Sony SA-WG99 User manual

SERVICE MANUAL
Sony Corporation
Home Audio Division
Published by SonyTechno Create Corporation
US Model
Canadian Model
ACTIVE SUBWOOFER
9-887-535-01
2007A16-1
© 2007.01
Ver. 1.0 2007.01
SPECIFICATIONS
SA-WG99
•SA-WG99 is the sub woofer section
in MHC-GX99.
Speaker system: bass-reflex type
Speaker units
Woofer: 20cm, cone type
Nominal impedance: 6 Ω
Dimensions (w/h/d): Approx. 280 ×306 ×405 mm
Mass: Approx. 8.7 kg
US model: 115 W
Canadian model: 155 VA
Design and specifications are subject to change without notice.
Power consumption:
Power requirement:
North American model: AC 120 V, 60 Hz
All manuals and user guides at all-guides.com
all-guides.com

2
SA-WG99
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety check before releasing the set to the customer:
Check the antenna terminals, metaltrim, “metallized” knobs, screws,
and all other exposed metal parts forAC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes.).
Leakage current can be measured by any one of three methods.
1. Acommercial leakagetester,such asthe Simpson 229 or RCA
WT-540A. Follow the manufacturers’instructions to use these
instruments.
2. A battery-operatedAC milliammeter.The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOMor battery-operatedACvoltmeter.The“limit” indication
is 0.75V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2V AC range are suitable. (See
Fig. A)
Fig. A. Using an AC voltmeter to check AC leakage.
1.5 k Ω 0.15 µ FAC
voltmete
r
(0.75 V)
To Exposed Metal
Parts on Set
Earth Ground
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0OR DOTTED LINE
WITH MARK 0ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0SUR
LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES
PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE
FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS
QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT
DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS
PUBLIÉS PAR SONY.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
•Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
•Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
•Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
All manuals and user guides at all-guides.com

3
SA-WG99
SECTION 1
DIAGRAMS
Note on PrintedWiring Boards:
•X: Parts extracted from the component side.
• a: Through hole.
• : Pattern from the side which enables seeing.
Note on Schematic Diagrams:
•All capacitors are in µF unless otherwise noted. (p: pF) 50
WV or less are not indicated except for electrolytics and
tantalums.
•2: nonflammable resistor.
•5: fusible resistor.
•All resistors are in Ωand 1/4W or less unless otherwise
specified.
•C: panel designation.
•A: B+ Line.
•B: B– Line.
•Voltages and dc with respect to ground under no-signal
conditions.
no mark : Power on
•Voltages are taken with aVOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production
tolerances.
•Signal path.
d: AUDIO
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.)
• Circuit Boards Location
Note:
The components identi-
fied by mark 0or dot-
ted line with mark 0are
critical for safety.
Replace only with part
number specified.
Note:
Les composants identifiés
par une marque 0sont cri-
tiques pour la sécurité.
Neles remplacer quepar une
piéce portant le numéro
spécifié.
POWER board
MAIN board
VOL-LED board
POWER SWITCH board
INPUT board
All manuals and user guides at all-guides.com

4
SA-WG99
•IC Block Diagram
– MAIN Board –
IC400 STK404-130S
1 2
SUB
345 6 7 8 9 10 11 12 13
Pre DRIVER
Power STAGE
+
–
Bias
PT-1 PT-2
SW IN
SW IN NF
SUB
-PRE
+PRE (12V)
-VCC
+VCC
-RE
+RE
All manuals and user guides at all-guides.com

55
SA-WG99
SA-WG99
1-1. PRINTED WIRING BOARDS — MAIN SECTION — • :Uses unleaded solder. •See page 3 for Circuit Boards Location.
• Semiconductor
Location
Ref. No. Location
D300 E-2
D400 G-9
D502 F-9
D504 F-6
D505 D-10
D506 D-7
D507 C-10
D508 F-10
D509 C-10
D600 B-9
D601 C-9
D602 D-7
D603 D-7
D605 E-7
D606 B-7
D607 B-6
D608 B-6
D609 B-6
IC400 G-8
Q200 C-5
Q201 D-6
Q202 D-6
Q400 G-9
Q503 G-7
Q504 G-6
Q505 G-6
Q506 G-6
Q507 F-6
Q508 E-5
Q509 F-10
Q510 E-10
Q511 G-10
Q600 D-6
IC400 1-872-047-
12
(12)
D509
D508
D505
D605
D504
D506
D507
D400
D502
Q504
Q200
E
E
Q507
Q510
E
Q201
Q508
Q511
E
E
Q503
Q505
Q400
Q202
Q506
R400
R401
R402
R210
R404
R211
R405
R212
R406
R213
R407
R214
R408
R409
R602R603
R605
R411
R606
R412
R607
R413
R414
R416
R417
R418
R419
R420
R421
R504
R505
R535
R506
R507
R534
R508
R509
R510
R511 R512
R514
R515
R516
R517
EE
E
E
E
E
E
E
R518
R519
R520
R521
R525
R526
R527
R528
R529
R531
R532
R533
R200
R201
R202
R203
R204
R205
R206
R207
R208
R209
C400
C407
C408
A001
JW207
JW208
R522
R523
R524
JW217
JW212
C607
CN500
JW219
C509
CN501
1
3
C510
JW201
JW206
C508
C507
JW203
JW216
JW218 JW214
113
JW210
JW209
JW211
JW205
JW400
C506
CN200
RY500
C504
C505
C503
C502
R513
ET600
SPEAKER
FAN
JW213
JW401
JW204
JW202 C605
C410
C603
C602
C409
C406
C404
C403
C401
C207
C206
C205
C204 C203
C202
C200
CN600
CN201
R410
R403
D603
D609
(CHASSIS)
1
8
D608
D602
D606
D600
D607
D601
Q600
Q509
MAIN BOARD
D300
1-872-051-
CN300
1
5
RV300
R300
12
(12)
CN100
12
1-872-050-
12
(12)
J100
J100
INPUT BOARD
(CHASSIS)
C600
C601
VOL-LED BOARD
APOWER BOARD
CN702
(Page 7)
INPUT
SUBWOOFER
LEVEL
MIN MAX
SUBWOOFER
ON/OFF
2345678910111
A
B
C
D
E
F
G
H
All manuals and user guides at all-guides.com

66
SA-WG99
SA-WG99
1-2. SCHEMATIC DIAGRAM — MAIN SECTION — • See page 4 for IC Block Diagram.
IC400
IC B/D
A
POWER BOARD
CN702
(Page 8)
3.6 3.0
11.5
5.9
11.5
5.2 5.0
11.5
4.4
0.7
0
0
0
11.5 17.8
12.2
0
11.5
12.8
0
0016
15.8
15.7
0.7 -3.0 0
17.8
15.8
17.8
0.4
0
0
17.8
11.5 11.5 00-51 11.5 1.1 -51.8 51.6 00
No mark:Power on
1k
R201
100k
R202
2SC3052EF-T1-LEF
BUFFER
BUFFER BUFFER
Q200
0
R208
2SC3052EF-T1-LEF
Q201
10k
R210 10k R211
2SC3052EF-T1-LEF
Q202
1k
R400
50V
2.2
C401
0.22
R410
100V100
C404
UDZW-TE17-12B
D605
7654321 1312111098
STK404-130S
POWER AMP
IC400
PT-1 PT-2 SW IN SW IN NF SUB -PRE +PRE (12V) -VCC +VCC -RE +RE
2SA2026
Q400
Q400
100k
R200
R605
2.2k
RY500
R420
2.2k
R508
100k
R534
15k
R510
47k
R512
47k
R511
22k
R507
100
R506
47k
R509
10k
C502
10016V
R505
100k
R519
22k
R518
22k
R521
12k
R520
56k
1
2
WHT
2P
CN500
SP-OUT
SPEAKER
FAN
SP-GND
C407
2200p
50V
R413
10k
R418
10
Q506
2SC5625
Q507
Q507
2SC3052EF-
T1-LEF
Q505
Q505
2SC3052EF-T1-LEF
Q504
Q504,
RELAY OFF
2SC3052EF-T1-LEF
16V47
C403
C409
0.1
50V
C410
0.1
50V
C406
47 50V
R403
100 1/4W
2SA1235TP-1EF
Q503
TEMPERATURE
PROTECTION
50V10
C200
10
R416
10
R419 10
R417
C408
3p 50V
CJ
50V
2.2
C504
50V
0.22
C202
50V
0.22
C203
C602
3300 71V
C603
3300 71V
1N5402-F46
D601
1N5402-F46
D600
0.1
100V
C600
0.1
100V
C601
1N5402-F46
D603
1N5402-F46
D602
R513
1.8k 2W
56k
R401
56k
R414
Q600
2SC2603TP-EF
+12V REG
10
JW400
R515
10k
JW401
12.5
R411
220
R412
4.7k
10k
R421
0.022
C505
47k
R203
R602
47k
R603
47k
47k
R504
2SC3052EF-T1-LEF
POWER LED DRIVE-2
OVER DRIVE
PROTECTION
Q508
50V
1
C506
100k
R606
2SC3052EF-T1-LEF
Q510
Q510
2SC3052EF
-T1-LEF
Q511
Q511
1
2
3
3P
CN501
VDD+
GND
VDD+
10EDB40-TB3
D606
10EDB40-TB3
D607
10EDB40-TB3
D608
10EDB40-TB3
D609
C507
4.7
50V
C508
10
50V
C509
4.7 50V
0
R214
50V
0.22
C204
R525
10k
R526
4.7k
R531
470
R527
4.7k
R528
47k
C510
47
50V
R532
220k
R529
100k
R522
10
1/4W
R523
10
1/4W
R524
10
1/4W
C503
330 25V
1.5k
R204
1k
R209 1k
R212
3.3k
R205
1.2k
R402
E
ET600
35V
470
C607
UDZW-TE17-5.1B
D508
UDZW-TE17-5.1B
D509
R533
4.7
KTA1273-Y-AT
Q509
82k
R206
100k
R207
50V
0.047
C205
1
2
3
4
5
6
7
8
8P
CN600
AC-1
AC-1
GND
GND
AC-1
AC-1
AC-2
AC-2
1k
R607
A001
(CHASSIS)
(CHASSIS)
R514
22k
R517
82k
1
2
3
4
5
5P
CN201
VOL-IN
GND
VOL-OUT
POWER-LED
GND
R516
100
16V100
C206
R213
2.2k
50V
1
C207
C605
100 16V
50V470p
B
C400
MA111-TX
D400
MA111-TX
D502
D504
MA111-TX
D505
MA111-TX
D506
MA111-TX
D507
MA111-TX
1
2
2P
CN200
IN
IN-GND
R404
15k
15k
R405
R406
15k
R407
15k
R408
15k
R409
15k
R535
10k
MAIN BOARD
SLR-325MCT31
D300
20k
RV300
R300
1.5k
1
2
3
4
5
5P
CN300
VOL-IN
GND
VOL-OUT
POWER-LED
GND
VOL-LED BOARD
RELAY DRIVE
POWER LED
DRIVE-1 FUN SWITCH
FUN DRIVE
FUN PROTECTION
SUBWOOFER
LEVEL
MIN MAX
SUBWOOFER
ON/OFF
1
2
CN100
2P
IN
IN-GND
J100
INPUT BOARD
INPUT
All manuals and user guides at all-guides.com
all-guides.com

77
SA-WG99
SA-WG99
1-3. PRINTED WIRING BOARDS — POWER SECTION — • :Uses unleaded solder. •See page 3 for Circuit Boards Location.
A
MAIN BOARD
CN600
(Page 5)
POWER SWITCH BOARD
SUBWOOFER
ON/OFF
A002
AC IN
FH704 FH705
F702
POWER TRANSFORMER
T700
JW705
JW702
FH703
FH702
FH701 FH700
CN703
CN702
CN700
R700
F701
F700
POWER BOARD
1-872-048-
12
(12)
S700
1-872-049- (12)
C700
CN701
12
1
3
3
3
16
15
14
13
12
11
10
Not
replaceable
Built in transformer
9
*
*
8
5
6
7
1
23456781
A
B
C
D
E
F
G
H
I
All manuals and user guides at all-guides.com

88
SA-WG99
SA-WG99
1-4. SCHEMATIC DIAGRAM — POWER SECTION —
A
MAIN BOARD
CN600
(Page 6)
1
3
YEL
2P
CN700
PSW-1
PSW-2
7
13
14
10
12
11
15 3
5
8
9
16
4
6
T700
POWER TRANSFORMER
R700
1
3
WHT
AC IN
2P
CN703
LIVE
NEUTRAL
1
2
3
4
5
6
7
8
8P
CN702
AC-1
AC-1
GND
GND
AC-1
AC-1
AC-2
AC-2
FH705
Not replaceable
Built in
transformer
FH700
FH702
FH704
FH703
FH701
F700
F701
F702
JW702
POWER BOARD
S700
C700
250V
F
0.01
1
3
WHT
2P
CN701
PSW-1
PSW-2
POWER SWITCH BOARD
T6.3AL/ 250V
T6.3AL/ 250V
1
T4AL/250V
*
*
1/4W
SUBWOOFER
ON/OFF
All manuals and user guides at all-guides.com

9
SA-WG99
SECTION 2
EXPLODEDVIEWS
NOTE:
•-XX and -X mean standardized parts, so they
may have some difference from the original
one.
•Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when
ordering these items.
•The mechanical parts with no reference
numberin the exploded viewsarenot supplied. The components identified by mark 0or
dotted line with mark 0are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque 0
sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant le
numéro spécifié.
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1X-2176-957-1 FRONT PANEL ASSY
22-893-823-01 KNOB (VOL)
32-893-824-01 KNOB (SW)
44-874-614-02 SCREW (1) (3.5X14), TAPPING
51-787-344-11 FAN, DC
061-830-190-11 CORD, POWER
74-985-672-01 SCREW (+PTPWHM2.6), FLOATING
83-703-244-00 BUSHING (2104), CORD
9A-1219-064-A MAIN BOARD, COMPLETE
10 3-905-609-31 SCREW (TRANSISTOR)
0F700 1-532-325-00 FUSE, TIME-LAG 6.3AL/250V
0F701 1-532-325-00 FUSE, TIME-LAG 6.3AL/250V
0F702 1-532-504-00 FUSE, TIME-LAG 4AL/250V
SP1 1-826-588-11 LOUDSPEAKER (20cm)
0T700 1-445-114-11 TRANSFORMER, POWER
#1 7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S
#2 7-685-881-09 SCREW +BVTT 4X8 (S)
2-1. OVERALL SECTION
1
6
4
4
8
7
10
3
4
2
9
5
not
supplied not
supplied
not
supplied
not
supplied
not
supplied
not
supplied
not
supplied
not
supplied
not supplied
not
supplied
not
supplied
4
#1
#1
#1
#1
#1 #1
#1
#1
#2
#2
SP1
T700 F701
F702
F700
All manuals and user guides at all-guides.com

10
SA-WG99 SECTION 3
ELECTRICAL PARTS LIST
NOTE:
•Due to standardization, replacements in the
parts list may be different from the parts
specified in the diagrams or the components
used on the set.
•-XX and -X mean standardized parts, so they
may have some difference from the original
one.
•Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when
ordering these items.
•CAPACITORS
uF: µF
•COILS
uH: µH
•RESISTORS
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable
•SEMICONDUCTORS
In each case, u: µ, for example:
uA. . : µA. . uPA. . : µPA. .
uPB. . : µPB. . uPC. . : µPC. .
uPD. . : µPD. .
When indicating parts by reference number,
please include the board name.
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
INPUT BOARD
***********
< JACK >
J100 1-820-968-11 JACK, PIN 1P (INPUT)
*************************************************************
A-1219-064-A MAIN BOARD, COMPLETE
*********************
< CAPACITOR >
C200 1-126-964-11 ELECT 10uF 20% 50V
C202 1-137-190-91 FILM 0.22uF 5% 50V
C203 1-137-190-91 FILM 0.22uF 5% 50V
C204 1-137-190-91 FILM 0.22uF 5% 50V
C205 1-136-161-00 FILM 0.047uF 5% 50V
C206 1-126-933-11 ELECT 100uF 20% 16V
C207 1-126-960-11 ELECT 1uF 20% 50V
C400 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
C401 1-126-961-11 ELECT 2.2uF 20% 50V
C403 1-126-947-11 ELECT 47uF 20% 35V
C404 1-128-563-11 ELECT 100uF 20% 100V
C406 1-126-967-11 ELECT 47uF 20% 50V
C407 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C408 1-162-908-11 CERAMIC CHIP 3PF 0.25PF 50V
C409 1-136-497-81 FILM 0.1uF 5% 50V
C410 1-136-497-81 FILM 0.1uF 5% 50V
C502 1-126-933-11 ELECT 100uF 20% 16V
C503 1-126-940-11 ELECT 330uF 20% 25V
C504 1-126-961-11 ELECT 2.2uF 20% 50V
C505 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
C506 1-126-960-11 ELECT 1uF 20% 50V
C507 1-126-963-11 ELECT 4.7uF 20% 50V
C508 1-126-964-11 ELECT 10uF 20% 50V
C509 1-126-963-11 ELECT 4.7uF 20% 50V
C510 1-126-967-11 ELECT 47uF 20% 50V
C600 1-137-749-11 MYLAR 0.1uF 100V
C601 1-137-749-11 MYLAR 0.1uF 100V
C602 1-135-517-11 ELECT 3300uF 20% 71V
C603 1-135-517-11 ELECT 3300uF 20% 71V
C605 1-126-933-11 ELECT 100uF 20% 16V
C607 1-126-951-11 ELECT 470uF 20% 35V
< CONNECTOR >
CN200 1-815-443-11 PIN, CONNECTOR (PWB) 2P
CN201 1-819-133-11 PIN, CONNECTOR
CN500 1-564-320-00 PIN, CONNECTOR (3.96mm PITCH) 2P
CN501 1-819-131-11 PIN, CONNECTOR 3P
CN600 1-819-136-11 PIN, CONNECTOR 8P
< DIODE >
D400 8-719-404-50 DIODE MA111-TX
D502 8-719-404-50 DIODE MA111-TX
D504 8-719-404-50 DIODE MA111-TX
D505 8-719-404-50 DIODE MA111-TX
D506 8-719-404-50 DIODE MA111-TX
D507 8-719-404-50 DIODE MA111-TX
D508 6-501-167-01 DIODE UDZW-TE17-5.1B
D509 6-501-167-01 DIODE UDZW-TE17-5.1B
D600 6-501-046-01 DIODE 1N5402-F46
D601 6-501-046-01 DIODE 1N5402-F46
D602 6-501-046-01 DIODE 1N5402-F46
D603 6-501-046-01 DIODE 1N5402-F46
D605 6-501-176-01 DIODE UDZW-TE17-12B
D606 6-500-522-21 DIODE 10EDB40-TB3
D607 6-500-522-21 DIODE 10EDB40-TB3
D608 6-500-522-21 DIODE 10EDB40-TB3
D609 6-500-522-21 DIODE 10EDB40-TB3
< GROUND TERMINAL BOARD >
ET600 1-537-771-21 TERMINAL BOARD, GROUND
< IC >
IC400 6-600-091-01 IC STK404-130S
< TRANSISTOR >
Q200 8-729-120-28 TRANSISTOR 2SC1623-L5L6
Q201 8-729-120-28 TRANSISTOR 2SC1623-L5L6
Q202 8-729-120-28 TRANSISTOR 2SC1623-L5L6
Q400 6-551-270-01 TRANSISTOR 2SA2026
Q503 8-729-600-22 TRANSISTOR 2SA1235-F
Q504 8-729-120-28 TRANSISTOR 2SC1623-L5L6
Q505 8-729-120-28 TRANSISTOR 2SC1623-L5L6
Q506 6-551-268-01 TRANSISTOR 2SC5625
Q507 8-729-120-28 TRANSISTOR 2SC1623-L5L6
Q508 8-729-120-28 TRANSISTOR 2SC1623-L5L6
Q509 8-729-040-76 TRANSISTOR KTA1273-Y-AT
Q510 8-729-120-28 TRANSISTOR 2SC1623-L5L6
Q511 8-729-120-28 TRANSISTOR 2SC1623-L5L6
Q600 8-729-620-05 TRANSISTOR 2SC2603-EF
The components identified by mark 0or
dotted line with mark 0are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque 0
sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant le
numéro spécifié.
MAININPUT
All manuals and user guides at all-guides.com

11
SA-WG99
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
< RESISTOR >
R200 1-216-845-11 METAL CHIP 100K 5% 1/10W
R201 1-216-821-11 METAL CHIP 1K 5% 1/10W
R202 1-216-845-11 METAL CHIP 100K 5% 1/10W
R203 1-216-841-11 METAL CHIP 47K 5% 1/10W
R204 1-216-823-11 METAL CHIP 1.5K 5% 1/10W
R205 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
R206 1-216-844-11 METAL CHIP 82K 5% 1/10W
R207 1-216-845-11 METAL CHIP 100K 5% 1/10W
R208 1-216-864-11 SHORT CHIP 0
R209 1-216-821-11 METAL CHIP 1K 5% 1/10W
R210 1-216-833-11 METAL CHIP 10K 5% 1/10W
R211 1-216-833-11 METAL CHIP 10K 5% 1/10W
R212 1-216-821-11 METAL CHIP 1K 5% 1/10W
R213 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R214 1-216-864-11 SHORT CHIP 0
R400 1-216-821-11 METAL CHIP 1K 5% 1/10W
R401 1-216-842-11 METAL CHIP 56K 5% 1/10W
R402 1-216-822-11 METAL CHIP 1.2K 5% 1/10W
0R403 1-212-881-11 FUSIBLE 100 5% 1/4W
R404 1-216-835-11 METAL CHIP 15K 5% 1/10W
R405 1-216-835-11 METAL CHIP 15K 5% 1/10W
R406 1-216-835-11 METAL CHIP 15K 5% 1/10W
R407 1-216-835-11 METAL CHIP 15K 5% 1/10W
R408 1-216-835-11 METAL CHIP 15K 5% 1/10W
R409 1-216-835-11 METAL CHIP 15K 5% 1/10W
R410 1-234-182-11 ENCAPSULATED COMPONENT
R411 1-216-813-11 METAL CHIP 220 5% 1/10W
R412 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R413 1-216-833-11 METAL CHIP 10K 5% 1/10W
R414 1-216-842-11 METAL CHIP 56K 5% 1/10W
R416 1-216-797-11 METAL CHIP 10 5% 1/10W
R417 1-216-797-11 METAL CHIP 10 5% 1/10W
R418 1-216-797-11 METAL CHIP 10 5% 1/10W
R419 1-216-797-11 METAL CHIP 10 5% 1/10W
R420 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R421 1-216-833-11 METAL CHIP 10K 5% 1/10W
R504 1-216-841-11 METAL CHIP 47K 5% 1/10W
R505 1-216-845-11 METAL CHIP 100K 5% 1/10W
R506 1-216-841-11 METAL CHIP 47K 5% 1/10W
R507 1-216-809-11 METAL CHIP 100 5% 1/10W
R508 1-216-845-11 METAL CHIP 100K 5% 1/10W
R509 1-216-833-11 METAL CHIP 10K 5% 1/10W
R510 1-216-841-11 METAL CHIP 47K 5% 1/10W
R511 1-216-837-11 METAL CHIP 22K 5% 1/10W
R512 1-216-841-11 METAL CHIP 47K 5% 1/10W
0R513 1-216-458-11 METAL OXIDE 1.8K 5% 2W F
R514 1-216-837-11 METAL CHIP 22K 5% 1/10W
R515 1-216-833-11 METAL CHIP 10K 5% 1/10W
R516 1-216-809-11 METAL CHIP 100 5% 1/10W
R517 1-216-844-11 METAL CHIP 82K 5% 1/10W
R518 1-216-837-11 METAL CHIP 22K 5% 1/10W
R519 1-216-837-11 METAL CHIP 22K 5% 1/10W
R520 1-216-842-11 METAL CHIP 56K 5% 1/10W
R521 1-216-834-11 METAL CHIP 12K 5% 1/10W
R522 1-249-393-11 CARBON 10 5% 1/4W
R523 1-249-393-11 CARBON 10 5% 1/4W
R524 1-249-393-11 CARBON 10 5% 1/4W
R525 1-216-833-11 METAL CHIP 10K 5% 1/10W
R526 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R527 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R528 1-216-841-11 METAL CHIP 47K 5% 1/10W
R529 1-216-845-11 METAL CHIP 100K 5% 1/10W
R531 1-216-817-11 METAL CHIP 470 5% 1/10W
R532 1-216-849-11 METAL CHIP 220K 5% 1/10W
R533 1-216-793-11 METAL CHIP 4.7 5% 1/10W
R534 1-216-835-11 METAL CHIP 15K 5% 1/10W
R535 1-216-833-11 METAL CHIP 10K 5% 1/10W
R602 1-216-841-11 METAL CHIP 47K 5% 1/10W
R603 1-216-841-11 METAL CHIP 47K 5% 1/10W
R605 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R606 1-216-845-11 METAL CHIP 100K 5% 1/10W
R607 1-216-821-11 METAL CHIP 1K 5% 1/10W
< RELAY >
RY500 1-515-920-11 RELAY (24V)
*************************************************************
POWER BOARD
*************
1-533-233-31 FUSE HOLDER
< CONNECTOR >
*CN700 1-580-230-11 PIN, CONNECTOR (PC BOARD) 2P
CN702 1-819-972-11 HOLDER, CABLE 8P
*CN703 1-793-660-11 PIN, CONNECTOR (PC BOARD) 3P
< RESISTOR >
0R700 1-202-972-91 FUSIBLE 1 5% 1/4W
*************************************************************
POWER SWITCH BOARD
********************
< CAPACITOR >
0C700 1-113-925-11 CERAMIC 0.01uF 20% 250V
< CONNECTOR >
*CN701 1-568-226-11 PIN, CONNECTOR (3.96mm PITCH) 2P
< SWITCH >
0S700 1-572-267-51 SWITCH, PUSH (AC POWER) (1 KEY)
(SUBWOOFER ON/OFF)
*************************************************************
VOL-LED BOARD
**************
< CONNECTOR >
CN300 1-819-147-11 PIN, CONNECTOR 5P
< DIODE >
D300 8-719-060-27 DIODE SLR-325MCT31
(SUBWOOFER ON/OFF)
POWER POWER SWITCH VOL-LEDMAIN
All manuals and user guides at all-guides.com
all-guides.com

12
Ref. No. Part No. Description Remark
SA-WG99
< RESISTOR >
R300 1-216-823-11 METAL CHIP 1.5K 5% 1/10W
< VARIABLE RESISTOR >
RV300 1-225-483-21 RES, VAR, CARBON 20K
(SUBWOOFER LEVEL)
*************************************************************
MISCELLANEOUS
**************
51-787-344-11 FAN, DC
061-830-190-11 CORD, POWER
0F700 1-532-325-00 FUSE, TIME-LAG 6.3AL/250V
0F701 1-532-325-00 FUSE, TIME-LAG 6.3AL/250V
0F702 1-532-504-00 FUSE, TIME-LAG 4AL/250V
SP1 1-826-588-11 LOUDSPEAKER (20cm)
0T700 1-445-114-11 TRANSFORMER, POWER
VOL-LED
All manuals and user guides at all-guides.com

13
SA-WG99
MEMO
All manuals and user guides at all-guides.com

SA-WG99
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.
Ver. Date Description of Revision
1.0 2007.01 New
All manuals and user guides at all-guides.com