Sony STR-DB930 - Fm Stereo/fm-am Receiver User manual

S
O
N
Y.
3-866-968-11(1)
FM Stereo
FM-AM Receiver
Operating Instructions
STR-DB930
STR-DB830
€ 1999 by Sony Corporation

WARNING
To prevent fire or shock
hazard,
do
not
expose
the
unit to rain or moisture.
SACTUN NOEL тч RISA OF ELECTRIC SHOR
осот прими COVER SOR RACY
MOUSER SERVE ABEL PARTS INSIDE
жокка SERVIRA TO OAL IED SERA E PORSCHE
This symbol is intended to alert the user to
the presence of uninsulated “dangerous
voltage” within the product's enclosure
that may be of sufficient magnitude to
constitute a risk of electric shock to
persons.
A
This symbol is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
INFORMATION
This equipment has been tested and found
to comply with the limits for a Class B
digital device, pursuant to Part 15 of the
FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment off and on, the user
is encouraged to try to correct the
interference by one or more of the
following measures:
~ Reorient or relocate the receiving
antenna.
~ Increase the separation between the
equipment and receiver.
= Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced
radio/TV technician for help.
2
CAUTION
You are cautioned that any changes or
modification not expressly approved in
this manual could void your authority to
operate this equipment.
Note to CATV system installer:
This
reminder
is
provided
to
call
CATV
System
installer's
attention
to
Article
820-
30
of
the
NEC
that
provides
guidelines
for
proper
grounding
and,
in
particular,
specifies
that
the
cable
ground
shall
be
connected
to
the
grounding
system
of
the
building,
as
close
to
the
point
of
cable
entry
as
practical.
Owner's Record
The model and serial numbers are located
on the rear of the unit. Record the serial
number in the space provided below.
Refer to them whenever you call upon
your Sony dealer regarding this product.
Model Мо. STR-DB930/DB830
Serial No.
For the customers in Canada
CAUTION
TO PREVENT ELECTRIC SHOCK, DO
NOT USE THIS POLARIZED AC PLUG
WITH AN EXTENSION CORD,
RECEPTACLE OR OTHER OUTLET
UNLESS THE BLADES CAN BE FULLY
INSERTED TO PREVENT BLADE
EXPOSURE.
Se у лан
Precautions
On safety
Should any solid object or liquid fall into
the cabinet, unplug the receiver and have it
checked by qualitied personnel before
operating it any further.
On power sources
• Before operating the receiver, check that
the operating voltage is identical with
your local power supply. The operating
voltage is indicated on the nameplate at
the rear of the receiver.
* The unit is not disconnected from the AC
power source (mains) as long as it is
connected to the wall outlet, even if the
unit itself has been turned off.
• If you are not going to use the receiver
for a long time, be sure to disconnect the
receiver from the wall outlet. To
disconnect the AC power cord, grasp the
plug itself; never pull the cord.
• One blade of the plug is wider than the
other for the purpose of safety and will
fit into the wall outlet only one way. If
you are unable to insert the plug fully
into the outlet, contact your dealer.
• AC power cord must be changed only at
the qualified service shop.
On placement
* Place the receiver іп a location with
adequate ventilation to prevent heat
buildup and prolong the life of the
receiver.
* Do not place the receiver near heat
sources, or in a place subject to direct
sunlight, excessive dust or mechanical
shock.
• Do not place anything on top of the
cabinet that might block the ventilation
holes and cause malfunctions.
On operation
Before connecting other components, be
sure to turn off and unplug the receiver.
On cleaning
Clean the cabinet, panel and controls with
a soft cloth slightly moistened with a mild
detergent solution. Do not use any type of
abrasive pad, scouring powder or solvent
such as alcohol or benzine.
If you have any question or problem
concerning your receiver, please
consult your nearest Sony dealer.

[__-__-_- ____-_________-_ ________--_-__-__-_ ==
About This Manual
The instructions in this manual are for models STR-DB930
and STR-DB830. Check your model number by looking at
the upper right corner of the front panel. In this manual,
the STR-DB930 is used for illustration purposes unless
stated otherwise. Any difference in operation is clearly
indicated in the text, for example, “STR-DB930 only."
Type of differences
Model DB930 DB830
Feature
5 audio/5 video inputs e
4 audio/5 video inputs e
Conventions
* The instructions in this manual describe the controls on
the receiver. You can also use the controls on the
supplied remote if they have the same or similar names
as those on the receiver. For details on the use of your
remote, refer to the separate operating instructions
supplied with the remote.
* The following icon is used in this manual:
VW Indicates hints and tips for making the task easier.
This receiver incorporates Dolby* Digital and Pro Logic
Surround and the DTS** Digital Surround System.
* Manufactured under license from Dolby Laboratories.
"Dolby", "AC-3", "Pro Logic" and the double-D symbol OQ are
trademarks of Dolby Laboratories.
*xManufactured under license from Digital Theater Systems, Inc. US
Pat. No. 5,451,942 and other worldwide patents issued and pending.
"DTS" and “DTS Digital Surround" are trademarks of Digital
Theater Systems, Inc. © 1996 Digital Theater Systems, Inc. All
rights reserved.
Demonstration Mode
The demonstration will activate the first time you turn on
the power. When the demonstration starts, the following
message appears in the display twice:
"Now Demonstration Mode!! If you finish
demonstration, please press POWER KEY while
this message appears in the display. Thank you!”
To cancel the demonstration
Press 1/0) to turn the receiver off during the previous
message. The next time you turn the receiver on, the
demonstration will not appear.
To view the demonstration
Hold down SET UP and press 1/() to turn on the power.
Note
Running the demonstration will clear the receiver's
memory. For details on what will be cleared, see "Clearing
the receiver's memory" on page 18.
TABLE OF CONTENTS
Hooking Up the Components 4
Unpacking 4
Antenna Hookups 5
Audio Component Hookups 6
Video Component Hookups 8
Digital Component Hookups 9
5.1CH Input Hookups 11
Other Hookups 12
Hooking Up and Setting Up the
Speaker System 15
Speaker System Hookup 16
Performing Initial Setup Operations 18
Multi Channel Surround Setup 19
Before You Use Your Receiver 23
Location of Parts and Basic
Operations 26
Front Panel Parts Description 26
Enjoying Surround Sound 31
Selecting a Sound Field 32
Understanding the Multi-Channel Surround
Displays 36
Customizing Sound Fields 38
Receiving Broadcasts 43
Direct Tuning 44
Automatic Tuning 45.
Preset Tuning 45
Other Operations 47
Naming Preset Stations and Program Sources 48
Recording 48
Using the Sleep Timer 49
Adjustments Using the SET UP Button 50
Additional information 51
Troubleshooting 51
Specifications 53
Glossary 55
Tables of Settings Using SUR, LEVEL, EQ, and
SET UP buttons 56
Index 58

Hooking Up
the
Components
This chapter describes how to connect
various audio and video components
to the receiver. Be sure to read the
sections for the components you have
before you actually connect them to
the receiver.
Unpacking
Check that you received the following items with the unit:
• FM wire antenna (1)
• AM loop antenna (1)
e Audio/video/ control 5 connecting cord (1)
• CONTROL Al connecting cord (1)
• FM antenna adapter (1)
STR-DB930 only
¢ Remote commander RM-LJ302 (remote) (1)
• LR6 (size-AA) alkaline batteries (3)
STR-DB830 only
• Remote commander RM-PP402 (remote) (1)
e R6 (size-AA) batteries (2)
Inserting batteries into the remote
Insert the LR6 (STR-DB930) or R6 (STR-DB830) (size-AA)
batteries with the + and – properly oriented in the battery
compartment. When using the remote, point it at the
remote sensor Bl on the receiver.
For details, refer to the operating instructions supplied
with your remote.
€" When to replace batteries
Under normal conditions, the batteries should last for about 3
months (STR-DB930 only) or 6 months (STR-DB830 only). When
the remote no longer operates the receiver, replace all batteries
with new ones.
Notes
* Do not leave the remote in an extremely hot or humid place.
* Do not use a new battery with an old one.
* Do not expose the remote sensor to direct sunlight or lighting
apparatuses. Doing so may cause a malfunction.
* [f you don't use the remote for an extended period of time,
remove the batteries to avoid possible damage from battery
leakage and corrosion.
* This remote is designed for use with alkaline batteries only. Do
not use a combination of different battery types (STR-DB930
only).
Before you get started
* Turn off the power to all components before making
any connections.
* Do not connect the AC power cords until all of the
connections are completed.
* Be sure to make connections firmly to avoid hum and
noise.
* When connecting an audio/ video cord, be sure to
match the color-coded pins to the appropriate jacks on
the components: yellow (video) to yellow; white (left,
audio) to white; and red (right, audio) to red.

Antenna Hookups
AM loop antenna
(supplied)
FM wire antenna
(supplied)
Terminals for connecting the antennas
Connect the To the
AM loop antenna AM terminals
FM wire antenna ЕМ 750 COAXIAL terminal
Assembling the supplied FM antenna
The supplied FM wire antenna must be connected to the
supplied FM antenna adaptor.
1 Strip insulation off one end of the wire antenna.
5-7 mm
=
2 Open the antenna adaptor.
Pull up on the tab and pull the back away.
1
3 insert wire antenna into adaptor and wedge
stripped end between the forks.
4 Close the adaptor.
5 Attach the adaptor to the FM antenna terminal.
Notes on antenna hookups
* To prevent noise pickup, keep the AM loop antenna
away from the receiver and other components.
* Be sure to fully extend the FM wire antenna.
* After connecting the FM wire antenna, keep it as
horizontal as possible.
var you have poor FM reception
Use a 75-ohm coaxial cable (not supplied) to connect the receiver
to an outdoor FM antenna as shown below.
Receiver
- Outdoor FM antenna
Ground wire
(not supplied)
To ground
Important
If you connect the receiver to an outdoor antenna, ground
it against lightning. To prevent a gas explosion, do not
connect the ground wire to a gas pipe.
Note
Do not use the h SIGNAL GND terminal for grounding the
receiver.
"
зизиодшој eui ап Buryoon |

Audio Component Hookups
STR-DB930
MD/DAT deck
Turntable
Required cords
Audio cords (not supplied)
When connecting a cord, be sure to match the color-coded pins to
the appropriate jacks on the components.
White (L) White (L)
Red (R) 5 ред (R)
SPEAKERS IMPEDANCE USE 3 Tf
CD player
Tape deck
Jacks for connecting audio components
Connect a To the
Turntable PHONO jacks
CD player CD jacks
Tape deck TAPE jacks
MD deck or DAT deck MD/DAT jacks
Note on audio component hookups
If your turntable has a ground wire, connect it to the
+ SIGNAL GND terminal on the receiver.

STR-DB830
Required cords
Audio cords (not supplied)
When connecting a cord, be sure to match the color-coded pins to
MD/Tape deck
INPU* OUTPUT
the appropriate jacks on the components.
White (L) White (L)
Red (R) i P Red (R)
Turntab
TAPE МСТАРЕ TVSAT OVOLO OVOLO
Perca. ОотСл. ОРТСА, OPTICAL COAX!
OS D b * ч
28
SPEAKERS.
IMPEDANCE USE 2.16
CD player
Jacks for connecting audio components
Connect a To the
Turntable PHONO jacks
CD player CD jacks
MD deck or Tape deck MD/TAPE jacks
Note on audio component hookups
If your turntable has a ground wire, connect it to the
+ SIGNAL GND terminal on the receiver.
sjueuoduio» au) dn бигјоон
еб

Video Component Hookups
TV or satellite tuner OVD or LD player
OUTPUT
OUTPUT
Required cords
Audio/video cords (not supplied)
When connecting a cord, be sure to match the color-coded pins to
the appropriate jacks on the components.
_ Yellow (video)
White (L/audio)
Red (R/audio)
Red (R/audio)
Video cord for connecting a TV monitor (not supplied)
You can use the video cord of the supplied audio/video/control
S cord (see pages 12 and 13 for details).
Yellow
Yeliow
B
©
©
To the front panel
|
OUT
IN
L
INPUT [OUTPUT
Camcorder g
or video са
дате
TV monitor
SPEAKERS
IMPEDANCE USE 4.16."
{
=
INPUT OUTPUT
|
ойт
Jacks for connecting video components
Connect a To the
TV or satellite tuner TV/SAT jacks
VCR VIDEO 1 jacks
Additional VCR VIDEO 2 jacks
DVD or LD player DVD/LD jacks
TV monitor MONITOR VIDEO OUT jack
Camcorder or video game VIDEO 3 INPUT jacks on the
front panel
Note on video component hookups
You can connect your TV's audio output jacks to the TV /
SAT AUDIO IN jacks on the receiver and apply sound
effects to the audio from the TV. In this case, do not
connect the TV's video output jack to the TV/SAT VIDEO
IN jack on the receiver. If you are connecting a separate
TV tuner (or satellite tuner), connect both the audio and
video output jacks to the receiver as shown above.
€" When using the S-video jacks instead of the video jacks
Your monitor must also be connected via an S-video jack. S-video
signals are on a separate bus from the video signals and will not
be output through the video jacks.

Digital Component Hookups
Connect the digital output jacks of your DVD player and Required cords
satellite tuner (etc.) to the receiver's digital input jacks to D А
Optical digital cords (not supplied)
Black Black
Coaxial digital cord (not supplied)
speakers, two rear speakers, and a center speaker) and a
sub woofer are required. You can also connect an LD Yellow sC ID= Yellow
player with an RF OUT jack via an RF demodulator, like Audio/video cords (not supplied)
the Sony МОР-КЕ1 (not supplied).
bring the multi channel surround sound of a movie
theater into your home. To enjoy full effect of multi
channel surround sound, five speakers (two front
When connecting a cord, be sure to match the color-coded pins to
the appropriate jacks on the components.
Yellow (video) Yellow (video)
TV or satellite tuner DVD player (etc.)* White (L/audio)-Ci
L
White (L/audio)
Red (R/audio) i Red (R/audio)
DIGITAL
DIGITAL DIGITA
КИТА: COAXIAL
OPTICAL OPTICAL
AC OUTLET
QC
VIDEO 2
* Make either coaxial or optical connections. We recommended making coaxial connections instead of optical connections.
Example of LD player connected via an RF demodulator
Please note that you cannot connect an LD player's AC-3 RF OUT jack directly to this unit's digital input jacks. You must
first convert the RF signal to either an optical or coaxial digital signal. Connect the LD player to the RF demodulator, then
connect the RF demodulator’s optical or coaxial digital output to this unit’s OPTICAL or COAXIAL DVD/LD IN jack.
Refer to the instruction manual supplied with your RF Demodulator for details on AC-3 RF hookups.
DVD/LD
VIDEO
VIDEO OUT DIGITAL IN
DVD/LD IN | — m
LD player RF demodulator п АРЕ: О
x ==
оособово 5
«=== o
96%9000о „Юр: О
oo
oo ooo
Note
When making connections as shown above, be sure to set INPUT MODE ([3] on page 27) manually. This unit may not operate correctly if
INPUT MODE is set to "AUTO."
syuauoduio» əy} ап биҳоон |
on

(--____"--_--“_________--_-_-__-___________„ > ____- ______________ „о“ _ __.__-____________ 1, ee о]
Digital Component Hookups
Connect the digital output jacks of your MD or DAT deck Required cords
to the receiver's digital input jack and connect the digital
input jacks of your MD or DAT deck to the receiver's Optical digital cords (not supplied)
digital
output
jack.
These
connections
allow
you
to
make
Black
Black
digital
recordings
of
a
CDs
played
back
through
vour
DVD (ог LD player) and satellite broadcasts. Audio cords (not supplied)
When connecting a cord, be sure to match the color-coded pins to
the appropriate jacks on the components.
MD or DAT deck
DIGITAL White (0) White (L)
INPUT OUTPUT!
Red (r) —— — j Red (R)
e
© H
@ i
VIOEO 2 VIDEO 1 1240 AUDIO OUT
Notes
• Please note that you cannot make a digital recording of a digital multi channel surround signal.
* To make a digital recording from your CD player, connect-the CD player's digital output directly to the digital input on your MD or DAT
deck. Refer to the instructions supplied with your CD player and MD or DAT deck for details.
* The DVD/LD OPTICAL and COAXIAL jacks are compatible with 32 KHz, 44.1 KHz, 48 kHz and 96 kHz sampling frequencies.
* The TV/SAT OPTICAL IN jack and MD/DAT OPTICAL IN and OUT jacks are compatible with 32 kHz, 44.1 kHz, and 48 kHz sampling
frequencies.
* It is not possible to record analog signals to TAPE and VIDEO with only digital connections. To record analog signals, make analog
connections. To record digital signals, make digital connections.
* Input signals with 96 kHz sampling frequencies to the DVD/LD OPTICAL or COAXIAL jacks. Using other jacks may result in
intermittent sound.
10