
KE-P37M1/P42M1 (AEP) 2-2
2-2-5. Y signal AD calibration of CCP2 decode
1. Check “MON_CON_REG_1” = 3.
(TIMING_AUTO_DETECT is Enable)
2. Input 0 IRE black full field with burst.
3. Send “READ_PW_INPUT_Y” command from ECS.
4. Check that the detection value of “PW_INPUT_Y” is
within the standard of following column.
5. Input 100 IRE white full field with burst.
6. Send “ADJUST_Y_LEVEL_VIDEO” command from ECS.
The Y_LEVEL_CCP2_04 registration of the video range is
adjusted automatic by this command.
Adjustment value also is copied in the proper NVM area.
7. Check that the detection value of “PW_INPUT_Y” is within
the standard of following column.
2-2-6. C signal AD calibration of CCP2 decode
1. Check “MON_CON_REG_1” = 3.
(TIMING_AUTO_DETECT is Enable)
2. Input 0 IRE black full field with burst.
3. Send “READ_PW_INPUT_CB” command from ECS.
4. Check that the detection value of “PW_INPUT_CB” is
within the standard of following column.
5. Input blue full field with burst.
6. Send “ADJUST_C_LEVEL_VIDEO” command from ECS.
The C_LEVEL_CCP2_05 registration of the video range is
adjusted automatic by this command.
Adjustment value also is copied in the proper NVM area.
7. Check that the detection value of “PW_INPUT_CB” is
within standard of following column.
8. Input red full field with burst.
9. Send “READ_PW_INPUT_CR” command from ECS.
10. Check that the detection value of “PW_INPUT_CR” is
within standard ofi following column.
2-2-7. Check AD (Component case) calibration
registration items
1. Select AV4 and input 575i signal.
2. Set following items.
Item Standard
PW_INPUT_Y Less than 304
Item Standard
PW_INPUT_CB Less than 304
Item Standard
PW_INPUT_Y 3888
±
16
Item Standard
PW_INPUT_CB 3184 ±16
Item data
PICTURE_MODE 0 (Live)
COLOR 25
DYNA_PICT 0 (Off)
DC_TRAN 0 (Off)
3. Check that following items is defalt.
2-2-8.Ysignal AD calibration of component input
1. Check “MON_CON_REG_1” = 3.
(TIMING_AUTO_DETECT is Enable)
2. Input 0 IRE black full field with burst in AV3.
3. Send “READ_PW_INPUT_Y” command from ECS.
4. Check that the detection value of “PW_INPUT_Y” is within
the standard of following column.
5. Input 100 IRE white full field with burst.
6. Send “ADJUST_Y_LEVEL_VIDEO” command from ECS.
The Y_LEVEL_CCP2_04 registration of the video range is
adjusted automatic by this command.
Adjustment value also is copied in the proper NVM area.
7. Check that the detection value of “PW_INPUT_Y” is within
the standard of following column.
2-2-9. C signal AD calibration of componet input
1. Check “MON_CON_REG_1” = 3.
(TIMING_AUTO_DETECT is Enable)
2. Input 0 IRE black full field with burst.
3. Send “READ_PW_INPUT_CB” command from ECS.
4. Check that the detection value of “PW_INPUT_CB” is
within the standard of following column.
5. Input blue full field with burst.
6. Send “ADJUST_C_LEVEL_VIDEO” command from ECS.
The C_LEVEL_CCP2_05 registration of the video range is
adjusted automatic by this command.
Adjustment value also is copied in the proper NVM area.
7. Check that the detection value of “PW_INPUT_CB” is
within standard of following column.
8. Input red full field with burst.
9. Send “READ_PW_INPUT_CR” command from ECS.
10. Check that the detection value of “PW_INPUT_CR” is
within standard ofi following column.
Item Standard
PW_INPUT_Y Less than 304
Item Standard
PW_INPUT_Y 3888
±
16
Item Standard
PW_INPUT_CB Less than 304
Item Standard
PW_INPUT_CB 3760 ±16
TARGET_PW_IN_Y
ADJ_Y_DEADBAND
ADJ_Y_LOOPATTEN
TARGET_PW_IN_C
ADJ_C_ DEADBAND
ADJ_C_ LOOPATTEN
AD_ADJ_TIME_OUT
Item Standard
PW_INPUT_CR 2832 ±320
Item Standard
PW_INPUT_CR 3200 ±320