Sony WEGA KV-27FA210 User manual

SONY 4-100-520-21
F# Trinitren ®
Operating Instructions
KV-2 7FA210
© 2003 by Sony Corporation

WARNING
To reduce the risk of fire or electric shock, do not expose the
TV to rain or moisture.
ATTENTION
RtSQUE DE CHOC ELECTRIQUE,
NE PAS OUVRIR
PRECAUCION
RtESGO DE CHEQUE ELECTRODe
NO ABRIR
CAUTION: TO SEDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVES (OR RACK).
NO USER-SERVICEABLE PARTS iNSiDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the user to tile
presence of uninsulated "dangerous voltage"
within tile product's enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
This symbol is intended to alert the user to tile
presence of important operating and maintenance
(servicing) instructions in tile literature
accompanying tile appliance.
Note to the CATV Installer
This reminder is provided to call the CATV system
installer's attention to Article 820-40 of the NED: that
provides guidelines for proper grounding and, in particular,
specifies that the cable ground shall be connected to the
grounding system of the building as close to the point of
cable entry as practical.
SAFETYPRECAUTIONS
[_ Operate the TV only on 120 V AC.
[_ One blade of the power plug is wider than the other for
safety purposes and will fit into the power outlet only one
way. If you are unable to insert the plug fully into the
outlet, contact your dealen
[_ [f any liquid ol; solid object falls into the TV, unpl ug it and
have it checked by qualified personnel before operating it
further.
CAUTION
When using TV games, computers, and similar products
with your TV, keep the brighh/ess and contrast functions at
low settings. If a fixed (non-moving) pattern is left oil the
screen for long periods of time at a high brightness or
contrast setting, the image can be permanently imprinted
onto the screen. Continuously watching the same channel
can cause the imprint of station loges onto the TV screen.
These types of imprints are not covered by your warranty
because they are tile results of misuse.
/_ To reduce the risk of electric shock, do not use
this polarized plug with an extension cord,
receptacle, or other outlet unlessthe blades can
be fulty inserted to prevent blade exposure.
7"J rou are cautlonea mat any cnanges or modifications
not expresslyapprovea In IRIS manual COLa veto
four aumorlty to operate IRIS eaUl[ q/enL
NOTIFICATION
This equipment has been tested and found to comply with
tile limits for a Class B digital device pursuant to Part 15 of
tile F(C Rules. These limits are designed to provide
reasonable protection a_,ainst harmful interference in a
residential installation. _his equipment generates, uses, and
can radiate radio h:equencv energy and, it not installed and
used in accordance with tt:_e instructions, may cause
harmful interference with radio communications. However,
there is no guarantee that interference will not occur ill a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
[_ Reorient or relocate the receix ing antennas.
[_ [ncrease the separation between the equipment and
i:eceiver.
[_ Connect the equipment into an outlet on a circuit different
h:om that to which the receiver is connected.
[_ Consult the dealer or an experienced radio/TV technician
for help.
Protecting the TV
[_ To prevent internal heat build-up, do not block the
_ entilation openings.
[_ Do not install the TV in a hot or humid place, or in a place
subject to excessi_ e dust el mechanical vibration.
Note on Caption Vision
This television receiver provides display of televiskm closed
captioning in accordance with § 15.119 of the FCC rules.
Use of this television for other than private viewing of
programs broadcast on UHF or VHF or transmitted by cable
companies for the use of the general public may t:equire
authorization from the broadcaster-cable company and/or
program o%r['ler.
Owner's Record
The model and serial numbers are located on the front cover
of this manual and at the rear of your: TV.
Trademarks and Copyrights
• 0- •-
ENERGY STAR Is a registered mark.
As an ENERGYSTAR Partner,Sonyhas
determined that this product e_product
model meets the ENERGYSTAR guidelines
for energy efficiency.
WEGA_0, FD Trinitron, Caption Vision, D} namic Bass l;:esponse
S}stem md Stead} Sound are registered trademarks of Son}
CorporaH on.
Licensed b_ BBE Sound, Inc. tinder USP 4638258.4482866. BBE and
BBE symb(d are trademarks of BBE Sound, Inc.
®
"WOW, TruSurround, and the (@) symbol are
trademarks of SRS Labs, Inc. WOW technology is
incorporated under license from SRS Labs, Inc."

IMPORTANT SAFEGUARDS
For your protection, please read these instructk)ns
con_pleteb.', and keel:) this manual for future reference.
(arefullv observe and comply with all warnings, cautions
and insti_uctions placed on the, set, or described in the
operating instructions or service manual.
WARNING
To guard against injury, the following basic safety
precautions should be_observed in the installation, use, and
servicing of the set.
Use
Power Sources
This set should be operated only from i
the type of power source indicated on F.
the serial/model plate. If you are not _ ('q _,_J'--
st "_ of th • type of • ect" ca pew _r ff _<;_@9_-- _
supohedtow,urhom_,,consultyour i _;_ _!1,_
deaJer or hx:al power company. For _ "_'_"'_'_
those sets designed to operate'from
battery power, refer to the operating instructions.
Grounding or Polarization
This set ]nay" be equipped with apolarized alternating current
line plug (a plug having one blade wider than other). This
plug _;ill fit into the po_; er outlet onl} one _;ay. This is a safety
feature. If you are unable to insert the plug fully into the
outlet, try reversing the plug. If the plug still fails to fit, contact
your electrician to replace }our obsolete outlet. Do not defeat
the safety purpose oithe polarized plug.
For the set with a polarized AC power cord plug
This plug will fit into the power outlet
only one waD This is a safer? feature. _.._-/-_r _
If _ou are unable to insert the plug _/
fully into the outlet, try reversing the _--_
plug. If the plug still fails to fit, contact
your electrician to have a suitable outlet installed. Do not
defeat the safety purpose of the polarized plug by forcing it in.
Alternate Warning
Forthe set with a three-wire groundingtype ACplug
This plug will only fit into a
grounding-type power outlet. This is
a safety feat{n:e. If you are unable to
insert the plug into the outlet, contact
your electrician to have a suitable
outlet installed. Do not defeat the
safety purpose of the grounding plug.
Overloading
Do not overk_ad wall
outlets, extension (_}_'_("
cords or convenience _1 _]/_-.
receptacles beyond
their capacity, since
this can result in fire
or electric shock.
Ahvavs turn the set off when it is not to be used. When the
set is left unattended and unused for long periods of time,
unplug it from the wall outlet as a precaution against the
possibility of an internal malfunction that could create a fire
hazard.
Do not disconnect the antenna or the power cord during a
heavv storm. Lighlning may strike while you are holding
the c_lble or cord, causing serious injur}_ Turn off your TV
and wait for the weather to improve.
Object and Liquid Entry
Never push o_cts of any kind into the set
through the cabinet slots as they may touch
dangerous voltage points or short out parts
that could result in a fire or electric shock.
Never spill liquid of any kind on the set.
Attachments
Do not use attachinents not recoin]Tlended
by the manufacturer, as they may cause
hazards.
Do not place an)' objects especially heavv
objects, on top of the set. The object may
fall from the set, causing injury.
Cleaning
Unplug the set from the wall outlet before
cleaning or polishin_ it. Do not use liquid
cleaners or aerosol cleaners. Use a cloth
lightly dampened with water for cleaning
the exterk)r of the set.
If a snapping or popping sound from a TV set
is contimlous or frequent while the TV is
operating, unplug the TV and consult your
dealer or service technician. It is normal for
some TV sets to make occasional snapping or
popping sounds, particularly when being
turned on or off.
Installation
Ahvavs use two or more people to lift or move the set. The
set is heavy and the bottom sin:face is flat. Serious injury can
result from trying to move the set by yourself alone, or from
unsteady handling.
Install tl_e set on a stable, lew_l surface.
Water and Moisture
Do not use power-line
operated sets near _; ater --
for example, near a bathtub,
_t*_ashbo_;1, kitchen sink, or
laundry tub, in a wet
basement, or near a
swimming pool, etc.
Accessories
Do not place the set on
an unstable cart, stand,
tripod, bracket, table,
or shelf. The set may
fall, causing serious
in uryto a child or an
adu t, and serious
damage to the set. Use
only a cart or stand l_ecommended by the manufacturer for the
specific model of TV. Any mounting of theproduct should
follo*; the manufacturer's instructions, and should use a
mounting accessory recommended b_ the mamlfacturer. An
appliance and cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may cause
the appliance and cart combination to ox erturn.
Ventilation
The slots and openings in the cabinet and in the back or
bottom are provided for necessary venti alton. To ensure
reliable operation of the set, and to protect it from
overheating, these slots and openings must never be
blocked or covered.

Nevercovertheslotsand openings
with acloth or other materials.
Never block the slots and openings
by placing the set on a bed, sofa, rug
or other similar surface.
Never place the set in a confined
space, such as a bookcase or built-in
cabinet, unless proper ventilation is
provided.
• Do not place the set near or over a
radiator or heat register, or where it is
exposed to direct sunlight.
Power-Cord Protection
Do not allo_ anything to rest on or roll over the
po_; er cord, and do not place the set where the
po_; er cord is subject to _;ear or abuse.
Antennas
Outdoor Antenna Grounding
If an outdoor antenna is installed, follow the precautions
below. An outdoor antenna system should not be located in
the vicinity of ovechead powder lines or other electric light oc
powel: circuits, or where it can come in contact with such
powel: lines ol: circuits.
WHEN INSTALLING AN OUTDOOR ANTENNA
SYSTEM, EXTREME CARE SHOULD BE TAKEN TO KEEP
FROM CONTA(: TING SU(:H POWER LINES OR
(: IRQ UITS AS CONTACT WITH THEM IS ALMOST
INVARIABLY FATAL.
Be sure the antenna system is grounded so as to provide some
protection against voltage surges and built-up static charges.
Section 810 of the National Electrical Code (NEC) in USA and
Section 54 of the Canadian Electrical Code in Canada
provides information with respect to prt_per grounding of the
mast and supporting structure, grounding of the lead-in _;ire
to an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
Antenna Grounding According to the NEC
Antenna Grounding According to the National Electrical
Qode, ANSI/NFPA 70.
NA
LEAD IN
{;LAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
ERVlOE GROU[IDING
ELECTRODE SYSTEM
NEC. NATIONAL ELECTRIC CODE (NEC ARTICLE 250 PART H)
Lightning
For added protectinn for this televisinn receiver during a
lightning stoml, or when it is left unattended and unused
for long periods of time, unplug it from the wall outlet and
disconnect the antenna. This will prevent damage to the
l:eceiver due to lightning and powerqine surges.
Service
Damage Requiring Service
Unplug the set from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
• When the power cord or plug
is damaged or frayed. _ _)"--=4TL'_,_
• If liquid has been spilled
into the set or objects have
fallen into the product.
• If the set has been exposed to
rain or water.
• If the set has been subject to
excessive shock by being
dropped, or the cabinet has
been damaged.
If the set does not operate ,_z::= _
normally when following the operating _
instructions. Adjust only those controls i_
that are specified in the operating "it_i_ _ "
instructions. Improper ad]justment of [_? •
other controls may result in damage and
will often retluire extensive workby a
qualified technician to restore the set to normal operation.
• When the set exhibits a distinct change in
performance -- this indicates a need for service.
Servicing
Do not attempt to service the set yourself
since opening the cabinet may expose you
to dangerous voltage or other hazards. Refer
all servicing to qualified service personnel.
Replacement Parts
When replacement parts are required, be
sure the service technician certifies in
writing that he has used replacement
i_arts specified by the manufacturer that
ave the same characteristics as the
original parts. Unauthorized
substitutions may result in fire, electdc
shock, or other hazards.
Safety Check
Upon completinn of any service or repairs to
the set, ask the service technician to perform
l:outine safety checks (as specified by the
manufacturer) to determine that the set is in
safe operating condition, and to so certify.
When the set reaches the end of its useful" life,
improper disposal could result in a pictul:e
tube implosion. Ask a qualified service
technician to dispose ot the set.

Contents
Introduction ®
Introducing the FD Trinitron WEGA Features ........................................................................ 1
About this Manual .......................................................................................................................... 2
Batteries for the Remote Control .................................................................................................. 2
Front Panel Menu Controls ........................................................................................................... 2
Using the Remote Control
Remote Control Description .......................................................................................................... 3
Programming the Remote Control ............................................................................................... 5
Manufacturer's Codes .................................................................................................................... 6
Using your TV Remote Control with Other Equipment ........................................................... 7
Connecting Your TV
TV Rear Panel ..................................................................................................................................9
Basic Connections ......................................................................................................................... 11
Dynamic Bass Response System Connection (Subwoofer) .................................................... 12
Connecting Additional Equipment ............................................................................................ 13
Using Basic Functions
Setting Up the TV.......................................................................................................................... 21
Quick Start to the Menus ............................................................................................................. 22
Using the Menus
How to Access Menus .................................................................................................................. 25
Using the Video Menu ................................................................................................................. 26
Using the Audio Menu ................................................................................................................ 27
Using the Channel Menu ............................................................................................................. 29
Using the Parent Menu ................................................................................................................ 31
Parental Control ..................................................................................................................... 32
United States: Selecting Custom Rating Options .............................................................. 34
Canada: Selecting Custom Rating Options ........................................................................ 36
Using the Timer Menu ................................................................................................................. 37
Using the Setup Menu .................................................................................................................. 38
Using the Basic Menu ................................................................................................................... 39
Other Information
Troubleshooting ............................................................................................................................ 41
Specifications ................................................................................................................................. 45
Index ...................................................................................................................................................... 47

Introduction
Congratulations on your purchase of the Sony FD Trinitron WEGA ®.
Introducing the FD Trinitron WEGA®Features
Some of the features you will enjoy include:
FD Trinitron Flat CRT-- Delivers a picture with uncompromising accuracy and
outstanding image detail via a technologically advanced tube.
_1 Dynamic Bass Response System -- Enhances low-frequency sounds with a powerful
subwoofer. New and exclusive from Sony.
_1 Y, PB,PRInputs -- Provides component video inputs for superior picture quality
(480i only).
WOW -- Provides a dramatic presence with a full, deep bass sound. When WOW is
enabled, BBE is directly activated to further enhance the audio performance.
TruSurround -- Produces a dynamic three-dimensional sound for stereo audio signals.
BBE-- Gives sound more impact by using audio technology to compensate for phase
effects in speakers.
Parental Control (V-Chip) -- Helps parents monitor what their children watch on TV by
establishing rating limits.
_1 Favorite Channels -- Provides instant access to your favorite channels with the touch of a
button.
Info Banner -- Displays the name and the remaining time of the current program, if
available.
Universal Remote Control -- Operates your connected cable box, VCR, digital satellite
receiver, or DVD player.
Energy Star ®-- Meets the Energy Star guidelines for energy efficiency.
Front Panel Controls -- Allows access to the on-screen menus without the use of a remote
control.
_1 Front A/V Inputs -- Lets you quickly connect video games, camcorders, or stereo/mono
equipment.

Operating Instructions
About this Manual
This manual provides instructions to help you enjoy your new TV. It shows you how to
connect to an antenna or cable, cable box, VCR, DVD, satellite receiver, stereo system, or
camcorder. Once your TV is connected, follow the instructions and use the remote control to
access the on-screen menus.
Batteries for the Remote Control
hrsert two AA (R6) batteries (supplied) into the remote control using the following illustration
as a guide.
/iY_-_ Under normal conditions batteries will last up to six months. If the remote control does not operate
pr0Per!y,the batteriesmight beWoin Out
If you Willnot be usingthe remotecontrol foran extendedperiod Oftime, removethe batteriesto
avoid possibledamagefrom battery leakage.
Front Panel Menu Controls
[ "
WSVIDEO --VOLU[ae_
The front Audio/Video panel controls allow you to access the menu without the remote
control.
Press ME.UOto display' the on-screen menu.
13 Use the (_) and (_) buttons on the front Audio/Video panel instead of your remote
control.
Use the @ button on the front Audio/Video panel to navigate through the menus, then
select an item. The front panel controls also allow you to change your channels (CH+/-),
adjust the volume (VOL +/-), and change video hrputs.
_ Tonavigatethe menusWith your remotecontrol see"using the MenUs:'Onpage 25

Using the Remote Control
Remote Control Description
.....................................6_J#I
_M TNG A " "
"v'__ [.........................................';:m.
OF _C_II_ SA'CA_LE W
i® ® ®LL
VOL OH
,-4_? RM=Y18#
Button Description
[] MUTING Instantly turns off the sound. Press again or press
voL to restore the sound.
[] SYSTEM OFF Powers off all Sony equipment at once (may not
.......[] work with older equipment).
,.,..,,,,,[_[_ TV/VCR Press when you are finished using a VCR and you
want to switch to the TV Antenna input. Your VCR
power will remain on.
.........[]_ 6iSf6hEa66E .................Cyc>sth_o[;_hth,,a_:_;i_BieV;_o Mode,;_,ii;ng_i......
r_q[_ SLEEP Turns the TV off automatically in approximately 15,
ULTJ 30, 45, 60 or 90 minutes. Cancel by pressing until
..........[] Sleep Off appears.
i :
r_ [] JUMP Press to lump back and forth between two channels.
_""111_j The TV alternates between current channel and the
.........[] last channel that was selected.
[] @ Press for a direct selection of Effect settings
CD (Simulated, WOW, TruSurround, Off) (see page 27).
W!SA_
[] [] RESET Press to return to factory settings while in an on-
.......... screen menu.
1_[] CODE SET Use to program your remote control to operate
connected video equipment (see page 5).
[] POWER Press when you want to turn connected equipment
on or off.
....... ] .........
[] FUNCTION Press when you want to control connected
equipment with your remote control.
[] VCR/DVD Operates VCR or DVD. Use when you want to
(operating) operate connected VCR or DVD with your remote
control.
[] TV/VIDEO Cycles through available video inputs.
[] DISPLAY Press once to show current time (if set) and channel
number. Press again to turn DISPLAY off.
[] MTS/SAP Cycles through the Multi-Channel TV Sound (MTS)
options: Stereo, Mono, and Auto SAP (Second
Audio Progranr).
ENTER buttons to select a channel, then press ENTER.
[] GUIDE Brings up the custom guide of your satellite
receiver.

Operating Instructions
Button Description
[] _ Moves the cursor in the on-screen menus. Press the
i arrow buttons to move the cursor. Press the center
button to select or access an option.
[] MENU Displays the on-screen menu. Press again to exit the
menu at any time.
[] CH (channel) Press when you want to change channels.
#_nl# you loseyour remote ContioI, See page 52.

Using the Remote Control
Programming the Remote Control
In order to use your remote control with other equipment, you need to program your remote
control. Use the following procedure to program the remote control.
1Check the list of "Manufacturer's Codes" on page 6 and find the three-digit code number
for the manufacturer of your component. If more than one code number is listed, use the
number listed first.
CODESET
2Press CED.
VCRYDVD SAT/CABLE l COOESET
/d_ The _and CZD button wdlflash whenyou press CZD:
3Press _ or s_E button to indicate the type of component you want to program with
the remote control.
/_ YoumustdOste 4 Within 10 SecondsOfste 3 Or oUmustiedo ste s2 and3
p p ,y p .
4Use the (_-(_ buttons to enter the three-digit manufacturer's code number.
ENTER
5Press O"
6To check if the code number works, aim the TV's remote control at the component and
press on the green POWER button (VCR/DVD, SAT/CABLE, TV) that corresponds with
that component. If it responds, you are done. If not try using another code listed for that
manufacturer.
#_,_ If you have pioblemS programming youi remote c0ntrol;see "Troubleshooting'! on page 4i: