Sony OVER 650TVL SERIES User manual

SERVICE MANUAL
1/3” SONY DSP COLOR CCD CAMERA
OVER 650TVL SERIES
V.2E7W_M
The serial number of this product may be found
on the bottom of the unit.
You should note the serial number of this unit in
the space provided and retain this instruction as a
permanent record of your purchase to aid
identification in the event of theft.
Model No.
SerialNo.

▲Before attempting to connect this product, please read and keep this
manual for future use.
Safety Warning
1. Do not open the cover, it may cause electric shock.
Ask a qualified service person for maintenance when you encounter any
problems.
2. Install the camera away from TV, radio transmitter, magnet, electric
motor, transformer, audio speakers because the magnetic fields
generated from above devices will distort the video image.
3. Place this camera on a solid base. Install the camera away from
stoves or other heat generating devices as the high temperature could
cause deformation, discoloration or other damages to the camera.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK), NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is interned to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
①

Install the camera at where the temperature range does not exceed
-10°C to 50°C (14°F to 122°F)
4. Do not expose and operate the camera in the rain and humid areas.
5. Use only soft dry cloth to clean the camera. Also use lens tissue or
cotton tipped applicator and ethanol to clean the CCD sensor and
camera lens.
6. When the camera is not in use, put the cover cap on the lens mount.
Please do not touch the surface of CCD by bare hand.
Introduction
This OSD series CCD camera introduces a new level of high picture quality
through the digital signal processing LSI’s technology for advanced video
surveillance. It provides the most reliable and accurate color picture in the
security industry.
Main Features
zColor camera with high resolution SONY 1/3” EXview HAD II CCD
image sensor.
zEmploys SONY Enhanced Effio-E DSP chip-set for image control.
zControlled by OSD (On Screen Display) menu in 7 languages.
zHorizontal resolution of over 650TVL.
zATR (Adaptive Tone Reproduction).
z2D-NR (2D Noise Reduction).
zHLC (High Light Cover)
zSupports both C & CS mount lens.
②

Parts Names & Components
Hex Screwdriver
Auto Iris Plug
C-Mount Ring (Option)
Manual
Power LED Selection & setting buttons
Hole to fix lens
Auto iris connector
③

Auto Iris Function
DC DRIVE
Pin 1 (Red) Drive -
Pin 2 (N.C) Drive +
Pin 3 (White) Damp +
Pin 4 (Black) Damp -
④
Plug in auto iris connector
Screw the auto iris
lens on CS mount

Installation Instructions
(1) Remove the cap from the lens mount.
(2) Select the C mount lens (with mount ring) or CS mount lens.
(3) Screw and fasten the lens into the lens mount.
(4) Connect the video output wire between monitor and camera through
75ohm type coaxial cable.
(5) Connect the power cord input.
(6) When monitor shows the picture, please adjust the focus and iris of the
lens to obtain the best image according to the following procedures:
‧ Choose objects at a distance about 5 ~ 10 meter away.
‧ Loosen the mount lens fixing screw (use hex screwdriver), if
necessary.
‧ Turn the lens and the mount together until image is clear.
‧ Screw the mount to camera.
(7) Fix camera to the bracket, if necessary.
⑤

Switch Definition
SET button
Press to display the menu. In the menu, this button functions as “ENTER”.
UP & DOWN buttons
Press to select the item of menu.
LEFT & RIGHT buttons
Press to change the item value.
Size Dimension
DOWN button
LEFT SET RIGHT
button button button
UP button
⑥
Unit: mm

Menu Operation
‧ Press the SET button to display the menu on screen.
‧ Press the UP or DOWN button to select the item.
‧ The selected item will be displayed in gray text.
‧ Press the LEFT or RIGHT button to change mode.
‧ The ENTER symbol means there is a sub-menu. Press the SET
button to enter to the sub-menu.
‧ Select the SAVE ALL item and press the SET button to save settings.
‧ Select the EXIT item and press the SET button to exit the menu.
Advanced Functions
High Color Reproduction
¾Excellent color reproduction.
¾Wide range ATW (1,800°K~10,500°K)
⑦
Color chart (Machbeth)
Under halogen lamp
Still-life object
Under artificial sunlight
Conventional Over 650TVL Series
SETUP MENU
LENS MANUAL
SHUTTER/AGC AUTO
WHITE BAL ATW
BACKLIGHT OFF
PICT ADJUST
ATR OFF
NEXT
EXIT SAVE ALL
SETUP MENU
PRIVACY OFF
DAY/NIGHT AUTO
NR
CAMERA ID OFF
LANGUAGE ENGLISH
CAMERA RESET
BACK
EXIT SAVE ALL

High Resolution
¾Higher horizontal resolution of over 650TVL by SONY 1/3” EXview HAD
II CCD image sensor.
Over 650TVL Series
Truecapturedimage Resolution test chart
¾Finer image after E-Zoom operation
Over 650TVL Series
Original image
Conventional
⑧

Noise Reduction
ATR (Adaptive Tone Reproduction)
⑨
¾Noise reduction keeping image sharpness
NR OFF Conventional NR 2D-NR
Preserved edge
¾Excellent NR performance under low light condition
NROFF 2D-NR
¾Gradation compensation to improve image contrast.
¾Improvement of loss of dark detail and overexposure area.
Conventional Over 650TVL Series
ATROFF ATRON
Overexposure area improvement
Darkareaimprovement