1 lntertace Function Description
UP
•
• •
L EFT
R IGH T
ENTER This key is Ent
er key, used to enter and exit the me nu
operations, wh ich needs to determine.
UP/DOWN With
the UP and DOWN cursorkeys to move up and
down themenu options.
LEFT !RIGHT With the LEFT. RJGHT keys
mo ve around and modify
the para
me ters of the ac tivities of the menu options.
Page8of25

III, OSD
Press ~e "OK" burton for 2 seconds, the camera will pop up the
main menu system (Figure 1)
SETUP MENU
LENS
SHlJITER!AGC
WliiTEBAL
BACKLIGHT
P!CTADJUST
ATR
MOTIONDET
NEXT ..J
EXIT .J
SETUP ME:-N
PRJVACY
DAY/NI GHT
NR
CAMERA fD
SYNC
LANGUAGE
CAMERA RESET
BACK
£XJT
MANUAL
AUTO
ATW
()f.' f.'
.J
OFF
ON
SAVE ALL
OFF
:_J' TO
OF F
! NT
ENG US II
SAVEALL
Page9of25

3.1 Lens type
There are 2 types of lenses, respectively: DC lens (DC drive lens),
video camera (manual lens). Users can select the lens type according to
the using the camera. Press the "left" or "right" button on to choose the
lens.
Wh en select the auto iri s, should choose "Auto" file; users can
adjust
th e "speed" val ue to-adju st the open speed of auto iris. The value
small
er , th e speed of opening the iris is lower; the value bigger, the
speed is
fa ste r.
AUTO IRIS
TYPE
MODE
SPEED
RETURN
3.2 Shutter I AGC
DC
AUTO
0--255
Move the cursor to "Shutter I AGC"; press the "OK" button to
enter the Shutter I AGC sub-me
nu . Shutter/AGC has two sub-menus:
"Automatic". "Manual". Press left-right key, and then press the Enter
key to enter sub-menu
to se t the relevant parameters.
Pagel0of25

AOTU SETUP
HIGHT LUMINANCE
MODE AUTO IRIS
BRIGHTNESS 0---------------255
LOW LUMINANCE
MODE AG C
BRIGHTNESS x0.50
RETURN
High brightness mode has the two choices: "automatic shutter +
auto iris, auto iris". User can select according to the lens equipped
correspondingly. When using a fixed lens, user must select "Auto
Shutter + auto iris" mode. When using auto iris len s, user must select
the "Auto
lr is" mode.
Brightness can be set between 0-255. User can
adj us t the
brightness
of the overall picture, the smaller the value, the darker the
screen, the greater the value, the brighter the picture.
Low brightness mode, automatic gain has two options: on and
off .
Select the brightness between the 0.25-l to match the appropriate gain
factor.
Use can choose brightness between 0.
25 - 1, the smaller the value,
the darker the screen, illumination worse, greater value, the brighter the
picture, the higher illumination.
Pagellof25

3.4 Backlight compensation
Backlight mode
In the "Backlight Compensation" menu, press the "left" "r ight" to
select "Backlight compensation, brightness compensation, closed".
Users can select the appropriate backlight mode, accord
in g to the
actual need
s.
3.5 Image adjustment
PICT ADJUST
MIRROR
BRIGHTNESS
CONTRAST
SHARPNESS
HUE
GAIN
RETURt'J ~
OFF
0-255
0-255
0-255
0-255
0-255
The mirror has two options: On and off. Opening time: image is
horizontal mirror,
off time: the image is normal. Brightness, contrast,
sharpness value can choose between 0-255. The color tone is also the
real color
of the image color. Users can choose the real colors between
0-255. Gain is
of the screen color depth, 0-255 optional. The sma ll er
the value, the color is
li ghter; the greater value, the more concentrated
co lor.
Page13of25

3.6 Adaptive Tone Reproduction
The ATR (Adaptive Tone Reproduction) function provides
gradation compen
sat ion to improve the contrast of subjects whose
gradation has been lost in cases where, for instance, both
low-luminance areas and high-luminance areas exi
st in the same
picture.
ATR
LUMINANCE
CONT RMT
R.ETUlU-1 ..J
LOW
LOW
Brightness and contrast values can be chose between the "low,
medium, high", User can choose an appropriate value to achieve the
best image quality.
3.7 Motion Zone Test
In th e " Motion Zone Test " menu, press the "left" "rig ht " to select
"On". At this point the image wiU open the motion detection. Then,
click. "OK" button to enter the " Motion Zone
Te st" setting sub-menu,
to set the detect range and sensitivity settings.
MOTION DET
DETECT
SENSE 0-1 27
BLOCK D!SP
ON
MONITOR AREA ON
AREA SEL 1/4
TOP 0-288
BOTIOM 0-288
LEFT
0-468
RJGHT
RETURN _.J
0-468
Pa ge l4 ot25

Back
When the sen tp is complete, press the "up" and "down" key to
move the cursor to the "Back". Then, click "OK" button to return to the
implementation for the appropriate ftmctions.
3.8 Privacy zone
In the "privacy shield" menu, press the "left" "right" to select
"On". At this point the image will open the Privacy masking. Then,
click "OK" to enter "privacy shield" setting sub-menu, you can mask
the scope
of privacy and sensitivity settings.
PRJVACY
AREA SEL
TOP
DOWN
LEFT
RIGHT
COLOR
TRANSP
MOSAIC .J
RETURN
Region Selection
l/ 4
0-288
0-288
0-468
0-468
0-8
1.00
OFF
Select the privacy zone region, and set the related zone, there are
four available setting zones.
Pagel6of25

DAY/N1GHT
BURST OFF
DELAY CNT 0-255
DAY -NIGHT 0-255
NIGHT-
[HV
RETURN .J
0-255
Back Back
Pulse burst signal: on and off, two options.
Delay Control
With this setting the camera achieves the delay time of the
transferr
in g: color to black/white or black/white to color. Conversion
between the colors
is through controll.ing of the camera's brightness
sensor
of the scene. When the light is at critical time, th e camera may
switch the modes back and forth between color and black/white.
Setting the delay time function can resolve this problem. When the
camera senses the light intensity during this period are in line with the
color conversion before the conversion feature, or do not perform.
It is also in tend ed to better protect the camera and allows users to
have better image quality.
Day--Night setting
Set the initiate level of the camera's color/black switch, 0-255
adjustable.
Night-Day setting
Set the end l ev el of the camera's black/color switch, 0-255
Pagel8of25

adjustable.
Note: Set the "Day - Night Set" and "Night -Day set" is to
prevent the frequent changes
in light caused by switching the camera
has been
in a state of users. On the choice of the value, do not set to the
same value. The same value will lead to frequent switch under the light
intensity changing.
Bac k
When t he setup is com pl et e, press the "up" and "down" key to
move the cursor to the "Back". Then click "OK" burton, perform t he
back function.
( I) Color Mode
In the "night switch" menu, press the "left" "right" key to select
"colormodel". At this point the image color mode will be enforced.
Users can setth is funct ion according to actual needs.
(2) Black/White Mode
In the "night switch" menu, press the "left" "right" key to select
"black and white model". At this time. the image will be enforced as
black and white
mo d e. Then, click "OK" burton to enter tbe "black and
white mode" submenu, to set the co~espond in g pa rameters.
B/W
BURST
1
RETURN_..
OFF
Pagel9of25

CI ) Pulse
Set the pulseswitch. the default value: Off.
3.10 NR
Tn the "noise reduction" menu click "OK " button to enter the
"n oise reduction" sub-menu, you can set the cor re sponding pa rameters.
No i se reduction is in the case of very l ow light reduction caused
by low-light point
of the picture noise to enhance the signal to noise
ratio (S I N) and image clarity, and the camera
in low light conditions
catch
es clearly sharpness image, the quality can be guaranteed.
NR
NR MODE
Y LEVEL
C LEVEI.J
RETURN
Y/C
0-15
0-15
Set the noise reduction mode, Y I C, Y, C, off four options. Choose
noise reduction corresponds
to the modes.
Select Y I C mode. you can adjust the value
of brightness and
color in noise reduction between 0-15.
The larger the value, the smaller
th e noise is.
SelectY mode,
yo u can adjust theY level value decomposition.
Select C mode, you c
an adjust tl1e C level value decomposition.
Page20of25

Back
When t he set up complete, click "OK" button to return to the
implementation for the appropriate functions.
3.11 Camera identification code
Ln the "functional camera code" menu, press the "left" "right" to
select "On" At this point the camera image wi
ll display the name of
executive function. Click "OK" button to enter the "camera code"
setting sub-menu, you can set the camera name.
CAMERA lD
ABCDEFGH!JKLMNOPQRSTUV
WXYZ0 123456789- ! "II % $&
() -- · Y," (=) ? @\ t. x .,./
CHR l CHR Z
-11- CLR POS.J
RET U Rl'< .J
You can set the camera code as numbers, uppercase letters, and
related symbols. The length of the names is 15 characters.
"Clear" is for removing the camera name.
"Location" name for the set position. Through the "up, down, left,
right" mobile name location, to determine a good location, then press
"OK" button to return the name of the Edit menu.
"Return" is the end of the name ed it to return to the previous menu.
Page21oi25

3.12 Synchronous Mode
Synchronized pattern default for internal synchronization
3.13 Languages
Chinese, Japanese, English, French, Russian, Ge rm an , Spanish,
Portuguese eight language selections.
3.14 Camera replacement
Chooses this item, then presses confinns the key, all parame te rs
will restore the leaving the plant default value.
3~ 15 Return to the previous page
After establishing completes, according to "on", "under" the key
the cursor moves "returns the previous page",
pr es ses aga in
"detennines" in the key execution corresponding returns the frrst-level
menu.
3.16 Exit/Save
After the parameter establishment completes, when it needs to
preserve, according to "on", "under" the key
mo ves the cursor "t he
withdrawal", according to left, the right key choice "the preservation"
presses "determines" the key, moves "the withdrawal'' to press aga in
confim1s the key, the withdrawal menu.
Pa ge22of25

PRIVACY L- 8 Zones
Privacy Zone Co l or
Color 0- Colo r 7 optional
WDR
Off/On!Auto
WDR Sensitivity o- to adjustable
Motion Detection On I
Off (multi-sensitivity settings, alarm ti me
optional)
Alarm Display leon
AWB
ATW, PUSH, US ER I, USER2,
ANTI CR .
MAt'IUAL or PUSH LOCK
!mage Freeze
On/Off
Special Rotation/ up-sidedown /M irror/ Off
Sharpness 0- 49 adjustable
GAMMA
0.3- LO adjustable
DNR 2DDNR
RS-485 Remote control Support
Comm unicationAdd. 1-254 optional
BPS baudrate 2
400/9600/14400/19200/38400
Control Prot ocol Pelco-D
Video Output
BNCmethod
Power Supply DC12V/AC24V (optional)
Po wer consumption
2.0W
Operation Temperature -
to"c - +so
0c
Page24of25

V, FAQ
1. Q: No image after installation?
a. Ch
eck to connect the power supply correct ly , whether the
indicating led is always
on or not;
b.
Check the video cable, make sure it is workable.
c.
Check if the monitor has been open.
2. Q: Image interference after installation
a. Check the power quality, if the adapter can 't work, please
replace another one.
b.
Check if electromagnetic interference ex i sts in the surroundings,
please use some anti-interference devices.
3.
Q: RS485 can't control menu?
a. Please
check the controller issued code is correct;
b. Please check
if the control circuit is smooth;
c. Please verify the corrununication address. baud rate
we ll-matched;
d.
Pl ease check if the connection interface is loose.
4. Q: Camera image
can't switch into B/W at night?
Please open the camera me nu to see if "Day/Night Switch" is set
as AUT O, if not, please change into AUTO .
5. Q: No ise is ve1y obv ious at night with low illumination.
please make sure
AGC ON .
6. Q: The image color is abnormal.
a. please make sure
if the white balance is cor rectly set as Auto
White Balance.
b. Please enter the menu to restore factory settings.
7. Q: Image appears to be whiter than usual after
in sta llat ion?
a.
Pl ease check whether the lens aperture was adjusted too large,
so
that the i mage appears whiter.
b.
Pl ease ve ri fy the came ra rear panel, if the regulat or
potentiometer is adjusted too large.
c. Check
if the bri gh tness of the monitor is too large.
8. Q: When installation, ima
ge is not clear or ex ist dark corners?
a. Please adjust focus
and zoom of the lens. Make sure the focus
sh
ou ld be adjusted in a proper way.
b. Please check if t he lens is clean.
Page25ot25