Sony EVI-400 User manual

EVI-400/401
EVI-400DR/401DR
COLOR BLOCK CAMERA
Component/OEM
The EVI-400 and EVI-401 are color block
cameras that combine a 1/3 type CCD with
Super HAD technology (380k/440k pixels)
with a 12x optical zoom.
Equipped with functions not found in previous
models, these cameras also feature a
compact design for easy installation.
Incorporating Super HAD CCD technology,
these cameras achieve high sensitivity
(minimum object illumination of 1 lx). An
EEPROM chip contains the pre-programmed
factory default camera settings so the camera
setting can be stored without battery backup.
In addition to the standard RS-232C, these
cameras feature aTTL level interface to enable
a non-computer device to control camera
settings. The EVI-400DR and EVI-401DR
provide additional features such as a digital
zoom with a standard 2x zoom (max. 8x)
and a V-Lock function which allows the
camera to be controlled externally, thus
extending the potential range of applications
for these cameras.
1/3 type CCD with Super HAD technology
(380k/440k pixels)
High Sensitivity (1 lx at 50 IRE, High
Gain Mode)
Compact Size (47 mm x 55.4 mm x 82.5 mm)
12x Optical Zoom
2x
(max. 8x)Digital Zoom(EVI-400DR/401DR)
External Synchronization, V - Lock
(EVI-400DR /401DR)
5 Position Presets + Factory Default Preset
(EEPROM)
VISCA
TM
/RS-232C Control
TTL Level Interface
VISCA is an acronym of Video System Control Architecture.
It is a network protocol designed to interface a wide variety of
equipment to computer.
Outline Features
TM
TM

Camera functions can be controlled remotely
Camera Control
VISCA
TM
/ RS-232C or
direct inteface
EVI-400/
401
EVI-400DR/
401DR
Control
circuit board
Display
only
Power ON / OFF
Zoom Standard Tele / Wide
Zoom Fast Tele / Wide
Zoom Position (Preset / Detect)
Digital Zoom ON / OFF
Focus Auto / Manual
Focus Far / Near
Focus Position (Preset / Detect)
AF mode Selection
Interval AF Time
AF Sensitivity Low / Normal
White Balance mode Selection
One PushWhite Balance (Preset)
White Balance mode(Detect)
ATW Condition Normal/ Indoor/ Outdoor
AE Sensitivity High / Normal
Spot AE
Bright Control Up / Down
Exposure Compensation Up / Down
Shutter Priority Up / Down
Shutter Priority
(Preset)
Shutter Priority (Detect)
Iris Priority Up / Down
Iris Priority
(Preset)
Iris Priority (Detect)
Manual Shutter Up / Down
Manual Shutter
(Preset)
Manual Shutter (Detect)
Manual Iris Up / Down
Manual Iris
(Preset)
Manual Iris (Detect)
Manual Gain Up / Down
Manual Gain
(Preset)
Manual Gain (Detect)
Position Preset (Preset / Reset)
Position Preset (Detect)
Date and time (Set / Display)
Character (Set / Display)
Camera ID (Set / Display)
User Support (Preset / Reset)
V-Phase Adjustment
●
Direct Interface
Transmission signal levels for VISCA interface can be set to
0 0.3V (low)and 4.5 5.0V(high).
●
Control Circuit Board
Depending on the type of "add-on" control circuit board,
the functions listed above are controllable. An MD-78
CN104 (27P) connector is used for connection with a 27-
pin flat cable. For details of the circuit design and
specifications, refer to the instruction manual.
■Autofocus
Interval AF
The autofocusing mechanism is activated repeatedly at
regular intervals, but the interval (latency) can be set.
Zoom Trigger AF
The autofocusing mechanism is activated when zooming
begins; after a given period of time autofocusing stops.
The duration of autofocusing can be set.
OnePush AF
After sending a trigger command through the VISCA inter-
face, the autofocus function works only for the time period set.
AF Sensitivity
The autofocus function can be set to a lower sensitivity.
To adjust for changes in the illumination conditions, repeti-
tious autofocusing can be controlled.
■ AE Gain
A maximum gain value can be selected. High Gain Mode
offers a maximum 10 dB increase in sensitivity.A minimum
object illuminance of 1 lx is achievable in High Gain mode.
■ Position Preset
Five preset camera settings can be stored semi-
permanently in EEPROM (electrically erasable and
programmable ROM).
■ Factory Preset
The factory default settings can be changed by custom
settings without using the position preset function. Custom
settings available include: (1) digital zoom magni-
fication; (2) zoom speed; (3) zoom limiter settings (tele-
scopic/wide); and (4) close focusing limiter settings.
Details are available upon request.
■ User Support (EEPROM set)
The EEPROM (electrically erasable and programm-
able ROM) has address space in which users can
store user defined settings. Date of manufacture, ID,
and other data are also recorded and can be retrieved.
■ External Synchronization
(V-Lock Synchronization)
V-Phase can be synchronized externally by inputting a
V-Lock signal via a CN700 connector to the MD-78
circuit board. (EVI-400DR/401DR)
Note:
V-Lock synchronization is a simplified synchronization method,
so unlike VBS Gen-lock, color signals cannot be synchronized.

1 GND
2 C OUT
3 GND
4 Y OUT
5 GND
6 VBS OUT
1 VL PULSE IN
2 FREQ PULSE IN
3 GND
1 TXD IN_RS
2 DTR IN_RS
3 DSR IN_RS
4 RXD IN_RS
5 TXD IN_DIRECT
6 DTR IN_DIRECT
7 DSR IN_DIRECT
8 RXD IN_DIRECT
9 GND
10 AF LED
1 ZOOM WIDE
2 ZOOM TELE
3 AF ON / OFF
4 FOCUS NEAR
5 FOCUS FAR
6 GND
7 AF LED
8 USER PORT IN 1
9 USER PORT IN 2
10 USER PORT OUT 1
11 USER PORT OUT 2
1 DC IN (6 12V)
2 GND
10 AF LED
10 USER PORT OUT 1
11 USER PORT OUT 2
■Connector Location
■Pin Assignments
CN301 (Power)
CN001 CN206 CN101
CN104
CN700 CN204
CN301
CN001 (Video Out)
CN700 (External Sync.)
CN204 (VISCATM / Direct)CN206
(Zoom, Focus Control /
User Port in /Out)
CN104 (External Control)
Refer to the instruction manual.
Accessory cables
The EVI-400/401 is shipped with 5 cables, and the EVI-400DR / 401DR is shipped with 6 cables in the unit packaging box.
●
Connector Harness(Supplied Accessory)
2P,3P(White),6P,10P,11P,
3P(Red without EVI-401)
●
WideConversion Lens(Optional)
•
VCL-0637W
•
0.6x Wide Conversion
●
Filter Attachment Adaptor
(Optional Accessory)
• LO-400F
●
37mm Adaptor Lens
(Optional)
Conversion lenses for Sony
Camcorders having 37mm screw
can be used with the EVI-400/401/
400DR/401DR
Accessory
The RS-232 Control Protocol and Command List is provided by Sony on an "AS-IS BASIS" without warranty of any kind. Sony does not warrant any
particular result from the use of this Control Protocol and Command List and disclaims and excludes all warranties, express or implied, with respect to
that Control Protocol and Command List, including, but not limited to, any or all implied warranties of merchantability or fitness for a particular purpose. In
fact, Sony specifically acknowledges that software developed based on this Control Protocol and Command List may cause malfunction or damage to
hardware and software used with it (including Sony hardware and software) and specifically disclaims any liability for any such malfunction or damage.
This Control Protocol and Command List should be used with caution.
To control the camera via RS-232C, see the RS-232C Command List and the demonstration software.

(Unit:mm)
1-800-686-SONY
Specifications
Dimensions
Sony Electronics Inc.
Broadcast and Professional Company
1 Sony Drive
Park Ridge, NJ 07656
www.sony.com/videocameras
IS-1099-A
Printed in U.S.A. (6/01)
© 2001 Sony Corporation. All rights reserved.
Reproduction in whole or in part without written permission is prohibited.
Features and specifications are subject to change without notice.
All non-metric weights and measures are approximate.
Sony, Super HAD and VISCA are trademarks of Sony.
EVI-400 (NTSC)EVI-401 (PAL)
752 (H) 582 (V)
EVI-400DR (NTSC)
768 (H)494 (V)
EVI-401DR (PAL)
752 (H) 582 (V)
Y: 1.0 V p-p sync negative
C: 0.286 V p-p
VBS: 1.0 V p-p composite
Y: 1.0 V p-p sync negative
C: 0.3 V p-p
VBS: 1.0 V p-p composite
Y: 1.0 V p-p sync negative
C: 0.3 V p-p
VBS: 1.0 V p-p composite
more than 460TV lines
more than 350TV lines more than 450TV lines
more than 400TV lines more than 460TV lines
more than 350TV lines more than 450TV lines
more than 400TV lines
27 steps
(1/60 to 1/10,000 s) 28 steps
(1/50 to 1/10,000 s) 27 steps
(1/60 to 1/10,000 s) 28 steps (1/50 to 1/10,000 s)
1/3 type Super HAD CCD
12x zoom, f = 5.4 to 64.8, F = 1.8 to 2.7, Wide Macro, Autofocus (Inner Focus System)
9 elements in 6 groups (incl. 2 aspherical lenses)
10 mm (wide end), 800 mm (tele end)
1 lx (typical value) F 1.8 (at 50 IRE)
more than 48dB
ATW, One push WB, Indoor Preset, Outdoor Preset
Auto Focus, Manual Focus, One push trigger AF, Zoom trigger AF, Interval AF
2P and 3P (White), 3P (Red, excl. EVI-401), 6P, 10P, and 11P Harnesses
0 to 50 C -20 to 60 C
30 to 85% 20 to 90%
Internal Internal / External
6 to12 Vdc. 2.4W (inactive motor) /3.2W (active motor) 6 to12 Vdc. 2.6W (inactive motor) / 3.5W (active motor)
175g 176g
2x (total x 24 with optical zoom)
8x max. (total 96x with optical zoom)
approx. 48.8˚ (wide end) to approx. 4.4˚ (tele end)
approx. 37.6˚ (wide end) to approx. 3.3˚ (tele end)
TM
Image Sensor
Effective Picture Elements
Horizontal Resolution (center)
Vertical Resolution (center)
Lens
Digital Zoom
Angle of view (H)
(V)
Lens Construction
Min. Working Distance
Video Out
(75 Terminated)
Sync. System
External Sync.
(V-Lock)
Minimum Illumination
S/N Ratio
White Balance
Focus
Electronic Shutter
Operating temp./humidity
Operating temp./humidity
Power Requirements
Dimensions(W/H/D)
Weight
Supplied Accessories
47 55.4 82.5mm
High: 3.0 to 5.5 V Impendance: 94K (typical value)
Low: less than 0.3 V Frequency deviation: 1%
768 (H)494 (V)
Y: 1.0 V p-p sync negative
C: 0.286 V p-p
VBS: 1.0 V p-p composite