Sony KV-28WF1A User manual

— 1 —
KV-28WF1
DEST.COMMANDER CHASSIS NO. MODEL MODEL CHASSIS NO.
COMMANDER DEST.
RM-839 French SCC-K01S-A
KV-28WF1K
KV-28WF1R
KV-28WF1U
SERVICE MANUAL
KV-28WF1A
KV-28WF1B
KV-28WF1D
KV-28WF1E
RM-839 Italian SCC-K05Q-A
RM-839 AEP SCC-K07T-A
RM-839 OIRT SCC-K20H-A
RM-839
OIRT SCC-K20G-A
BE-3D
CHASSIS
MICROFILM
R
TRINITRON COLORTV
R
RM-839 Spanish SCC-K06S-A
RM-839
UK SCC-K04N-A

USEFUL INFO.
USEFUL INFO.USEFUL INFO.
USEFUL INFO.
Error reader.
The BE-3D chassis supports the use of the Error Reader. This jig, is available under part number S-188-900-10
(price code S).
The displayed code shows the actual error of the TV set. Refer to the service manual or the table below for an
explanation of those codes.
ERROR CODES
02 - Protection circuit trip <ANY TIME>
03 - IIC SCL LOW <POWER UP ONLY>
04 - IIC SDA LOW <POWER UP ONLY>
05 - IIC SDA and SCL LOW <POWER UP ONLY>
06 - Jungle/chroma controller no acknowledge <POWER UP ONLY>
07 - Video switch no acknowledge <POWER UP ONLY>
08 - Tuner no acknowledge
09 - MSP no acknowledge
10 - NVM no acknowledge
11 - M3L TXD LOW <POWER UP ONLY>
12 - M3L RXD LOW <POWER UP ONLY>
13 - M3L ENABLE LOW <POWER UP ONLY>
14 - M3L TXD AND RXD LOW <POWER UP ONLY>
15 - Compact Text test fail <POWER UP ONLY>
16 - AV switch cannot power on reset
17 - Cannot initialise jungle
18 - NVM acknowledge fail after initialisation
19 - Multiple devices with no acknowledge <POWER UP ONLY>
20 - Compact Text run-time failure
21 - AVSWITCH response failure after power up
22 - JUNGLE/CHROMA controller response failure after power up
23 - Compact Text does not respond
24 - Sound processor run time failure
25 - M3L bus clock low time-out after data sent (run time failure)
26 - M3L bus clock low time-out afetr data sent (power up)
27 - M3L bus clock low time-out afetr data sent (initialization)
28 - DSP run-time failure.
Replacement of HV transformer.
Two types of high voltage transformer are used (removable or fixed focus cable). When replacing a line
transformer, replace using the original type.
Type Focus cable Part no.
A Removable 1-453-169-12
B Fixed 1-453-220-11
DEFLECT
DEFLECTDEFLECT
DEFLECT
Lines tearing when hot.
[32in models only]. Replace line driver transformer T804.
No sync in TXT mode.
Replace IC1001.
PICTURE
PICTUREPICTURE
PICTURE


Horizontal interference in picture during first half hour.
IC606 is defective. Therefor unstable +9V (pin 3 of IC606). Replace 9V regulator IC606.
Ref. Description Location Part no.
IC606 LM2940T-90 D-board PSU 8-759-267-25
Visible arcing interference on screen when appliance does function. Intermittently switches off when switched
on.
Replace line output transformer T803.
Partially blanked horizontally.
Check zener diode D817 (RD5.6ESB2) in blanking circuit, for leaks.
Overbright, nearly negative picture.
Access service mode and enter TT07 to clear.
AUDIO
AUDIOAUDIO
AUDIO
Hum and/or buzz of the headphones and/or speaker when vol. is low.
Deflection unit generates interference. On board A, solder side, add a thick wire AWG18 200mm long between
pins 6,7 and 8 of IC203 and pins 29 and 30 of CN1. Given its critical position, the wire must be kept away from
board A.
Part no. Ref.
190090227 Wire AWG18
No sound. Headphones OK.
Fau;t 1: [PS6001 O/C]. Replace audio output chip IC1200 (TDA7264).
Distorted or loud crackling from audio.
Check audio demodulator/processor chip IC202 (MSP3410).
POW
POWPOW
POWER
ERER
ER
EHT comes up briefly then nothing. No error code.
[Excess current protection system operating]. Check line output transformer T803.
Intermittently switches off when switched on. Visible arcing interference on screen when appliance does
function.
Replace line output transformer T803.
Locks when hot.
Replace IC202 (MSP3410).
Shuts down when hot.
Replace IC202 (MSP3410).
FUNCTION
FUNCTIONFUNCTION
FUNCTION
No TXT. No OSD.
Check zener diode D817 (5.1V) on main PCB.
Comes on then switches to standby. Standby LED flashes twice.
(1) Check field output chip IC500 (STV9379).
(2) [OK if D505 disconnected]. Check zener diode D505 (MTZJT7736A) for leaks.
(3) [No change if D505 disconnected]. Replace memory chip NVM IC2.


Does not got into standby mode completely; picture disappears but line continues to run.
(1) Check Q602, Q603 and Q604 in standby switching circuit. Check reservoir capacitor C615.
(2) [Above components replaced; HT not at 135V]. Replace error detector chip IC602 (SE135N).
Pulses in and out of standby. RY600 clicks each time.
Check Q601 (2SC3852A), D603 (6.8V) zener and R634 (22R) on primary side of PSU.
Degaussing incomplete.
Replace relay RY600 with part number 1-755-018-11.
TUNING/MEMORY
TUNING/MEMORYTUNING/MEMORY
TUNING/MEMORY
Intermittently channels change.
Replace tactile switches S9001 and S9002 on D board.
GEOMETRY
GEOMETRYGEOMETRY
GEOMETRY
E-W bowing. Excessive width.
Check R870 (1R/1W).
OTHER
OTHEROTHER
OTHER
No OSD. No TXT.
Check zener diode D817 (5.1V) on main PCB.
Intermittently volume bar appears.
Replace tactile switches S9001 and S9002 on D board.
Incomplete or messy OSD and menus. TXT OK.
Replace IC1001.
